Question about 1993 Toyota Camry

1 Answer

Unable to open the trunk any method. I turned the key to the left and set the lock to security i have learned. How do you take it off this position?

When i try to open the trunk the key at one point turned to the left and the key hole was horizontal instead of vertical I can turn it back to vertical but no farther than that

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 41 Answers

It can only be unlocked with the master key. If you dont have one you will have to go to a Toyota dealer and they can make one for you. Bring proof of ownership tho.

Posted on Oct 27, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 784 Answers

SOURCE: can not get my trunk open by lever inside or key

The lock latch is held by a spring to be in Normal Close position. It it is in open position then there is 2 possible root causes: 1- The cable pulling the latch to open gets stuck. 2- The spring broken or out of its position. Hope this can help to fix it.

Posted on Nov 19, 2009

  • 1 Answer

SOURCE: Trunk stuck on a 03 Corolla

I was able to unlock my trunk by using a wood pole to operate the interior safety unlock handle, which is located just above the trunk floor, against the rear of the trunk lid. You simply insert the wood pole between your rear seats, while attempting to locate the handle release. When you find the handle, use the wood pole to push down on it.

Then, I had to take the top of the truck mat loose by using a flat head screwdriver to pry the plastic plug holders loose from the trunk. I also had to use a 10mm socket to loosen the trunk locking mechanism. Once inside, I notice the remote release cable ball had dislodged from its slot. I simply placed the ball in its slot and reassembled the trunk.

Problem solve. :)

Posted on Apr 04, 2010

GARYca
  • 672 Answers

SOURCE: 6/98 camry xle v6,key does not work on trunk

your trunk's lock cylinders inner rod may be disconnected, or cylinder itself is loose. These rods are held by plastic retainers, they sometimes pop out. Inspect the lock for this and reconnect.

Posted on Sep 29, 2010

  • 51 Answers

SOURCE: I am unable to open the trunk to my 2003 Toyota

try pushing down real hard on the trunk and see if the lock will move. And if it doesn't then if you aplly alot of pressure to the top of the trunk and removing it real fast such as hitting it or sitting it. It may shake the lock loose.

Posted on Jan 18, 2011

  • 752 Answers

SOURCE: Inside trunk release won't open

1. Open trunk
2. Place latch in lock position
3. Pull inside trunk release to see what isn't moving
4. If trunk key won't turn, the key may be worn out and need to be replaced

Posted on Jun 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Program the keyless entry


i guess you meant HOW CAN I program? (key word "I")
is car USA car?????? (our rules are UNIQUE)
the operators guide on all jeeps cover this.
posted this 100s of times here.
there are lots of rules related to this.
first off most newer cars, you need 2 keys to make a 3rd.
and has a 8 key limit,
and new key must be new, as used ones will not program.
tricky huh? and gets worse in time, the 2010 you cant do at all.
my 08 can do. and did.
see?
the car came with 2 keys, lost one?
that be first first.
lost operators guide, even look yet?

WJ jeep year 2000
ill read the book for you.
veh. theft security chapter.
chapter 8q in the FSM.
page 7 , "customer method"
ill see if i can paste it here, (found it in 10 seconds)

quote, real FSM
CUSTOMER LEARN METHOD
The Customer Learn feature is only available on
domestic vehicles, or those vehicles which have a
U.S. country code designator. This programming
method also requires access to at least two valid Sentry
Keys.
If two valid Sentry Keys are not available,
or if the vehicle does not have a U.S. country code
designator, the Secured Access Method must be used
to program new or additional valid keys to the SKIM.
The Customer Learn programming method procedures
are as follows:
(1) Obtain the blank Sentry Key(s) that are to be
programmed as valid keys for the vehicle. Cut the
blank key(s) to match the ignition switch lock cylinder
mechanical key codes.
(2) Insert one of the two valid Sentry Keys into the
ignition switch and turn the ignition switch to the
On position.
(3) After the ignition switch has been in the On
position for longer than three seconds, but no more
than fifteen seconds, cycle the ignition switch back to
the Off position. Replace the first valid Sentry Key in
the ignition switch lock cylinder with the second
valid Sentry Key and turn the ignition switch back to
the On position. The second valid Sentry Key must
be inserted in the lock cylinder within fifteen seconds
of removing the first valid key.
(4) About ten seconds after the completion of Step
3, the SKIS indicator in the instrument cluster will
start to flash and a single audible chime tone will
sound to indicate that the system has entered the
Customer Learn programming mode.
(5) Within sixty seconds of entering the Customer
Learn programming mode, turn the ignition switch to
the Off position, replace the valid Sentry Key with a
blank Sentry Key transponder, and turn the ignition
switch back to the On position.
(6) About ten seconds after the completion of Step
5, a single audible chime tone will sound and the
SKIS indicator will stop flashing, stay on solid for
three seconds, then turn off to indicate that the
blank Sentry Key has been successfully programmed.
The SKIS will immediately exit the Customer Learn
programming mode and the vehicle may now be
started using the newly programmed valid Sentry
Key.
Each of these steps must be repeated and completed
in their entirety for each additional Sentry
Key that is to be programmed. If the above steps are
not completed in the given sequence, or within the
allotted time, the SKIS will exit the Customer Learn
programming mode and the programming will be
unsuccessful. The SKIS will also automatically exit
the Customer Learn programming mode if it sees a
non-blank Sentry Key transponder when it should
see a blank, if it has already programmed eight (8)
valid Sentry Keys, or if the ignition switch is turned
to the Off position for more than about fifty seconds.
NOTE: If an attempt is made to start the vehicle
while in the Customer Learn mode (SKIS indicator
flashing), the SKIS will respond as though the vehicle
were being started with an invalid key. In other
words, the engine will stall after about two seconds
of operation. No faults will be set.
NOTE: Once a Sentry Key has been programmed as
a valid key to a vehicle, it cannot be programmed
as a valid key for use on any other vehicle.
end quote.

