Question about 2005 Ford Bantam 1.3i

Open Question

Removing ford bantam power steering pulley - 2005 Ford Bantam 1.3i

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tepfy
  • 319 Answers

SOURCE: power steering pump

you need to start by getting a chilton or haines manuel, also a 3 prong wheel puller.

The maneuls will tell you what needs to get moved out of your way to get to the pulley. Pulling the pulley is relatively simple, you put the puller on and then use a wrench or rachet and pending on how much room you have. and it will do the work for you. The hard part is getting to the pulley and getting everything out of your way. Sorry I can't be more helpfull but your answer is not an easey one. You have a front wheal drive car with a 6 cylinder in it, and its a tight place.

Posted on Jul 15, 2008

Ad
  • 1 Answer

SOURCE: Removing the steering pump pulley

Don't use a standard bearing puller it doesn't work and may damage the pulley. I went to a local parts store "Salvo" and they had a Ford Power Steering Pump Pulley puller. It works. It seems like you have to put as so much force into it that something would break, but no, it just starts to come off, worth all of the 17.00 I put into it.

Posted on Jul 30, 2008

SOURCE: Power steering pump leak

replace the pump . the pulley takes a special tool you should be able to rent one at autozone

Posted on Oct 04, 2008

dennymulford
  • 1055 Answers

SOURCE: 97 ford taurus power steering pulley

pull the pully back off ,clean the shaft with emery cloth and also the the shaft hole in the pully then grease it up and try it again

Posted on Mar 14, 2009

REDOIL
  • 355 Answers

SOURCE: power steering pulley on ford escort van 92 has

you will need power steering pully puller you can rent them at most of your local part house or you can buy them there you will need to pull of belts then the pully hope this helps

Posted on Sep 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My key remote stop functioning on ford bantam had the key checked it is fine where will i find the reciever on the wiring factory fitted


The receiver wraps around the ignition switch. You have to remove the steering bezel to access it.

Sep 04, 2016 | 2008 Ford Bantam 1.6i

1 Answer

What size fan belt for ford bantam 1.3 2004 no aircone no power steering


When you go and buy a new belt thay will ask for the cars registration number job done ps have you checked the belt has broken

Aug 27, 2014 | 2005 Ford Bantam 1.6i

2 Answers

How do i take off the pulley off the power steering ?


The power steering pulley is pressed on, as paul said you will need a power steering pulley puller tool, you can borrow from a parts store. This tool is used to remove the pulley and also install it back onto the pump.

Mar 02, 2012 | 2002 Ford Taurus

1 Answer

How do i change a power steering pump on a 2004 ford f 150 5.4 4x4


p, li { white-space: pre-wrap; }


Follow this steps


The items you will need include basic hand tools, shop rags, gloves, drip pan, fluid suction gun, power steering pump pulley removal tool, power steering pump pulley installation tool, power steering fluid, and a Haynes manual.


Use a suction gun to remove the power steering fluid.


Position a drip pan under the pump and disconnect the high pressure line and fluid return hose. Cap the ends of the lines.


Loosen the serpentine belt and slip it out of the power steering pump pulley. Replace any worn belts at this time.


Remove the bolts and nuts that hold the pump onto the engine.


Remove the pump. Now remove the pulley from the pump. To do this, use a power steering pump pulley removal tool. If you don't have one, you can rent one from Advance Auto Parts.


Remove the nuts to detach the pump from the brackets.


Reattach the bracket to the new pump. Reinstall the pulley.


Bolt the pump back into place. Slip the belt back onto the pulley and retighten. Reattach the high pressure line and return fluid hose.


Now fill the power steering fluid reservoir until it reaches to the proper level. Now start the vehicle. Recheck the fluid and add if necessary. Turn the wheels left and right a couple of times. So that's it, you are done. Test the vehicle to make sure it functions properly.


Aug 27, 2010 | 2004 Ford F150

2 Answers

Where is the power steering dipstick


Most power steering pumps are driven by the serpentine belt and should be in plain view when the hood is open.The following shows how to remove and replace the power steering pump and might give you a clue if not in plain sight. My dad's 1998 Ford Taurus has it nearly on top, but they could have changed things in the mean time: Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Remove the alternator.
  5. Drain and remove the radiator coolant recovery reservoir.
  6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  7. Remove the idler pulley from the power steering pump support.
  8. Remove the belt tensioner.
  9. Remove the bracket mounting bolt located under the belt tensioner mounting.
  10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  11. Clamp the pump support bracket in a suitable vise.
  12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.
To Install:
NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.
Power steering pump special tools ford-08-00-401.gif

  1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
  4. Install the bracket mounting bolt located under the belt tensioner mounting.
  5. Install the belt tensioner.
  6. Install the idler pulley to the power steering pump support.
  7. Connect the hydraulic pressure and return lines.
  8. Install the radiator coolant recovery reservoir.
  9. Install the alternator.
  10. Install the accessory drive belt.
  11. Fill the power steering reservoir with power steering fluid.
  12. Connect the battery ground cable.
  13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.
Power Steering Pump (4V) and SHO To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Drain and remove the radiator coolant recovery reservoir.
  5. Position a drain pan under the power steering pump. Disconnect the power steering pump reservoir hose and allow it to drain.
  6. Using Pulley Remover T69L-10300-B, or equivalent, remove the pulley from the power steering pump shaft.
  7. Disconnect the pressure hose from the power steering pump and allow it to drain.
  8. Remove the power steering pump retaining bolts and the pump.
To Install:
  1. Install the power steering pump and tighten the bolts 15–22 ft. lbs. (20–30 Nm).
  2. Connect the pressure hose and secure the clamp.
  3. Using a Steering Pump Pulley Replacer T65P-3A733-C, or equivalent, install the power steering pump pulley: the pulley face must be flush with the pump shaft or within 0.010 inch (0.25mm).
  4. Connect the power steering pump reservoir hose.
  5. Install the radiator coolant recovery reservoir.
  6. Install the accessory drive belt.
  7. Fill the power steering reservoir with power steering fluid.
  8. Connect the battery ground cable.
  9. Start the engine and check for leaks and proper operation. Bleed the power steering system if needed.
prev.gif next.gif

Jul 22, 2010 | 1996 Ford Taurus

1 Answer

Power steering pulley on ford escort van 92 has


you will need power steering pully puller you can rent them at most of your local part house or you can buy them there you will need to pull of belts then the pully hope this helps

Sep 28, 2009 | 1992 Ford Escort 4 Door

1 Answer

Removing the steering pump pulley


Don't use a standard bearing puller it doesn't work and may damage the pulley. I went to a local parts store "Salvo" and they had a Ford Power Steering Pump Pulley puller. It works. It seems like you have to put as so much force into it that something would break, but no, it just starts to come off, worth all of the 17.00 I put into it.

Jun 29, 2008 | 1998 Ford Mustang

Not finding what you are looking for?
2005 Ford Bantam 1.3i Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...