Question about 2004 Chrysler Town & Country

Open Question

Where is the bank1 oxygen sensor on town and country 2004

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 740 Answers

SOURCE: I need location of oxygen sensor on a 2001 town & country

ALL of your oxygen sensors are located i your exhaust system Your exhaust system starts at the exhaust manifold on the side of the engine and ends at the tail pipe by you back bumper. Your vehicle oxygen sensors are 4 of them there are two on each side of your exhaust the are actually screw into the exhaust they are like the nose of you engine to read how rich/lean the car is running. The are pretty simple to replace, they look kinda like spark plugs with wires attached to them the wires are usually colored white black and grey with plug connections on the end. To replace get a oxygen sensor socket and a ratchet and unscrew this socket can be bought at almost any auto parts place like auto-zone etc. Good luck and thanks for using FIX YA

Posted on Mar 22, 2009

Ad
  • 6982 Answers

SOURCE: 05 town and country needs upper oxygen sensor. doe

If you can get a wrench on it, there's no reason that you couldn't change it. Make sure you put anti-seize compound on the threads before installing new one, or you will never get it out again. Be aware: changing O2 sensor often does not fix a problem as exhaust content can be beyond sensors range and will cause false trigger, caused by another item in fuel system etc.

Posted on Oct 02, 2009

  • 88 Answers

SOURCE: Bank 1 Sensor 1 - Oxygen sensor needs to be

The sensor you indicate would be on the manifold of the head containing cyl.# 1, top sensor (prior to catalytic conv.) 6 cyl. engine. 4 cylinder would be sensor on exhaust manifold. Confirm sensor failure prior to replacing as chrysler harness connectors are known for pin failures at 02 sensor connections. Inspect for burnt pins and cracked/chaffed wires first before changing sensor.

Posted on Jan 30, 2010

  • 3640 Answers

SOURCE: picture of bank1 sensor1 o2 sensor location on

I do not have a diagram but, bank 1 is the bank where #1 cylinder is at. other side would be bank #2. so bank #1 o2 sensor is just before convertor.

Posted on Aug 29, 2010

jturcotte
  • 8511 Answers

SOURCE: P0032 Oxygen sensor heater problem. This is on a

The sensor in question is behind the engine on the exhaust manifold.

You can test the heater in the sensor with an ohmmeter using the following procedure:

  1. Disconnect the electrical harness from the sensor.
  2. The white wires in the sensor connector are the power and ground circuits for the heater.
  3. Connect the ohmmeter test leads to the terminals of the white wires in the heated oxygen sensor connector.
  4. Check the resistance of the sensor, if it is not within 4-7 ohms, replace the sensor.
  5. ea87f67.gif

Posted on Oct 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2001tiburoncomputor codes, po136 & 141 what do they refer to.


P0136 = Oxygen Sensor Circuit Malfunction (Bank1, Sensor2)
P0141 = Oxygen Sensor Heater Circuit Malfunction (Bank1, Sensor2)

CHECK WIRING BEFORE REPLACING SENSORS

If 4 cylinder engine, there are only two O2 Sensors - Sensor 1 is on top, Sensor 2 is at the bottom

If 6 cylinder, there are four (4) O2 sensors (Bank1, Sensor2 is on the firewall side of this engine and is referred to as the 'DOWNSTREAM' sensor (the one AFTER the Catalytic Converter)

Aug 25, 2011 | Hyundai Tiburon Cars & Trucks

1 Answer

Error code p0032 on town and country 3.8L engine. I replaced the bank1 oxygen sensor but still have the error code and check engine light is still on. installed brand new Bosch oxygen sensor. What else...


Causes A P0032 DTC trouble code may be caused by one or more of the following:
  • A short in the heater circuit in the sensor
  • A failed O2 sensor heater
  • Wiring/connectors broken/frayed leading to sensor and/or relay
  • Failed PCM/ECM
Possible Solutions To fix a P0032 DTC code, you'll need to do a proper diagnosis. To do that, you'll want to inspect the wiring and connectors leading to the sensor. Also if equipped with a heater relay and fuse, you'll want to check those as well. Use a digital volt ohm meter to:
  • check for 12 volts at the heater circuit feed (hint: unplug the sensor and check at the wiring connector to do this measurement)
  • check the ground circuit for continuity
  • measure the resistance of the heater circuit (done on the sensor itself)
  • measure the resistance and voltage of the wiring
Refer to a service manual for the correct specifications (volts, ohms) for your vehicle. On some Toyota vehicles this code is triggered when the resistance of the heater circuit is above 10 A.
With that said, a common fix for this DTC is to replace the air/fuel (O2 oxygen) sensor #2 on bank 1.
Please keep in mind that OEM (original equipment) replacement sensors are recommended (from the dealer). Aftermarket sensors can be less reliable and of poorer quality (not always, but more often). There's also a chance that replacement parts for the P0032 code may also fall under a federal emissions warranty (check with your dealer to see if it's covered).

Jun 29, 2011 | 2004 Chrysler Town & Country

2 Answers

Engine fault codes: P1684 P0135 P0456


Hi the p1684 means the battery has been disconnected within the last 50 starts, the P0135 is Oxygen O2 Sensor Heater Circuit Malfunction (Bank1, Sensor1), you may have notived an increase in fuel consumption. and the P0456 code means evaporated emissions system -small leak detected the causes could be either A small leak in any of the EVAP hoses or fuel tank hoses, a small leak in the purge valve or vent valve or the EVAP Canister may be leaking
Hope this helps
Steve

Mar 02, 2011 | 2002 Chrysler Town & Country

1 Answer

P0032 Oxygen sensor heater problem. This is on a 2004 Chrysler Town and Country 3.8 L V6.


The sensor in question is behind the engine on the exhaust manifold.

You can test the heater in the sensor with an ohmmeter using the following procedure:
  1. Disconnect the electrical harness from the sensor.
  2. The white wires in the sensor connector are the power and ground circuits for the heater.
  3. Connect the ohmmeter test leads to the terminals of the white wires in the heated oxygen sensor connector.
  4. Check the resistance of the sensor, if it is not within 4-7 ohms, replace the sensor.
  5. ea87f67.gif

Oct 24, 2010 | 2004 Chrysler Town & Country

1 Answer

How do I change the oxygen sensor


Locate the faulty oxygen sensor in the exhaust system, disconnect the electrical connection, and then you will either need the correct size box wrench or oxygen sensor socket(available at most part stores) to remove the sensor. I recommend either warming up the exhaust system a bit and being careful not to get burned or using liquid wrench to help loosen it up. Installation is the reverse. Just make sure you remove the correct sensor, these new vehicles often use more than one oxygen sensor.(bank1 is driver's side, bank2 is passenger's side, sensor1 is before the catalytic converter, and sensor2 is after the catalytic converter)

Sep 21, 2010 | 2003 Chrysler Town & Country

1 Answer

Picture of bank1 sensor1 o2 sensor location on 2001 chrysler town & country


I do not have a diagram but, bank 1 is the bank where #1 cylinder is at. other side would be bank #2. so bank #1 o2 sensor is just before convertor.

Aug 29, 2010 | 2001 Chrysler Town & Country

1 Answer

O2 sensor code po138 is it something a handy but not car savy person replace?


P0138 - O2 Oxygen Sensor Circuit High Voltage (Bank1, Sensor2)
The Heated Oxygen Sensor (2) located rear of catalytic converter produces an output signal relative to oxygen storage capacity of catalytic converter. Ho2S 2 signal is less active than signal produced by front oxygen sensor. This code sets when HO2 Sensor voltage is greater than 999 mV for more than 2 minutes (time depends on model. Could be as high as 4 minutes)

Symptoms: There may be no noticeable symptoms except for MIL illumination. Possible high fuel pressure can over rich the system.


Causes: A code P0138 may mean that one or more of the following has happened:
  • Faulty O2 sensor
  • Short to battery voltage in O2 sensor signal circuit
  • High fuel pressure (not as likely)

Possible Solutions, here are some potential solutions:
  • Replace O2 sensor
  • Repair short to battery voltage in o2 sensor signal circuit

Hope help with this (remember comment and rates this).

Jul 22, 2010 | 2005 Chrysler Town & Country

2 Answers

Oxygen sensor1 bank1, need to be location


the first one on the right hand side before the catalytic converter

Mar 13, 2010 | 2001 Chrysler Town & Country

3 Answers

How to locate the oxygen sensor in a LEXUS LS430 (Bank1 Sensor1)


the O2 sensor for bank one sensor one is located between the catalytic converter and the engine in the exhaust head pipe. see photo of your engine cylinder layout, the sensor u want to replace is the one at the cylinder #1 0aa2e73.gif bank on right.

Apr 15, 2009 | 2001 Lexus LS 430

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...