got all that?
if confused, ask any ASE shop in USA for help
they CAN DO !

Dec 13, 2015 | 2000 Jeep Grand Cherokee

2 Answers

The battery to my ford has died and i am unable to unlock my power doors?


Most cars have manual method to open doors. Put key in, turn key as far as possible, lift door handle and you should now be able to turn key further and unlock door.

Jan 24, 2015 | 1996 Ford Taurus

1 Answer

Trunk won't open


Lower the back seat and crawl into the trunk and see what the latch is doing when you activate the key fob. the trunk lid will have to be open to enable any repairs. Also an emergency release cable is probably visible (yellow handle) inside the trunk and will Open the trunk lid.

Mar 10, 2017 | 2007 Toyota Camry

1 Answer

Trunk won't open


First, if it does need an actuator, you can save some money on labor getting it done at an idependent aftermarket shop rather than the dealer. Yes, the part will most likely have to come from the dealer, but let the shop deal with that. You do not have to pay dealership labor rates. It would pay to shop around.

Second, before any parts are purchaced, the actual CAUSE of the problem needs to be verified. Unfortunately, the ONLY way to do that is to get the trunk lid open and inspect the trunk lid latch components. If none of the three methods provided by the manufacturer for opening the trunk in a normal fashion will work, the trunk will have to be accessed by removing the back seat. Once the back seat is removed, a technician can reach into the trunk and remove the bolts that secure the trunk latch to get the trunk open. The latch parts can then be accessed to disassemble, inspect, and repair accordingly.

Please note that this is the ONLY way to do this without causing further damage to the vehicle. DO NOT allow anyone to attempt getting into the trunk any other way! (Do not use pry bars or screwdrivers on the trunk lid, key tumblers, etc..)

May 11, 2012 | 2007 Toyota Camry

1 Answer

I un connected the battery to my dodge charger 06 and then reconnected it now it will not start what could be wrong with it


CUSTOMER LEARN METHOD
The Customer Learn feature is only available on domestic vehicles, or those vehicles which have a U.S. country code designator. This programming method also requires access to at least two valid Sentry Keys. If two valid Sentry Keys are not available, or if the vehicle does not have a U.S. country code designator, the Secured Access Method MUST be used to program new or additional valid keys to the SKREEM/WCM. The Customer Learn programming method procedures are as follows:
  1. Obtain the blank Sentry Key(s) that are to be programmed as valid keys for the vehicle. Cut the blank key(s) to match the ignition switch lock cylinder mechanical key codes.
  2. Insert one of the two valid Sentry Keys into the ignition switch and turn the ignition switch to the On position.
  3. After the ignition switch has been in the On position for longer than three seconds , but no more than fifteen seconds , cycle the ignition switch back to the Off position. Replace the first valid Sentry Key in the ignition switch lock cylinder with the second valid Sentry Key and turn the ignition switch back to the On position. The second valid Sentry Key must be inserted in the lock cylinder within fifteen seconds of removing the first valid key.
  4. About ten seconds after the completion of Step 3, the security indicator in the instrument cluster will start to flash to indicate that the system has entered the Customer Learn programming mode.
  5. Within sixty seconds of entering the Customer Learn programming mode, turn the ignition switch to the Off position, replace the valid Sentry Key with a blank Sentry Key transponder, and turn the ignition switch back to the On position.
  6. About ten seconds after the completion of Step 5, the security indicator will stop flashing, stay on solid for three seconds , then turn off to indicate that the blank Sentry Key has been successfully programmed. The SKREES/ SKIS will immediately exit the Customer Learn programming mode. After the ignition is cycled the vehicle may be started using the newly programmed valid Sentry Key.
NOTE: The Remote Keyless Entry (RKE) Transmitter will also be programmed during this procedure.

