Question about Volkswagen Cars & Trucks

Open Question

Vw transporter only reverse gear works, no forwards gears

My vw transporter 2004 T28 has only reverse gear and no forward gears

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
dr_greg
  • 192 Answers

SOURCE: cannot shift into reverse although forward gears all functional

have ur shift linkage bushings replaced....most likely thse are torn or completely broken .. this is common on these models..also on some vw's of the same years

Posted on Apr 10, 2009

Ad
  • 1 Answer

SOURCE: My manual trans in a 1999 vw beetle reverse drive forward

I had a simular sounding experience with my 99 beetle after hitting a curb. felt like it was stuck in 3rd and 4th only-had no reverse. My problem was that there was a linkage on the sifter gears broken.

Posted on Jun 24, 2009

kirkx
  • 2019 Answers

SOURCE: 1999 F250 only goes in reverse, no forward gears.

I believe that reverse is operated by a brake band. So it seems to be stuck. It is operated by a piston, and the seal could have swelled and caused too much friction. But you could loosen up the adjustor so that it is disengaged, in order to get forward gears again. Perhaps you can force the piston to retract as well, once you drop the pan again.

Posted on Jun 26, 2009

  • 45 Answers

SOURCE: i have a 97 VW Golf auto trans, I have no reverse

Check your fluid level to make sure its up to the specified level, then I'd be checking out your linkage from your shifter inside the car right to the transmission, it sounds like to me your linkage may be worn enough to put the vehicle in drive but not reverse. The linkage bushings are a common problem on vdubs. See if you can put the car in reverse by moving the linkage arm directly attached to the transmission (make sure you have someone in the car with the brakes on or caulk the wheels) if it does go into reverse when you manually move the direct linkage arm at the transmission then replace your linkage bushings, if not then the only other problem would be a transmission internal problem. Good luck

vdubs 4-ever

Posted on Aug 01, 2009

pappapumpdaf
  • 635 Answers

SOURCE: turbo 350 trans no forward gears but does have reverse

It's either your servo, or your bands.
Either way, the tranny needs a good cheap shop repair.
I'd just get a warrantied salvage yard tranny if I were you and save a few hundred bucks.

Posted on Mar 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vs auto have forward gears even in reverse any ideas please


A4LD stuck in forward, even while in neutral and reverse. - Ford ...

https://www.explorerforum.com/forums/showthread.php?t=216567

May 27, 2008 - 19 posts - ‎5 authors
I did find a thread that referred to an "always in a forward gear" A4LD problem, ... Eventhough band adjustment should not have anything to do with the .... in the transmission and then it auto shifts through the gears normally.

700r4 forward in all gears, even neutral, no reverse - Third ...

www.thirdgen.org/forums/.../631383-700r4-forward-all-gears.html
Oct 21, 2011 - 700r4 forward in all gears, even neutral, no reverse ... It has no reversebut when I put it in reverse it tries to pull the motor down like the rearend ...

my car is not moving forward or backwards even with gea


Dec 27, 2015 | Cars & Trucks

1 Answer

1999 vw jetta 5-speed. went off the road and got stuck in a ditch. reverse would not work so i had it towed. car drives fine in forward gears but now reverse won't work. if clutch is held in certain...


At a guess the "off" bent something in the linkage or change cables. I suspect that selecting Reverse place the gears in partial mesh (not synchromech like the fwd gears) , and the "pop" is the gears falling out of mesh. Check that the engine mounts are not damaged.

Mar 02, 2018 | Volkswagen Jetta Cars & Trucks

1 Answer

2003 cadillac cts 3.6L ..no reverse..got all forward gears also goes forward in neutral


The transmission has a bad solenoid in it for the reverse gear.

Jan 02, 2011 | 2004 Cadillac CTS

2 Answers

98 vw beetle wont go in reverse


I have a 1998 and I just confronted the same problem. It seems to take like 1 gear in reserve and like 2 gear in 1 gear. Any thoughts? I don't really it should be the transmission since it still works going forward in 2 different gears. Thanks.

