Question about Cars & Trucks

Open Question

Road patrol xk

Dual superheterodyne circuit

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Towing capacity of Nissan patrol ute tray top 4.2litre manual diesel


Make & Model G.C.M. Braked Trailer Toyota 70 Series 6830 kgs 3500 kgs Nissan Patrol (leaf springs) 6600 kgs 3200 kgs Nissan Patrol (coil springs) 6350 kgs 3200 kgs Beadell Tours 4WD VEHICLE TOWING COMPARISONS

Nov 23, 2016 | Nissan Cars & Trucks

1 Answer

I have a 1997 2.8l GQ Turbo charged diesel Nissan Patrol Wagon. Can you tell me what the official braked towing capacity is for such vehicle?


According to the National Roads and Motorists Association, it says it can tow up to 750 kg when it was new without brakes on load. Maybe a little more with brakes on trailer. I assume it is in very good condition. It can be a bit of a gas guzzler especially with a load.

Sep 28, 2015 | Nissan Cars & Trucks

1 Answer

Is haz-mat aloud on i-294?


Only your state's Highway Patrol would l know or the state road dept.

May 31, 2015 | Cars & Trucks

1 Answer

I have Nissan patrol super safari mod.2005, problem with fuel gauge main tank showing maximum spare tank minimum please help


if you have 2 fuel gauges working of a tank switch there may be some resistance in the circuit of the second circuit that increases the reading of the gauge. Personally I have the tanks balanced out with a levelling hose between them the the gauge reads the capacity left in the tanks IE full-- both tanks-- full, 1/2 both tanks 1/2 With the way you have it set up then if one gauge is faulty and shows full when it is empty you can find yourself in a spot of bother when you need the other tank

Nov 18, 2014 | 2005 Nissan Patrol

1 Answer

My td42 it gu y61 nissan patrol wont start when hot, replaced glow plug relay and temp sensor , will start whhen hot if you disconect temp sensor


Having the same problem mate! It's to do with the "quick glow " circuit I'm trying to find the exact control unit that is at fault

Sep 01, 2014 | Cars & Trucks

1 Answer

How to remove ring gear that is stuck on the dual mass flywheel for a patrol


Most ring gears are only shrunk fitted on the fly wheels. REmoval is by simply driving a good cold chisel in between the teeth and cracking the ring . Replacement is by heating the ringear evenly and placing onto the flywheel and letting it cool down. Ensure that any timing marks on the ring gear are in exactly the same place as the one removed. THis heating process may not work if there are sensors in the ring gear for cpu operation Check with service dealer for further info.

Feb 23, 2013 | 1989 Nissan Patrol Wagon

1 Answer

Wiggle front wheet


steering stabilizer, if all other front end parts seem ok.

May 30, 2012 | 1989 Nissan Patrol Wagon

1 Answer

How to replace a Jaguar X Type fron wheel bearing


Jaguar 2000-06

Wheel Bearings
Removal & Installation
  1. Remove the brake disc.
  2. Remove and discard the retaining clip. Detach the ABS sensor.
  3. Remove and discard the O-ring seal.
  4. Remove the wheel hub and bearing retaining bolts.
  5. Remove the wheel hub and bearing.
  6. Prior to applying sealer, clean the ABS sensor sealing surface and the ABS sensor aperture sealing surface.
  7. Install a new O-ring seal.
  8. Apply a 2.5mm bead of Loctite Ultra Blue 587 Silicone (RTV) sealer to the ABS sensor sealing surface.
  9. Install a new ABS sensor retaining clip.
  10. Install the hub/bearing assembly. Tighten to 90 Nm.

  1. Remove wheel knuckle.
NOTE When removing the wheel hub from the wheel knuckle the bearing will be destroyed and the bearing inner ring will remain on the wheel hub.
d752c5a.jpg

Fig. Using special tools, remove the wheel hub-X-Type
  1. Using special tools, remove the wheel hub.
  2. Using a suitable tool, remove the bearing inner ring.
  3. Using special tools, remove the wheel bearing.
  4. 2125147.jpg

    Fig. Using a suitable tool, remove the bearing inner ring-X-Type

    ee51ce7.jpg

    Fig. Using special tools, remove the wheel bearing-X-Type

To install:

b506586.jpg

Fig. Insert special tool 204-312 in to 204-309-X-Type
  1. Insert special tool 204-312 in to 204-309.
  2. Support the wheel knuckle on special tools.
NOTE Make sure wheel bearing is correctly orientated with the colored side facing inboard.
  1. Align the bearing over special tool.
  2. Using special tools, press bearing into wheel knuckle.
  3. Change special tool 204-312 to 204-313.
  4. Align the bearing and wheel knuckle over special tool.
  5. Slide wheel hub over the guide and align to the bearing.
  6. Using special tools install the wheel hub.
  7. Install the wheel knuckle.

  8. 5a457fa.jpg

    Fig. Using special tools, press bearing into wheel knuckle-X-Type

    b9fcc3f.jpg

    Fig. Change special tool 204-312 to 204-313-X-Type

    be319f2.jpg

    Fig. Align the bearing and wheel knuckle over special tool-X-Type

    8a9e0dc.jpg

    Fig. Slide wheel hub over the guide and align to the bearing-X-Type
  1. Raise front of vehicle and support on stands.
  2. Remove appropriate road wheel.
  3. Using wire or string, secure brake caliper to road spring to take weight off brake hose.
  4. Raise vehicle sufficient to provide access for special tool 204-111.
  5. Install special tool 204-111 in road spring.
  6. Slacken tool adjuster to suit spring length.
  7. Install adaptor and thrust collar.
  8. Position stem of tool in center of spring passing dowel through slot in suspension turret.
  9. 24ce878.jpg

    Fig. Install special tool 204-111 in road spring-XJ Range and XK Range

    1d0063e.jpg

    Fig. Position stem of tool in center of spring passing dowel through slot in suspension turret-XJ Range and XK Range

NOTE When turning tool adjuster, ensure that tool stem does not rotate and disturb position of dowel in suspension turret.
  1. Engage dowel of special tool 204-111 in suspension turret and rotate to position across slot.
  2. Lower vehicle onto stands.
  3. Rotate tool adjuster to tension spring.
  4. Remove wheel speed sensor securing screw and withdraw sensor from vertical link.
  5. Remove nut securing tie rod outer ball joint to steering arm.
  6. Release ball joint from vertical link.
  7. Install special tool 211-098 on tie rod outer ball joint.
  8. Tighten tool bolt to release taper pin from vertical link.
  9. Remove special tool from ball joint and position tie rod for access.
  10. Remove nut securing upper control arm ball joint to vertical link.

  11. 3af9a83.jpg

    Fig. Install special tool 211-098 on tie rod outer ball joint-XJ Range and XK Range

continue...

Aug 03, 2010 | 2002 Jaguar X-Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...