Question about Cars & Trucks

Open Question

Vr commodore 3800 intake manifold torque pattern

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Torque and sequence to Intake Manifold for 3.3L Nissan Xterra 2000

Hi El Faraon,
I believe that you're dealing with 12 mm bolts and nuts....THESE ARE NOT THE SPECS FOR YOUR ENGINE, but I believe that if you use them you'll be close....Tighten in three stages up to 22nm....choose the bolts from the centre of the manifold and circle outwards until you reach the last one.....It may be a good idea to draw an overhead or plan view of the unit, marking out the bolt positions.....Start at the centre and mark the sequence and follow that....What is important is starting at the centre, so that nothing becomes warped....

Hope this helps,

Regards, Johngee10

Posted on Sep 06, 2008

Ad
LT1Rob
  • 55 Answers

SOURCE: Torque Spec for '99 Chevy C1500 5.7L engine lower intake manifold

On 5.7L engines, install the bolts and torque in sequence as follows:

  1. Step 1: 71 inch lbs. (8 Nm).
  2. Step 2: 106 inch lbs. (12 Nm).
  3. Step 3: 11 ft. lbs. (15 Nm).
f2266b6.jpg

Posted on Mar 14, 2009

  • 1201 Answers

SOURCE: Torque Settings for 3.4L DOHC Intake Manifold and Plenum

10 ft lbs.

Posted on Mar 16, 2009

chuck943
  • 783 Answers

SOURCE: Ford 460 Intake Manifold Torque spec

22 to 35 ft lbs

Posted on May 22, 2009

outdoorsman5
  • 631 Answers

SOURCE: head bolt torque specs for 2000 dodge neon 2.0 SOHC

I have the specs and diagrams. If you want me to send them to you, give me your email address. Outdoorsman592003@yahoo.com

Posted on Sep 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 buick century torque prints for haeds on up


the 3100 specs
Type: Bolt Dim: Length: Head: Hexagon Grade: 37 Ft-Lbs 444 In-Lbs 50.17 N-m Connects: Cylinder Head To Engine Block Years: 1998-2001 Vote Record: Vote Note: 3100 - Head Bolts - 2 Steps: 37FtLbs; +90deg
12 Ft-Lbs 144 In-Lbs 16.27 N-m Connects: Exhaust Manifold To Cylinder Head Years: All Vote Record: Vote Note: 3100 - Exhaust Manifold to Cylinder Head
Type: Bolt Dim: Length: Head: Hexagon Grade: 9.58 Ft-Lbs 115 In-Lbs 13 N-m Connects: Intake Manifold To Cylinder Head Years: All Vote Record: 0/1(0%) Note: 3100 - Lower Bolts - 2 Steps: 5 FtLbs; 9.58 FtLbs Here are the head bolt torques for a 3.8
37 Ft-Lbs 444 In-Lbs 50.17 N-m Connects: Cylinder Head To Engine Block Years: 1999-2005 Vote Record: Vote Note: 3800 II - 2 Steps: 37FtLbs; +120deg
13 Ft-Lbs 156 In-Lbs 17.63 N-m Connects: Exhaust Manifold To Cylinder Head Years: 1999-2005 Vote Record: Vote Note: 3800 II - Exhaust Manifold to Cylinder Head - NOT FRONT 2
7.42 Ft-Lbs 89 In-Lbs 10.06 N-m Connects: Fuel Rail To Intake Manifold Years: All Vote Record: Vote Note: 3800 II - Fuel Rail Mounting Bolts 2.25 Ft-Lbs 27 In-Lbs 3.05 N-m Connects: Idle Air Control Valve To Throttle Body Years: All Vote Record: Vote Note: 3800 II - Idle Air Control Valve to Throttle Body Type: Bolt Dim: Length: Head: Nut Grade: 11 Ft-Lbs 132 In-Lbs 14.92 N-m Connects: Intake Manifold To Cylinder Head Years: All Vote Record: Vote Note: 3800 II - Intake Manifold to Cylinder Head Bolts/Nuts
7.42 Ft-Lbs 89 In-Lbs 10.06 N-m Connects: Intake Manifold Plenum To Intake Manifold Years: All Vote Record: Vote Note: 3800 II - Intake Manifold (Upper) to Lower Manifold Type: Bolt Dim: Length: Head: Hexagon Grade: 14 Ft-Lbs 168 In-Lbs 18.98 N-m Connects: Knock Sensor To Cylinder Head Years: All Vote Record: Vote Note: 3800 II - Knock Sensor

