Question about 2006 Toyota Sequoia

Open Question

License plate bulb replacement

How do you remove the license plate bulb on a 2005 Toyota Sequoia?

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 65 Answers

SOURCE: I have a 2004 Toyota

You have to remove the rear door inside panel.First thing is to remove the top and side interior trim panels,they just pop out by prying them away after they are out the metal retaining clips sometimes stay in the door,pull them out and put them on the plastic panel before reinstalling.Then the strap that you use to close it has a cover on it that you have to push up to get off then remove the 10 mm bolt that holds the strap.Then pry the panel away from the door I think that the bottom has two hooks on it which means that the top needs come off first so you can lift the panel hooks out of the slots.Once the panel is off you will see the bulbs they twist out and you have to pull the bulbs out.Good luck

Posted on Nov 29, 2008

  • 840 Answers

SOURCE: 2002 license plate bulbs

its real simple look at the license plates then look up you will see 2 screw per lamp / unscrew them and slide remove its a 194 bulb so get some ready then replace and put back / Please rate my response thank you very much

Posted on Feb 02, 2009

  • 4977 Answers

SOURCE: Do you have illustrations or

there should be 2 screws that hold the light lens in place,that you take out to get to the bulbs,once the lens is removed.if the lights are in the trunk tailgate and there is no screws then with the trunk lid open and you look inside above the area the lights you should see the bulb sockets that you turn a 1/4 turn to remove the socket to replace the bulbs.

Posted on Apr 14, 2011

  • 5370 Answers

SOURCE: License Plate Light Replacement: How

Its not very hard, to replace.---- First remove the clips on the trunk lid liner. To remove clips, hold the outer rim of the clip with your fingers and turn the center with a #2 phillips screwdriver. The center part will loosen, then pull the clip out by the center piece.

Once the trunk pad is off, you need to twist the light bulb connector and remove the bulb connector out.Then remove old bulb and insert the new bulb and reverse the procedure.---------
Click this link below and follow the procedure with more detail:--- http://technoanswers.blogspot.com/2011/07/how-to-remove-licence-plate-bulb-on.html ---------- This should help.Thanks.Helpmech.

Posted on Jul 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Plate light does not work, but lights are good and sockets seem good


check bulb the number plate light runs on the same circuit as the side lights so if they are working its got to be a bad earth on the plate light

Jan 24, 2016 | Cars & Trucks

1 Answer

Remove license plate bulbs from casing 2003 toyota echo


twist the fitting should come apart maybe tight

Apr 07, 2014 | 2003 Toyota ECHO

2 Answers

Where is the fuse box loacted on a 2005 toyota corolla.... my two back license plate blubs blew and I want to replace them but cant find the fuses.


The fuse box should be located by your right leg near the bottom of the dashboard. There should be an access panel that un clips and allows you to access all the fuses for the interior and exterior lighting.

Mar 22, 2011 | 2005 Toyota Corolla

1 Answer

How do I replace the rear handle for the 02 sequoia


you need to remove the back door cover panel then the 15 bolts holdin the cover plate the remove the license plate and the rear window and glass then you can access the panel that holds the handle

Feb 27, 2010 | 2002 Toyota Sequoia

2 Answers

Need to replace license plate bulb on my 2005


1. Open the hatch and stand under it.
2. Remove pull handle from the inside of the hatch (2 screws under pop panels).
3. Starting in the lower corners, gently pry the entire interior panel from the hatch,
and leave it hanging from the wiper area near the glass.
4. Grasp the bulb housing and twist to the left while pressing inward.
5. Replace with a 1156 bulb.

Nov 01, 2009 | 2005 Nissan Pathfinder

2 Answers

Back door handle broke.how do i get the cover off to fix it to open it again?


use a long screwdriver, approx 8in and skinny. Under the handle you will see the broken part on the right side. remove that part and insert screwdriver striaght up as possible, then point down to push lever inside door. REMEMBER to unlock doors first, after inside panels removed and license plate, you can remove the license plate box and replace handle

Oct 19, 2009 | 2003 Toyota Sequoia

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

1 Answer

I need to remove 2004 toyota sequoia tailgate door panel to get access the rear tail light to install a backup camera. I don't see any obvious removal points.


Slide the plastic cover off the tailgate ******** the passenger side to reveal a 10mm bolt.

Remove the bolt and the strap/

Using a flat prying instrument, remove the center trim section one the inside of the tailgate above the window.

Grab the top edges of the side trim sections on the inside of the tailgate and pull down to remove.

Using a flat instrument, pry at the bottom edge of the tailgate main trim panel, it is held on with about 12 plastic pop-in fasteners so it will take several 'pops' before it is released.

Behind that there is a metal access cover the width of the tailgate, held on by ~5x pop in fasteners and ~10x 10 mm bolts. Remove the bolts and pop the panel loose, it will hang by the wiring so support it while you do your camera work :)

The license plate trim panel, should you need to remove it, requires remoaval of the license plate.

Then remove ~3x 10mm bolts from the top of the panel, accessed from the inside.

Using long needle nose pliers compress the pop-fasteners holding the lower corners of the license plate trim panel on, being careful not to let it drop and slide down the vehicle, scratching the paint :)

Sep 20, 2009 | 2003 Toyota Sequoia

1 Answer

My 2004 Toyota Sequoia rear door will not open - the handle is broken. How do I get into the door, whith it closed, to make the necessary repairs?


Dig out the broken bits of door handle, then on the right side insert a flat head screwdriver diagonally up and fish around for the release lever.
Push up on the screwdriver handle to manipulate the release lever down and your tailgate will open.
Remove the interior panels by unbolting the 10mm bolt behind the strap and pulling off the interior pieces held on by plastic pop fasteners.
Remove the 10mm bolts around the perimeter of the interior cover plate and let it hang by the harness.
Remove the license plate.
Remove the license plate trim panel (multiple push fasteners from behind and a few 10mm around the lock)
Replace the handle.

Sep 13, 2009 | 2004 Toyota Sequoia

1 Answer

2002 license plate bulbs


its real simple look at the license plates then look up you will see 2 screw per lamp / unscrew them and slide remove its a 194 bulb so get some ready then replace and put back / Please rate my response thank you very much

Feb 01, 2009 | 2002 Toyota Avalon

Not finding what you are looking for?
2006 Toyota Sequoia Logo

Related Topics:

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...