Question about 1992 Buick Century

Open Question

Reset crank sensor in 1989 buick century 3.3 - 1992 Buick Century

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jeffk14
  • 16 Answers

SOURCE: how to replace a coolant level sensor, 2000 buick century

TRY THIS. Good luck!

Posted on Nov 22, 2008

Papa Chan
  • 56 Answers

SOURCE: how to replace a coolant level sensor, 2000 buick century

The coolant level sensor is located on the radiator. If you are looking at the engine from the front of the car it will be on the left side. There will some kind of clip holding it in the radiator. Removed the clip and pull the sensor out. You will lose coolant so try to swap it out quick or drain some of the coolant out. Once new sensor is installed, install clip to keep the sensor in place and reconnect the wires to the sensor. Crank the engine and make sure the coolant level is full. This should correct your problem.

Posted on Jan 04, 2009

  • 59 Answers

SOURCE: where does the flasher plug go on a 1989 Buick

you probably have two flashers. try to remember where you heard the tick. turn your emergency flasher and locate that by feel. the one your looking for should be next to it. however the could one in the same. go to your local parts store and look at the manual that has been opened for your vehicle.

Posted on Apr 26, 2009

  • 36 Answers

SOURCE: locate crank sensor on 1990 buick century

Hello, the crank position sensor or (CPS) censor is located directly behind the harmonic balancer (or fly wheel at the very bottom). The sensor is located on the right side of the harmonic balancer when facing the front of the motor. You must remove the harmonic balancer to replace the sensor. You must also re-align the sensor with 30 thousands of an inch tolorence, or your car may idle rough or may not start. I own a 1990 Buick Century and just replaced my CPS sensor last month. There is a trick I learned to reinstalling the new sensor. Let me know if you need that information.

Posted on May 28, 2009

  • 17 Answers

SOURCE: buick century 1993 stalls while driving

i had the same problem with my 92 exept after mine stalled it wouldnt start for 20 - 30 mins... mine ended up needing a transmission flush for the stalling problem and i tried to drive everyday that helped
hope this helps in some way

Posted on Jun 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 buick century station wagon no spark cranks but does not turn over... changed coil pack, Control module, brain,spark plugs wires...any ideas


I'm not sure of engine Size? Did you check the crank sensor? Any applicable trouble codes? Do you have a fuel injector pulse, engine cranking?

May 24, 2015 | 1989 Buick Century

2 Answers

Check crank sensor 2000 buick century


Click the link mentioned below:---

How to test Crankshaft Position CKP Sensor?

--------------

Crankshaft Position Sensor Operation?

-------------------

These will help.

Thanks.


Dec 06, 2012 | 2000 Buick Century

1 Answer

I need to know where a crank sensor is located on a 1995 buick century?? And also need to know where the cam sensor is located


Crank sensor is in back of harmanic pulley (crankshaft), and camshaft sensor is on front of timing chain cover.

Aug 19, 2010 | 1995 Buick Century

1 Answer

I need to know what size wrenches are needed to replace harmonic balancer and crank sensor on my 1989 buick century 2.8 ltr. engine


you will need sockets,the crank bolt i belive is 22mm and you might need in impact wrench to remove bolt. the crank sensor is 1/2 in or 13mm, that a rachet is good.and to remove balancer sometimes youll need a puller. hope this helps.

Oct 13, 2009 | 1989 Buick LeSabre

1 Answer

Where is the ECM located on an 1989 Buick Century Custom V6 3.3 l


unhook the battery for about 15 minutes... that will reset it ... if the stereo is an anti theft type... make sure you know the code and how to enter it.

Mar 18, 2009 | 1989 Buick Century

2 Answers

MAF Sensor location on a 1989 Buick Century


you cant clean it it wont help need to replace if it is acting up it is located on top of the throtle little square black box with 4 or 5 wires

Feb 13, 2009 | 1989 Buick Century

Not finding what you are looking for?
1992 Buick Century Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...