Question about 2010 Chrysler Sebring

Open Question

Where is the blower resistor located on a 2010 sebring

Where is the blower resistor located and how do I replace

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 36 Answers

SOURCE: 1998 Chrysler Sebring JXI Convertible Blower Motor Not Working

Sounds like it in the switch or the electrical plug at the switch.The electrical plug could be burnt and need repairing or replacing. Need to remove the dash fascia, Careful not to damage clips. If the cover has no visible screws or bolts, then it clips into place. Unbolt heater controls and pull contol forward. Not a fun job but with patience you should be ok.

Posted on Mar 11, 2009

Ad
  • 4 Answers

SOURCE: have to change blower motor resistor where is it located

Located behind glovebox. 2 screws and 2 plugs. very simple

Posted on May 30, 2009

  • 412 Answers

SOURCE: help with location and replacing blower motor resistor

depends on what year van..1996-2000,located in engine compartment just above right strut tower at firewall..2001-2007..located behind glove box

Posted on Jun 12, 2009

wracefans24
  • 1985 Answers

SOURCE: where is the blower resistor, and how do you get

open the glove box,remove the plastic glove box stopper,then remove the glove box,the blower motor resistor is held by two screws .

Posted on Dec 08, 2009

  • 1565 Answers

SOURCE: where is the fan blower

http://www.automotivehelper.com/topic294308.htm

This should be about the same.

Posted on Sep 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the resister located


on the firewall close to the blower motor usually

Feb 29, 2016 | 2010 Ford F-150

1 Answer

Blower Motor Resistor


Follow wires from blower motor back to connection on ducting, that will be your resistor.

Jan 21, 2014 | 2010 Dodge Grand Caravan

1 Answer

2010 Chrysler sebring the heater isn't working. Changed the blower motor resistor and that didn't solve the problem. Took out the blower motor and checked it and it is working. I removed the insturment...


Use the test light and check for power at the resistor- one wire there would be for high speed, which basically bypasses the resistor.
Also check for power at the blower motor with key on and blower switch on high. If you have power and you know the blower motor is good, it could be a ground problem for the blower.

Sep 03, 2017 | Cars & Trucks

1 Answer

1999 Chrysler Sebring convertible - only hi speed option still works - where is resistor and/or blower motor and how to fix


Remove the lower right silencer panel. Remove the electrical connector, it is plugged into the resistor. Then replace the resistor. Since the blower motor works on high speed it is most likely the resistor.

Feb 16, 2011 | 1999 Chrysler Sebring

1 Answer

Switch on a/c only works in the 4th position, not on 1,2 or 3


Sounds like you have a bad blower motor resistor. The resistor is located near the blower motor under the passenger side of the dash. The resistor uses a series of resistors to drop voltage which makes the blower run at different speeds. High speed bypasses the resistors and allows full voltage to the blower motor.

For more info click the link below
http://www.fixya.com/cars/r6571076-blower_motor_not_work

Feb 08, 2011 | 2003 Chrysler Sebring

1 Answer

I have a sebring 2004 and I need to change the blower fan resistor. What is the easiest way to get to the resistor? Some tell me I have to remove the whole front dash.... thanks Ginette


You shouldn't have to remove the dash for this vehicle, move the seat all the way back, remove the covers under the passenger side dash, the blower motor and resistor should be located there.

Jan 08, 2011 | 2004 Chrysler Sebring

1 Answer

Need to know how to replace Blower motor and resistor for 1999 Chrysler Sebring.


Go to this link for detailed info on replacing blower motor resistor for '02 Sebring ... part looks different for the '99, but instructions are the same.
http://www.automotivehelper.com/topic294308.htm

Sep 09, 2010 | 1999 Chrysler Sebring

1 Answer

Where is the blower resistor located on the 2001 sebring


blower motor resistor is behind glove box.you have to remove it to get to it.besure you disable airbags.thats a safety precaution.

Jun 13, 2009 | 2001 Chrysler Sebring

Not finding what you are looking for?
2010 Chrysler Sebring Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...