May 13, 2010 | 1998 Volkswagen Beetle

1 Answer

I have a 2000 Expedition 4.6L Triton. I've had truck about 7 years and love it. I have had all the transmission issues this truck can have...(I thought) until now this: SYMPTOM Transmission drives well in...


4R100 or 4R70W?

Geartrain
Power is transmitted from the torque converter to the geartrain components through the input shaft and forward clutch cylinder.
  • By holding or driving certain members of the gearset, four forward ratios and one reverse ratio are obtained and transmitted to the output shaft. The ratios are as follows:


GEAR RATIO 1ST 2.71 to 1 2ND 1.54 to 1 3RD 1.00 to 1 4TH 0.71 to 1 REVERSE 2.18 to 1
Input Shaft
The input shaft is supported by two bushings in the stator support. End positioning of the input shaft is controlled by the splines in the converter turbine and the overdrive planet assembly.
Output Shaft
The output shaft is supported by two bushings in the case and by the slip-yoke and bushing in the extension housing. End positioning is controlled by the parking pawl gear and snap ring or shoulder and by the reverse ring gear hub and snap ring.
Overdrive System
The overdrive planetary system consists of the overdrive planet assembly, overdrive sun gear, overdrive ring gear, coast clutch cylinder, overdrive one-way clutch assembly and the center shaft, as shown in the following illustration. The overdrive planet assembly is splined to the input shaft. The overdrive sun gear is centered by a bushing on the input shaft and held in place laterally by needle bearings on the reactor support and the overdrive planet assembly. The overdrive sun gear is splined to the coast clutch cylinder, which in turn is splined to the overdrive one-way clutch inner race.
The outer race of the one-way clutch is splined to the overdrive ring gear, which is splined to the center shaft. The center shaft is centered by the forward planetary assembly and is laterally held by needle bearings on the center support and the overdrive planet assembly. The center shaft is splined into the forward clutch cylinder.
Two friction clutches are assembled in the overdrive planet assembly. The coast clutch is splined between the coast clutch cylinder and the overdrive ring gear. The coast clutch is activated to perform engine braking in MANUAL 1, MANUAL 2 and third gear with the transmission control switch engaged.
The overdrive clutch is splined between the case and the coast clutch cylinder. The overdrive clutch holds the coast clutch cylinder and, in turn, the overdrive sun gear, to permit the planet assembly to overdrive the ring gear.
--------------------------------------------------------------------------------------------
Forward Drive System
The forward drive system consists of the forward clutch cylinder, intermediate brake drum, intermediate one-way clutch, input shell, forward ring gear, forward ring gear hub, forward/reverse sun gear and the forward planetary carrier and forward planetary gears.
The forward clutch cylinder is splined on the center shaft. The forward ring gear is piloted on the forward ring gear hub. Thrust bearings on the forward planet assembly and forward clutch cylinder hold the forward ring gear hub in place.
The intermediate brake drum is radially supported by bushings on the center support and is laterally controlled by thrust washers on the forward clutch cylinder and center support. The intermediate brake drum has the inner race of the intermediate one-way clutch press-fitted on its pilot. The intermediate one-way clutch's outer race is splined to the intermediate friction clutch, which is splined to the case. The intermediate brake drum has lugs that are slotted into the input shell to form a mechanical connection. The input shell is splined into the forward/reverse sun gear. The forward/reverse sun gear is common to two planetary gearsets. The forward planet is splined to the output shaft and is laterally positioned by needle bearings on the sun gear and on the forward clutch cylinder, as shown in the following illustration.
Two friction clutch assemblies, the direct clutch and the forward clutch, are shown with the forward planetary assembly. The direct clutch assembly splines the forward clutch cylinder to the intermediate brake drum. The forward clutch assembly splines the forward clutch cylinder to the forward ring gear. The forward clutch is activated during all forward gears. While in third or fourth gear, both the direct and forward clutches are applied to hold the forward planetary assembly and enable it to act as a solid shaft.
