Question about 2002 Dodge Caravan

1 Answer

If ALL the door locks are not working with the key remote or the switches, what can cause theis problem?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 444 Answers

Fuse blowin or a defective relay.

Posted on Oct 27, 2012

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2002 Dodge Grand Caravan Driver Door Lock/Unlock Switch

sorry not sure the 12v prob will help this swtich works on 5v off 3v unlock 1v lock single wire lock/unlock logic signals
I found wiring diagrams at
http://www.dodge.com/bodybuilder/2004/docs/wd/rswd/tc.pdf
it is 2004 but use the wiring diagrams to test the wires
(most likely to fail where they flex)
because it is using logic gates disconnect the plug at each end of the wire you are testing or the damn thing will find a few diffrent ways to trick you.

Posted on Apr 21, 2009

  • 1 Answer

SOURCE: key/door power lock does not work

A short term fix is to pull the IOD fuse, wait about 10 seconds then replace it again. You'll have to reset your clock, which is annoying but the locks will work again. In the past 3 days, I've had to pull this twice because my locks quit--Hoping to find a more permanent solution.

Posted on Sep 08, 2009

  • 412 Answers

SOURCE: power door locks do not work

2004-2005 CARAVANS HAD A SOFTWARE ISSUE IN THE BODY CONTROLLER..REMOVING AND REINSTALLING IOD FUSE IN UNDERHOOD FUSEBLOCK..THERE IS A SOFTWARE UPDATE FOR THE BODY CONTROLLER FROM CHRYSLER..TAKES ABOUT AN HOUR TO COMPLETE..AS FAR AS I KNOW,THEY ARE ONLY ONES WHO CAN DO THIS

Posted on Sep 24, 2009

janlinekbmw
  • 146 Answers

SOURCE: My door locks won't work. They aren't working with

In drivers side is damaged the driving motor for central doors locking. When is not works other doors also do not work! Try to unlock the car from the passenger side and you will see that the door is open all outside the driver's door! So you know that there is a problem!

Posted on Jun 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The drivers side cook lock does not lock or unlock using the remote. The other door do respond to the remote. What is the cause and solution?


Hi Charles

The drivers side door gets the most use
Check the actuator wiring coming through the door hinge
If it works from the key then the Power to the door is OK & the key switch is ok. Must be trigger wire from wireless device receiver!

Good Luck

Hyundai Door Lock Actuator eBay

Hyundai Entourage Alarms Remote Car Starters Keyless Entry Locks

Jul 08, 2015 | 2008 Hyundai Entourage

1 Answer

So far, what I have tried hasn't worked. Guess I will have to take off door panel. But which door? Driver side door locks and unlocks with remote, with key and with inside door switch. Passenger door...


Since the driver's door gets the most use, and all circuits run through the master switch, check driver's door first and check the wiring at the hinge area for breaks.

Jan 29, 2015 | Cars & Trucks

1 Answer

Xj8 door lock


You need to replace the lock actuator in the doors that are not locking/unlocking with the door switch/remote. If the remote works for most of the doors then it is fine. The actuator is what moves the lock when it gets the signal from the remote or door switch to move it.
Good luck

Jul 11, 2013 | Cars & Trucks

1 Answer

Replaced batery in key fob and now there is no connection between fob and security system...I can lock and unlock doors with the key and I can start car ...fob doesn't work; does not lock or unlock...


reprogram the remote transmitter. first leave driver door open all other doors closed,key removed from the ignition switch. insert key into the ignition switch,then remove it.press lock and unlock on the vechicle door lock control switch at 1 second intervals 5 times. close and repoen drivers door.press lock and unlock on the vechicle lock control switch at 1 second intervals 5 times. insert key into ignition switch. switch ignition on and off twice to program a remote transmitter code whilst erasing the original codes or three timre to check how many remote transmitters are currently registered.remove key from the ignition switch.system should now lock and unlock.twice to indicate programming mode or one to four times,slowly to indicate number of remote transmitters registered.for the solara press and hold lock and unlock remote buttons together, press lock remote button for a second period of 1 second. system should now lock and unlock vechicle.once to confirm, twice to indicate registration has failed.if required repeat button procedure to program remaining remote transmitters.note to exit programming mode close drivers door or insert ignition key.maximum of 4 remote transmitters can be programmed.if akk failed let dealership reprogram remote transmitters.

