Question about 2000 Mazda MPV

Open Question

2000 mazda mpv wont stay running if you keep your foot on the gas it will run but when you take it off it dies

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chiquititas
  • 1010 Answers

SOURCE: mazda 96 626

maybe the starter or wire connections are bad? see if theres a way to turn the engine manually so you know it's not locked up...make sure the spark plug wire is off!

Posted on Jun 29, 2008

SOURCE: Idle Speed dies

I have a 1995 Mazada 626 V6 and i had a simular problem. My mechanic couldn't figure it out. My boyfriend did the usual checks also, but 1 thing extra he raised the idle to 1100-1200 rpm's from the 750-1000 it was at...well since then no problem.
good luck

Posted on Apr 08, 2009

  • 1 Answer

SOURCE: the fan motors keeps running after car is shut off. Also sometimes fans start when car is started cold.

I had the same thing happen to me...fans would run even when car turned off. Was the thermostat. Got one with high temp-92* I think, it did the trick!

Posted on Jun 23, 2009

jeffpresnail
  • 42 Answers

SOURCE: mazda mpv lx 2000- remote control not responding

Does the remote do anything at all? Lock/unlock doors etc.? If not it's likely that the remote needs to be reprogrammed (can be done easily with online instructions) or the obvious: the battery is dead.

Posted on Aug 11, 2009

  • 10 Answers

SOURCE: how do I replace alternator in mazda mpv 2000?

Typically an alternator is an easy fix. It requires removal of the belt from the engine running it, and a few bolts that attach it to the engine.

Because of the engineering with the 2000 mpv, it is a very difficult fix, and one that requires removal of the transaxle and exhaust manifold, as well as removal of the lower engine mounts. It will take a qualified Mazda mechanic 3.5 hours to do the fix - you can (at least) triple that amount of time as a DIY project (assuming you have the right tools).

Posted on Nov 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Won't stay running


are all the spark plugs have spark

Feb 17, 2014 | 1991 Mazda 626

1 Answer

Fuel pump relay


check the idle air control valve . it might be need to clean /..

Sep 28, 2013 | 2003 Mazda MPV

1 Answer

TRUCK BATTERY DIES,STARTS WHEN JUMPED BUT WONT STAY RUNNING WITHOUT FOOT ON GAS


Some models have to be retaught how to idle once the battery dies, so you need to start the truck and feather the gas peddle to keep it running and do this for a few minutes, the computer has to relearn how to idle the engine.

Oct 04, 2012 | Cars & Trucks

1 Answer

2000 MAZDA MPV TURNS OVER BUT WONT START. RAN FINE YESTERDAY. GOT IT TO START TODAY AFTER HOLDING GAS PEDAL DOWN BUT NOW ITS PUTTING OUT.


Sounds like you possibly got bad gas, or your at the bottom level of your gas tank and got the nasty stuff. Try running a good fuel treatment through the system and fill it up with premium gasoline from Marathon

Feb 10, 2012 | 2000 Mazda MPV

2 Answers

I have a mazda mpv 2000 minivan.problem code p0301 misfire detected cylinder#1


I'd check #1 spark plug.
Usually a misfire code "fix" is a spark plug, spark plug wire, or a coil pack / distributor.
Keeping it simple...I'd go with the spark plug first and then look at the condition of the wires.

Hope this helps...

Aug 28, 2011 | 2005 Mazda MPV

1 Answer

Starts but wont stay running. You have to keep your foot on the gas to keep it running


This sounds like a problem with the idle control. The idle control has to be adjusted. If it's not an idle control, then it would help to know the year, make and model of the car and the mileage on the car. At the simplest, it's the idle control. However, it may also be a problems with the car's ECU.

Dec 30, 2009 | 2000 Mazda MPV

1 Answer

Check Engine light code 1506 for 2000 Mazda 626


Here is some problem in your car wiring, some of the jack is lose or unplug near relay box,

Sep 16, 2009 | 2000 Mazda MPV

1 Answer

Engine wont stay running


you're running rich, the cylinders get flooded with fuel and won't fire. stepping on the gas blows out the excess fuel. take it to the dealer and have the mixture adjusted.

Jan 10, 2009 | 1994 Lincoln Mark VIII

Not finding what you are looking for?
2000 Mazda MPV Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...