Question about Cars & Trucks

Open Question

Manuel for 2011 Hyundai-elantra-touring-headlight assembly

Need to find the description of how to change the headlight assembly

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 840 Answers

SOURCE: Adjusting the low beam headlight

its all the same the headlight is a complete unit you adjust both/ look for screws behind the headlight one each side one is for horizontal annd the other is for vertical Please rate my response thank you very much

Posted on Jan 31, 2009

Ad
USfalcon
  • 175 Answers

SOURCE: How to replace headlight bulb hyundai elantra 2004

yes , you need to remove the headlight cover from the back after u move the bulb conector then there is a holder for the bulb u need to push down then move.
i hope it help ,,,, thanx

Posted on Mar 16, 2009

  • 1986 Answers

SOURCE: Can't find headlight adjustment screws

They nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.


Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 17, 2009

Testimonial: "The adjustment screw (for passenger side) is located between the battery & frame's second hole. Turning counter-clockwise, it adjusts downwards,Thanks"

ghost45
  • 1280 Answers

SOURCE: How do I change the headlight angle on a 2004 Elantra

Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Posted on Oct 04, 2009

  • 1986 Answers

SOURCE: Adjustment headlights '02 Hyundai Elantra

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Oct 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 hyundai elantra headlights electrical problem


by slamming down the bonnet makes the light work indicates a loose bulb or a bad/loose earth in the system. Check that the bulb is tight under the fitment springs that hold it in the reflector and that the earth wires are making good contact on the bulb and where it earths out

Apr 09, 2014 | 2010 Hyundai Elantra Touring

1 Answer

2011 Hyundai Elantra - dead battery, jumped ok,,, autozone said it was is a bad voltage regulator


could be its part off the altenator usely ??could be bad battery cells ?? sounds right too me >>>>

Sep 07, 2011 | 2011 Hyundai Elantra Touring

1 Answer

Automatic gearshift is sticking...very hard to get it from park to drive


Your facing a failing safety release mechanism. when you put the key in the ingition and step on the brake pedal a safety release should be heard in the gear selector, when this device retracts now you can select a gear position , here the thing it say 2011 Hyundai Elantra? this is too new to be doing this This can be done irregardless of warranty,

Apr 28, 2011 | 2011 Hyundai Elantra Touring

1 Answer

I need to change the low beam headlight bulb


  1. Remove headlight mounting bolts and nut
  2. Remove assembly
  3. Install headlight assembly (with new bulb)
  4. Replace/tighten headlight mounting bolts and nut
e2ac826.gif


Oct 30, 2009 | Hyundai Motor 2003 Elantra

2 Answers

How do I replace 2000 Hyundai Elantra Low Beam Headlight


part # 9003ST...back of headlamp bucket..undo connector then twist out bulb assembly...do not touch glass on replacement bulb as your hands oils will cook the new bulb

Dec 08, 2008 | 2000 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...