Question about 1994 Nissan Pickup

1 Answer

1994 nissan pickup 4x4 2400 where should the rotary point when at top dead center

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 293 Answers

Do you mean the distributor pick-up rotor? If it is and you are referring to the number 1 piston, the tip of the pick-up rotor should be a little bit pass the #1 contact terminal of the distributor cap. The tip should be exactly at the terminal when the piston is at the specified position before the top dead center (BTDC).

Posted on Oct 28, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 26 Answers

SOURCE: timing belt

try removing spark plug No1 and insert a rod or fine screw driver and detect the top dead point of the piston.

Posted on Jul 06, 2008

  • 2 Answers

SOURCE: 1995 NISSAN PICKUP WHEN STOPPING GOES DEAD. IDLE

Have you tried cleaning the throttle body?

Posted on Apr 28, 2009

  • 1129 Answers

SOURCE: My 1994 Nissan pickup brakes shudder at low speed

Inspect the brake rotors for grooving and score marks and also look to see if there are any heat cracks, if there is grooving or very little brake pad material remaining replace the brake pads and also two new rotors, it is also possible that it is just a frozen or stuck brake caliper, this would be indicated by an uneven rotor one that has more metal or meat on one side that the other also uneven brake pads indicates an uneven brake caliper application

Posted on Aug 02, 2009

roniecon
  • 6826 Answers

SOURCE: My 1994 Nissan Pickup was showing the battery light

The alternator is not charging,need to replace it,and charge the battery up with a slow charge,,,2 amp,over night a then some,slow charging gets the charge all the way up,and creates a deep charge that will stay,and prolong the battery life.

Posted on Apr 23, 2010

  • 2 Answers

SOURCE: I'm looking to buy a 1994 Nissan pickup but it's

I had the same problem on my 1997 Nissan Pickup XE. I got my mechanic to adjust the idle speed. It's a pretty simple and easy thing to do if you know what you are doing.

Posted on Aug 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you set the timing on a 1991 Nissan pickup truck 2.4 L 4cyclinder D 21


Autozone lists that engine timing at 10 degrees before top dead center with the engine warm and idling at 800 RPM. That is with the transmission in neutral (parking brake on) and all accessories off. It also states timing and idle speed are electronically controlled and non-adjustable.

Aug 17, 2015 | 1991 Nissan Pickup

1 Answer

What is the ignition timing for 2002 nissan hardbody 2000i 16v


Here are the 3 engines listed for this year. IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 2.4L SFI 4cyl

The Ignition Timing

18-22 DegreesBefore top dead center - When throttle positionsensor disconnected and using suitably programmedscan tool.When adjusting idle speed, set parking brake & chock drive wheels, curb idle speed (750-850 RPM)transmission in neutral.

IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 3.3L SFI 6cyl

The Ignition Timing

8-12 DegreesBefore top dead center - throttle position sensorharness disconnected.When adjusting idle speed, set parking brake & chock drive wheels, curb idle speed (700-800 RPM)transmission in neutral.

IGNITION TIMING

2002 Nissan/Datsun Truck Frontier Pickup 2WD 3.3L SFI SC 6cyl

The Ignition Timing

8-12 DegreesBefore top dead center - throttle position sensorharness disconnected.When adjusting idle speed, set parking brake & chockdrive wheels, curb idle speed (700-800 RPM)transmission in neutral.

Jun 05, 2015 | Nissan Hardbody Cars & Trucks

2 Answers

I have a 1994 nissan 2.4L pickup.I am currently in the process of changing the timing chain,cam gear and crank gear. In this process I noticed that the keyway on the crank gear is not in the up posit


Same happened to me. Economic way to ensure its at tdc is to remove #1 plug, using a thin dowel rod mark the distance it travels inside spark plug hole. Turn crankshaft slightly until you can measure the #1 piston is at its highest position. You'll be at tdc.

Jan 29, 2015 | 1994 Nissan Pickup

1 Answer

Ignition timing



1991 Nissan/Datsun Truck D21 Truck 2WD 3.0L FI 6cyl

The Ignition Timing
15 Degrees Before top dead center*Warm idle speed 750 RPM*Transmission in neutral (Parking brake engaged)*All accessories off.

1991 Nissan/Datsun Truck D21 Truck 2WD 2.4L FI 4cyl

The Ignition Timing
10 Degrees Before top dead center*Warm idle speed 800 RPM*Transmission in neutral (Parking brake engaged)*All accessories off.

Mar 24, 2014 | 1991 Nissan Pickup

1 Answer

I have a 1994 nissan pickup that has trouble getting up mto speed and trembles when it is doing so


Sounds like a dead missfire. Wire lead arcing out. I would put spark plugs and a wire set on it. should be easy. May want to do the distributor cap and rotor as well.

Feb 24, 2012 | 1994 Nissan Pickup

1 Answer

94 yota pickup V6. Timing belt failed, replaced it, now it's running rough and lacks power. Ideas?


The engine is a free running type so bent valves should not be the problem. Recheck the timing marks on the camshafts and crankshaft. If you are one timing belt tooth off, the engine could run but run rough. With the number 1 cylinder piston at top dead center, the camshaft marks should be lined up with their "TDC" marks and the crankshaft mark should be at 0 deg.

If the distributor was removed during the belt replacement, make sure it is in time with the crankshaft timing mark. When the No. 1 cylinder piston is at top dead center, the crankshaft timing mark should be on 0 deg. and the distributor rotor should be pointing to the number 1 terminal on the distributor cap at the same time.

Mar 10, 2011 | 1994 Toyota Pickup

1 Answer

Top dead center-how can you tell where the rotor is pointing since it's round to see if it's pointingto #1 spark plug


The rotor may be round but it has a metal contact point on it. When that is pointing to the #1 spark plug wire position on the distributor cap and the TDC timing marks on the crankshaft pulley are lined up, it is at #1 TDC.

Feb 18, 2011 | 1985 Nissan Pickup

2 Answers

IS SETTING THE TIMING AS SIMPLE AS GETTING THE TIMING MARKS LINED UP? IF SO I HAVE DONE SOMETHING WRONG ANY SUGGESTIONS WOULD BE APPRECIATED


You have to make sure the engine is at top dead center on number one cylinder (all valves closed on number one cylinder) - if distributor installed check that #1 is on firing position so is not on exhaust stroke and or remove spark plug and put plastic straw in hole to see if piston is at TDC (top dead center) ready to fire on compression stroke.
After setting timing always rotate engine 4 times to bring back to same location and that nothing like pistons bump into valves etc. and make sure that timing marks are at the location. If you install backwards on some engines the oil pump will not be in line to accept oil and will not get oil pressure - I believe this true of 3.1 chev or was it 3.8 I messed up on, lol

Jun 09, 2010 | 1994 Nissan Pickup

1 Answer

Timing mark 1994 sentra 1.6l out of 5 marks what


The timing marks indicate degrees of advance. Thus, the first mark would be top dead center and in increments of two it increases to 10 degrees before top dead center.

Nov 03, 2009 | Nissan Sentra Cars & Trucks

2 Answers

How to set the Timing on a 1994 b2300 mazda pickup


the timing is 10 degrees before top dead center but its non- adjustable........ clearpixel.gif Non-adjustable.

Dec 10, 2008 | 1994 Mazda 2WD B Series Pickup

Not finding what you are looking for?
1994 Nissan Pickup Logo

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...