Each of these steps must be repeated and completed in their entirety for each additional Sentry Key that is to be programmed. If the above steps are not completed in the given sequence, or within the allotted time, the SKREEM/ WCM will exit the Customer Learn programming mode and the programming will be unsuccessful. The SKREEM/ WCM will also automatically exit the Customer Learn programming mode if it sees a non-blank Sentry Key transponder when it should see a blank, if it has already programmed eight (8) valid Sentry Keys, or if the ignition switch is turned to the Off position for more than about fifty seconds .

NOTE:
  • If an attempt is made to start the vehicle while in the Customer Learn mode (security indicator flashing), the SKREES/SKIS will respond as though the vehicle were being started with an invalid key. In other words, the engine will stall after about two seconds of operation. No faults will be set.
  • Once a Sentry Key has been programmed as a valid key to a vehicle, it cannot be programmed as a valid key for use on any other vehicle.

Jun 09, 2011 | 2006 Dodge Charger

1 Answer

ABOUT THREE MONTHS AGO I AM UNABLE TO OPEN THE TRUNK WITH THE KEY. THE KEY WILL NOT TURN WHEN I PUT IT IN THE LOCK


SPRAY WD40 IN KEYHOLE TRY ANOTHER KEY.PRESS ON TRUNK WITH HAND WHILE TRYING TURN TRUNK KEY.IN KEYHOLE.ONCE YOU GET TRUNK OPEN YOU NEED NEW TRUNK KEY LOCK CYLINDER.

Jan 18, 2011 | Toyota Camry Cars & Trucks

1 Answer

How do you open the trunk of the 1985 convertable cabriolet


the lock has 2 positions turn left/release and turn right/release.one will lock the trunk for valet parking purposes.(car comes with 3 keys,one will not open the glovebox/trunk)
please leave feedback.ta.

Sep 18, 2010 | 1985 Volkswagen Cabriolet

1 Answer

Recode a key 4 bmw 318i cenral locking


To carry out this procedure you need to have one working key and one key which requires programming. It may help sometimes to hold the key close to the rear view mirror as this is where the sensor is located in most models. 1. With both keys, get in the car and close all windows and doors. 2. Put working key into the ignition and turn to position 1 (the accessories should turn on) (try also position 2) 3. Turn the key back to position 0 and take the key out of the ignition. 4. Using the working key, hold down the unlock button, press the BMW logo (lock button) 3 times, and release the unlock button. Doors should lock and unlock. 5. With the new key, hold down the unlock button and press the BMW logo (lock button) 3 times and let go of the unlock button. Doors should lock and unlock and you're done!! If not working try the following PREPARATION 1. Close all doors, trunk, hood and sunroof. 2. The security system must be in 'disarm' mode. The key must be removed from the ignition key slot. ENTER CODE LEARNING MODE 3. Open trunk and leave it opened. 4. Open the drivers door and sit in the drivers seat. 5. Close the drivers door. 6. Cycle the ignition switch 5 times between the 'OFF' position and position 2,(ignition 'ON', all dash warning lamps will illuminate). The red status LED will illuminate continuously, and the siren will 'chirp' once, to indicate that the code-learning mode has been initiated. ?Do No start the engine.? The Ignition switch cycling in step #6 must be performed within 10 seconds. The sequence in steps #1-#6 must be performed within 45 seconds. REGISTER/DELETE ID CODE(S) 7. Open drivers door, (remain seated in the drivers seat) 8. Close the drivers door. 9. Press and release any button on the remote you wish to register in the system. The status LED will shut off momentarily to indicate that one code has been registered. 10. Repeat steps 7 thru 9 to register the three ID codes. It is possible for the system to memorize a total of 4 different ID codes. As a new code is initialized into the memory, the oldest code is automatically deleted. If you had lost your remotes and wished to delete the lost remote ID codes from the memory, you could initialize the ID codes from a newly purchased replacement transmitter four times thereby deleting the previous ID codes from the system memory. EXITING CODE - LEARNING MODE: 11. Open drivers door, and exit from the vehicle, leaving the door opened. 12. Close trunk. 13. Close drivers door. The LED will turn off and the siren will 'chirp twice. 14. The initialization procedure is now completed; Test all remotes to confirm operation. If this doent work your alarm/central lock needs to be reset

Mar 28, 2009 | 1996 BMW 318

5 Answers

Mercedes/dead battery can't open trunk help


I have the same issue (battery is completely dead in my 1998 Mercedes C280 and I can't pop open the trunk). I looked under the hood and have no idea where the positive charging post would be - can anyone help me find it? Thanks

Mar 08, 2009 | 2000 Mercedes-Benz S-Class

Not finding what you are looking for?
1993 Toyota Camry Logo

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...