May 18, 2011 | 1999 Toyota Camry Solara

1 Answer

I just bought a 1996 jeep grand cherokee larado, I locked the doo while inside with electric lock switch on door. I then opened the door with the handle. the alarm went off which I did not know it had. I...


lock with key,electric door lock button,or remote and alarm will set. to disarm you have to use the key or remote to open it.the reason it woulnt disarm from drivers door is either the door lock cylinder switch is broken or the wire to it in the rubber boot that connects the door and the body is broken.
the remotes are cheap and programing is easy,procedure in owners manuel something like lock drive door with elkect. lock switch with door open then push and hold unlock untill doors unlock then turn key off.you may have to fix that drive door lock cyl.switch first though mabee not dont know for sure

Mar 22, 2010 | 1996 Jeep Grand Cherokee

1 Answer

Power locks don't work with remote or control from


The door lock/unlock input from the driver's key switch goes to the Door Multiplex control unit (main switch), the Door multiplex control unit then sends a signal on the BUS (CAN) circuit to the passenger's multiplex control unit; the passenger's multiplex control unit then controls all the door locks. The passenger's door lock key switch inputs to the passenger's multiplex control unit, if the locks work from the passenger's side key switch but not the driver's side key switch, the most likely cause is the driver's multiplex control unit (main switch) not sending the signal to the passenger's side multiplex control unit. This could also be the drivers side door lock actuator. Hope this helps!

Jan 07, 2010 | 2003 Honda Pilot

1 Answer

Power door locks don't work with remote or manul


Look for fuse or relay problem. A bad (shorted) door lock switch can also cause trouble. Need to dig in and start looking at each component one at a time.

good luck

Feb 21, 2009 | 1994 Chrysler Town & Country

1 Answer

Door locks open by themselves randomly


some possibilities

The power door locks may self-activate or cycle on some vehicles. This may be caused by a misadjusted front door lock linkage, excess solder in the front door power window switch, water infiltration of a potential open wire harness connector inside the front doors, wiring harness chafe on the door check strap, or a damaged Remote Keyless Entry (RKE) key fob.

Nov 16, 2008 | 1996 Mercury Sable

3 Answers

Key fob not working


hello mate.. if it has stopped working you might want to check the battery first.. if you are sure that the battery is fine then consider reprogramming the fob to your car.. here are the steps to follow.. NISSAN

Remote Control Fob Procedures:

The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and emergency hazard reminders.

When the doors are locked and unlocked the unit flashes the hazard lights once for lock and twice for unlock.

A maximum of four remote controls are allowed to be programmed:

ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II

Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.

Procedure:
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Next, turn ignition switch to OFF position. Leave key in ignition switch.
3. Wait 2 seconds then the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key's.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key's for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds.


http://www.autokeysquad.com/nissan-fob-programming



i hope this can help you.. :)

Jul 28, 2008 | 2005 Nissan Sentra

1 Answer

Central locking system


I have recently had this problem I believe this to has been caused by a fault in the drivers door lock assembly It seems this contains the remote receiver. In my case I think there had been some radio interference being the main cause. The remote system seems to be working OK, The door lock will still not operate with the key.
Remove and replace the fuse 25 resetting the ignition module. Starting the engine, switch off remove the key from the ignition, stay in the car lock the doors using the door button, press and hold the remote unlock button for approx 5 seconds, listen to see if you can hear the clicking of the door receiver when you press the remote buttons. Press and hold lock/unlock button. You may be lucky.

Jun 05, 2008 | 1999 Volvo S80

Not finding what you are looking for?
2002 Dodge Caravan Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...