Question about 2005 Chevrolet Aveo

1 Answer

If one cv joint goes how likely is it for the other to go

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Depending on the condeition of the other one

Posted on Oct 28, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

If cv joint is bad car has a lot of vibration, boots arent torn or leaking, but makes a humming noise. is this cv joint or something else?


cv joints should not click as that is the first indication of a failed unit
( going slow and changing direction produces a click,click is a cv joint)
wheel bearings should not be tight as that will produce a humming noise and will result in early failure
because the axle turns with the change of direction ,the distance from the pivot point to the transmission changes and so the shaft will move in and out of the transmission to compensate
take it to an accredited drive line specialist for a diagnosis

Jun 07, 2015 | 2000 Ford Taurus

1 Answer

Where is toyota constant velocity u-joint located


Like all front-drive cars using CV joints, there are 4 CV joints on the car near the engine. The vehicle has 2 axles (left and right, driving the corresponding front wheel). Each axle has 2 joints, one on each end. Typically the outer CV joints fail first, as their range of movement is greater due to steering the vehicle.

In modern practice the entire left or right axle is replaced when a CV joint goes bad.

Constant Velocity joints and U-joints perform a similar function, but are not really the same thing. U-joints are more typically used on rear-drive or truck-based 4WD vehicles.

Apr 27, 2014 | 2002 Toyota ECHO

1 Answer

How to remove the cv joint boot on hyundai accent


If you clean away the grease inside the boot and look where the axle goes into the joint there is a snap ring there. Spread the snap ring and pull the joint off the axle.

Oct 02, 2012 | Cars & Trucks

2 Answers

Cv joint is going out car is being driven but will not go fast. what happens when the cv joint goes out does the car stop driving


If it goes out completely that can cause some damage. Yes It will stop, depending on which side (pass/drivers) goes.

Nov 21, 2010 | Chevrolet Cavalier Cars & Trucks

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

Just installed new rotors,brake pads, bearings and tie rods to front of 2000 montana. have a whopping sound when driving , this goes away when wheels turned slightly right. when turning right corner hear a...


One of your CV joints are bad, inspect which CV joint needs to be replaced. Roll your windows down and make tight right and left corners in an empty parking lot slowly and listen for the clicking noise. If it's coming from the passenger side window or the drivers side window, which ever side the noise is coming from is the side that the CV joint has failed and will need to be replaced.
Thank you for using FIxya and replacing the front wheel bearing improperly buy hammering the CV joint out instead of using a wheel bearing puller will cause damage to the CV joint as to what you have described. Good luck and keep us posted.

Jul 20, 2010 | 2000 Pontiac Montana

2 Answers

Inner cv joints


inner cv joints are the joints on the inner half of the axle shaftswhere they go into the transmission. sometimes the easiest thing to do is replace the axle shafts

Jan 05, 2009 | 1996 Chrysler LHS

1 Answer

Any guides on how to check a cv joint?


Usually when a CV joint goes bad, it's because the rubber boot has become torn or otherwise open to the elements, and dirt/grit/etc has gotten in there and ruined the joint. If the boots are intact, chances are that the CV joint is OK.

It may be a wheel bearing too - this could be an early sign of it. Audi is known for wheel bearing failures.

Jul 25, 2008 | 2000 Audi A6

Not finding what you are looking for?
2005 Chevrolet Aveo Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...