In second gear, the intermediate clutch assembly holds the forward/reverse sun gears. It is applied, along with the intermediate one-way clutch, to hold the intermediate brake drum, input shell and forward/reverse sun gear. In higher gears, the one-way clutch overruns.
----------------------------------
Low and Reverse Drive System
The reverse planetary assembly consists of the reverse planetary carrier, reverse planet gears, the reverse ring gear, the reverse ring gear hub, the reverse clutch hub and the low-reverse one-way clutch assembly.
The reverse ring gear hub is splined to the output shaft and to the reverse ring gear. The reverse ring gear hub is laterally held by a needle bearing on the inner race of the low-reverse one-way clutch and a snap ring on the output shaft. The reverse planet assembly is splined to the low-reverse clutch hub. The low-reverse clutch hub is connected by the reverse clutch to the case. The inner race of the one-way clutch is bolted to the case.
The reverse clutch assembly is activated in REVERSE gear and in MANUAL 1. The reverse clutch bypasses the reverse one-way clutch during coast and MANUAL 1. The reverse clutch holds the reverse planet assembly in REVERSE gear to enable the sun gear to drive the reverse ring gear in the opposite direction.
-------------
Apply Components
The following information describes the operation of the three 4R100 one-way clutches.
One-Way Clutch—Overdrive
The overdrive one-way clutch, shown in the following illustration, transmits engine torque from the overdrive sun gear to the overdrive ring gear in first, second and third gear range. The overdrive one-way clutch transmits power when the sprags are engaged between the inner and outer races. The inner race is splined to the coast clutch cylinder, which in turn is splined to the overdrive sun gear. The outer race is splined to the overdrive ring gear.
The overdrive one-way clutch engages whenever the overdrive planetary system attempts to drive the overdrive sun gear clockwise when the overdrive ring gear has a counterclockwise torque from the vehicle. When torqued counterclockwise, the overdrive one-way clutch engages and acts as a wedge to lock the sun gear and the ring gear together. During coast, the overdrive one-way clutch enables the ring gear to overrun or spin at a faster rate than the sun gear.
The overdrive one-way clutch overruns when in overdrive (fourth gear). In overdrive, the coast clutch cylinder is held by the overdrive one-way clutch, which in turn holds the overdrive sun gear. This causes the overdrive planet assembly to walk around the sun gear and overdrive the overdrive ring gear. The inner race of the overdrive one-way clutch is thus held stationary while the outer race is allowed to overrun clockwise.
--------------------------------------------

Nov 10, 2009 | 2000 Ford Expedition

1 Answer

1990 VW cabrio wont reverse. Seems in gear but only goes forward


left and push the shifter into the floor like stabbing down ten it will go left a little more and push forward and you will be on your way in good ol R

Jul 25, 2009 | 1990 Volkswagen Cabriolet

1 Answer

My 2004 ford ranger xlt 4x4 won't go into any forward gears, only reverse. When it does go in reverse the engagement is hard?


Sounds like the forward clutches and/or low-reverse one-way clutch. Either way it sounds like it's time for an overhaul

Jul 08, 2009 | 2004 Ford Ranger

1 Answer

Cannot shift into reverse although forward gears all functional


have ur shift linkage bushings replaced....most likely thse are torn or completely broken .. this is common on these models..also on some vw's of the same years

Apr 09, 2009 | 1990 Porsche 911 Carrera

1 Answer

My manual trans in a 1999 vw beetle reverse drive forward


I had a simular sounding experience with my 99 beetle after hitting a curb. felt like it was stuck in 3rd and 4th only-had no reverse. My problem was that there was a linkage on the sifter gears broken.

Apr 01, 2009 | 1999 Volkswagen Beetle

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

78267 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...