Question about 2004 Nissan Frontier
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: brake light switch
IT WAS LOCATE IN UPPER OF THE BRAKE PEDAL
BEFORE YOU CHANGE IT CHECK FOR :-
STOP LAMP SWITCH AND ASCD CANCEL SWITCH CLEARANCE
1. Twist and pull to remove switch.
2. Pull up on brake pedal pad and hold.
3. Insert switch into retainer until switch plunger is completely depressed.
4. Turn the switch until it locks into place in the brake pedal bracket.
When turning the switch to lock into place, the switch backs off the stopper to the correct clearance automatically.
5. Release the brake pedal pad.
ASK ME FOR MORE ??
WITH MY BEST WISHES
Posted on Jul 23, 2008
the plastic around the gear shifter will pop up with a good pull, then turn it side ways to get over the shifter, then there are 2 screws the hold the bezel down around the radio and air vents, then just pull from the air vents it will pop off to reveil the screws to the radio
Posted on Feb 27, 2009
SOURCE: 2004 nissan titan, shift lever
Thank you for choosing fixya.com.
First things first: I suggest taking your truck to a mechanic or an auto parts store that can do a diagnostics test done. If any fuses or relays are blown, this test should bring up any codes that would indicate any type of malfunctions.
The shift lever being locked: In newer vechicles, the brake pedel, as you know must be pressed in order for the transmission to be put into gear. There should be a sensor on the transmission that runs in cahoots with the brakes. This sensor tells the computer what gear the transmission is in. It is very possible that at the last time you put the vehicle in Park, that the switch had it's final moment of ability. If the sensor is in fact useless, it may be the reason the transmission is locked into Park. It may be the reason why the brake lights aren't working; and why the brake lights fuse is blowing. Also, check all relays, (can be tested with a fuse tester) and make sure all relays are good as well. Make sure also that the light sockets for the brake lights, tail lights, back up lights, and front running and blinker lights are in good condition. One faulty socket, can cause more than one bulb to blow, or cause fuses and relays to blow as well. Follow the wiring for the brake lights for as far as you can to ensure there is no damage (melted, broken, etc.). This could also affect fuses. This truck I see is barely 5 years old, but you'd be surprised how quickly parts and wiring and such will go bad, or wear out and/or just quit working.
If the transmission sensor is not the problem, and all fuses and relays are good. tranny fluid is full, check the linkage under the truck. It may be jammed somehow, or stuck. On the transmission, where the lever inserts, there is a seal - inside that seal, there is like a gear that the lever pushes in order to shift from gear to gear etc. You may need to have that checked out to make sure it's not broken inside. If your fluid is low, or empty, you may have froze up your transmission, however, you most likely would have been seeing large amounts of fluid in the frequent places you park. Another think to check is your differentials. Make sure the fluid is full in each, as well as the seals not leaking. The seal sits just inside the inner most part of the pumpkin (differential ball) where the yoke is inserted. Maybe you have just locked up the rear driveline. Check the seal on the front end of the driveline as well, (goes into the rear of the transmission (yoke). Check your U-Joints as well, making sure they are intact, tight. It may be a good idea to have them replaced if they look supsicous in any way.
These are all the things I can think of that would make your truck be stuck in park, and make your lights not work, and blow fuses.
I sincerely hope this information is useful and aides in the successful repair of your truck. Thank you again for choosing fixya.com. Please let me know if I can be of further assistance, or if you have any more questions or concerns (comments).
Thank you again,
Posted on Apr 06, 2009
look up above your brake pedal and you should see the switch. Depending on the car, the switch either pops out, or just needs a screw to be removed
Posted on Sep 16, 2009
The entire bed line will need to be removed. The long screws that hold the metal bracet where the bed extender attaches also hold the tail light assembly in place.
I pulled the bed liner up at a 45 degree angle and layed it on top of the cab. This revealed the screws. Take both screws out and lay to the side along with the metal bracket for the bed extender.
Now firmly grab the edges of the tail light assembly and pull...there are 2 hard rubber nipples that snap in to hold the assembly. You will feel like you might break it but you won't..just pull straight back hard. The assembly will "POP" out and then you can just twist the back of each bulb there are (3) and pull out..now you will see the bulbs..just pull the bad bulb straight out and push the new one into place. Now just reassemble. Total time will be 30-45 min. for this repair.
Posted on May 04, 2010
Tips for a great answer:
Jun 05, 2015 | Nissan Hardbody Cars & Trucks
Feb 19, 2015 | 2004 Nissan Frontier XE
Apr 07, 2014 | Nissan Cars & Trucks
Oct 02, 2012 | Cars & Trucks
Sep 10, 2010 | 2007 Nissan Frontier SE Crew Cab
May 19, 2010 | 1998 Nissan Frontier
Oct 08, 2009 | 2004 Nissan Frontier
Mar 16, 2017 | 2005 Nissan Frontier
75 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: