Question about 2007 Peugeot 307 1.6

Open Question

Peugeot 307 fault code p2006 - 2007 Peugeot 307 1.6

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: peugeot 307 heater blower fault

Hi
i just had the same fault, but being in the trade it is normally only 1 of 2 problems.
the heater resitor packing up or the wiring loom.
both can be bought through peugeot.
try the heater resistor first (£40). to find it undo 7 star screws to remove glove box then look in behind centre conlsole near back of radio diconnect the black plug with a red and black cable. twist back of fan motor clockwise and remove fan(it's a bit of a tight squeeze to remove),then put your hand inside the hole you just made till you feel the flat resistor turn this anti-clockwise and disconnect green plug then reassemble as removed,

if this does not fix it then it is the loom, to remove this it is best to follow the wires from the back of fan motor up to where i think if i remember lead to 2 other plugs 1 green and 1 black on the way to another green plug up behind the drivers foot well, then thread the new loom back the same way.

on the 405 i think the resistor is in behind the fan motor accessed throgh the driver side footwell again you need to first take out the fan motor normally twisted anti-clockwise. it is un common for 405 to burn out heat resistors it is normally down to a wire fault.

hope this helps

Posted on Jan 18, 2009

Ad
  • 205 Answers

SOURCE: "when do i change the cam belt on a peugeot 307 sw diesel"

usually you should do it for peugeot diesel at 122000 miles along with water pump and the tensioner roller that runs under the cambelt too. But to be on the safe side do it at 100000 and save the fortune.
It took me (DIY job) about 6-8 hours as i wanted to save 450 pounds.

Posted on Sep 04, 2009

alicantecoli
  • 22246 Answers

SOURCE: Peugeot 307 power steering not working, but if I

electric pump or engine driven

Posted on Oct 30, 2009

  • 583 Answers

SOURCE: Peugeot 307 diesel 307 - Unblock diesel filter

if it says the diesel filter, then that is what it means,a fuel filter.normal service requirement on any vehicle and can be done for small dollars at any garage

Posted on Dec 04, 2009

  • 6 Answers

SOURCE: peugeot 307 1.6

peugeot and citreon cars do bite high generaly, it is hydaulic there is no adjustment. but it also depends on how high it is ?? does it slip if you slightly rest your foot on whilst driving?? they do have a problem with the bearings going through the cover as it is the same bearing as a HDI . but you woud notice this as a different problem. ie noise or vibration on pedal. call me for more info .. paul @ the clutch centre..01527 64440 07790438337

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 peugeot 307 diesel fault code I509141 can you tell me what it is please.


Sorry but that is not an ODB fault code. If it is 1509 then that is Idle Control System problem

Jun 11, 2017 | Peugeot Cars & Trucks

1 Answer

How to fix an electrical circuit fault on peugeot 307


Test charging circuit (usually for free at parts store). A battery getting drained can cause much of this. With car sitting still you could try removing fuses one at a time to see if there is an unusual draw.

May 11, 2016 | 2006 Peugeot 307 1.6

1 Answer

Getting message economy mode active how do I fix this on Peugeot 307


run the fault codes and fix faulty sensor. Normally economy mode is overdrive so it may be just an indication that over drive has cut in.

Jan 15, 2015 | Peugeot Cars & Trucks

1 Answer

Peugeot 307 fault codes


code p2144 refers to exhaust gas recirculation (EGR) vent control--circuit low===causes wiring short to ground--EGR vent control.
Check the condition of the wiring and if ok then replace the vent control

May 11, 2014 | 2005 Peugeot 307 1.4

1 Answer

Engine light stays on


check oil and coolant levels first . Have the fault codes read to find which sensor activated the light as it can be engine or transmission . When you have determined the fault and had it fixed then reset the light with a code reader.

Mar 01, 2014 | 2001 Peugeot 307 2.0

2 Answers

PEUGEOT 307 FUSE KEEPS BLOWING (abs faults, horn doesnt work)


i have a peugeot 307 number 8 fuse keeps blowing so i have to keep changing the 20 amp fuse please help me i am trying to find out what is causing this

Dec 07, 2012 | 2002 Peugeot 307

1 Answer

307 fuel fault blocked filter and pollution fault on dash HELP


Try disconnecting your battery , this should reboot it and remove the code .

Jul 26, 2009 | 1987 Peugeot Liberte

Not finding what you are looking for?
2007 Peugeot 307 1.6 Logo

Related Topics:

819 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...