Jul 24, 2016 | 2001 Buick Century

1 Answer

03 Dodge Intrepid intake manifold torque specs top & bottom is for 3.5 V6


Lower Intake:
  1. Use a skin coat of RTV silicone on both sides of the water passage ports (outer most holes) and put the new lower intake gaskets into place
  2. Hand tighten the 13mm head intake bolts and Torque the bolts , starting from the center and working your way out in a circular pattern
  3. Torque these bolts in a few small increments until they have reached 250 inch pounds of torque.
  4. Upper Intake Plenum:
  5. When installing the intake air plenum , be sure to catch the four center bolts and the two side bolts (stiffener brackets) before tightening , The center bolts should be torqued to 250 inch pounds .The fuel rail bolts should be torqued to 100 inch pounds

Jun 24, 2016 | 2003 Dodge Intrepid

1 Answer

Rocker arm torque spec and intake manifold torque spec and pattern


I could not answer this any better than what I have found online. Here is a guy that has posted removal and re-installation in great detail as well as great photos.
LIM and Head Gasket Change Walkthrough FAQ GrandAmGT com Forum

I give all the credit for this answer to the poster.

Sep 12, 2014 | 2002 Pontiac Grand Am

1 Answer

Intake torque on top & bottom bolts


Apply sealer to the lower intake manifold bolts prior to installation. On the 5.0L and 5.7L engines, install the bolts and torque in sequence as follows:
Step 1: 71 inch lbs. (8 Nm).
Step 2: 106 inch lbs. (12 Nm).
Step 3: 11 ft. lbs. (15 Nm).


12_23_2011_2_54_59_am.gif

Fig. Lower intake manifold bolt tightening sequence-5.0L and 5.7L engines / zoom image link here

Upper intake manifold mounting bolts/studs, torque in a crisscross pattern as follows:
  1. Step 1: Torque the bolts/studs to 44 inch lbs. (5 Nm).
  2. Step 2: Torque the bolts/studs to 83 inch lbs. (10 Nm).

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day and Merry X-mas.

Dec 23, 2011 | 1999 Chevrolet Tahoe

2 Answers

2001 daewoo lanos dual overhead 1.6 liter head bolt torque and sequence


  1. Tighten cylinder head bolts to 25 N.m (18 ft. lbs.). Tighten bolts an additional 70 degrees plus 70 degrees plus 30 degrees using angular torque gauge .
2001-daewoo-lanos-dual-overhead-1-6-vrq3bch1e30nz1jlq5sn5nnt-4-0.gif

Oct 20, 2011 | 2000 Daewoo Lanos

1 Answer

Intake manifold torque spec


The Intake Bolt Torque...

Tighten in 3 steps: Step 1: 7.5 FT Lbs Step 2: 15 FT Lbs Step 3: 24 FT Lbs(to torque bolts & nuts, start in center using crisscross pattern)

Hope helps (remember to rate and comment this).

Sep 12, 2010 | 1998 Ford Mustang

1 Answer

How to replace the intake manifold? I have a 96 grand cherokee v8, unable to replace the thermostat housing to the manifold because one of the screw holes cracked off on the manifold.


Position The Intake Manifold Gasket On The Engine.Dowels May Be Provided To Hold The Gasket In Place During Manifold Installation.. The Use Of Silicone Sealer Is Required. Especially Where The Front And The Rear Seals Meet The Side Gaskets On V-type Engines. Installing An Intake Manifold On V-type Engines Can Be Difficult. It Is Critical That You Use Sealer Properly On The Engine To Prevent Vacuum,Coolant, And Oil Leaks.

Start All The Fasteners By Hand Before Tightening. This Will Aid In Bolt Hold Alignment. Then Torque The Intake Manifold Fasteners To Specifications. Use The Specific Torque Pattern Given In The Service Manual.. Basically The Pattern Will Be A Crisscross Pattern

Apr 09, 2010 | 1995 Jeep Grand Cherokee

1 Answer

What is the bolt torque settings for an intake manifold on a 1973 Ford Mustang Mach 1 with a 351C and 2-barrel heads? Also, Where can I find a diagram showing the sequence or pattern for placing the intake...


Intake Manifold 5/16 Bolts Non-Hardening sealers 25 ft-lbs
Cast Iron Heads 3/8 Bolts 30 ft-lbs

The torque sequence is snug all down then just star left rear then right front then right rear then left front and so on

Nov 27, 2009 | Ford Mustang Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...