Question about 2002 Honda CR-V

Open Question

Location of knock sensor on 2002 honda crv - 2002 Honda CR-V

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 109 Answers

SOURCE: Location of the PCV valave in the 2002 Honda CRV

pcv valve should be located on the valve cover..but some new vehicles don't have one it is built into the valve cover itself..

Posted on Dec 02, 2008

Ad
  • 2 Answers

SOURCE: 2003 Honda Oddyssey - PO325 Knock Sensor

If The engine in your van is a 3.5L, the knock sensor is under the upper intake manifold. This has to be removed in order to access the sensor on top of the engine block. The job requires an upper intake gasket set and about 1.5 hours to do; if you are handy with tools. For those who aren't; better off leaving this one to the professionals.

Posted on Dec 09, 2008

  • 1 Answer

SOURCE: central locking unit 1997 Honda CRV

Hi the central lock unit is located in the drivers door

Posted on Apr 06, 2009

keemo68
  • 1263 Answers

SOURCE: 2002 HONDA CRV COLD ANTIFREEZE LEAK

this happens alot on older vehicles most often times because the coolant hose shrink and expand around a fitting. try and tighten all coolant clamps. this often is all it takes to solve the problem. you should also look to see that all seals around heads of engine show no seepage

Posted on Apr 25, 2009

  • 58 Answers

SOURCE: 2002 honda crv air filter change

Hi!

Can you specify if you are referring to the engine intake air filter or the cabin air filter?
If you are referencing the cabin air filter, the attached youtube video should help.

I originally created the video for the Odyssey, but found out after looking at my dad's CRV that it is essentially the same procedure as the Odyssey, and have also noticed that the same stands true for most Honda vehicles built between 2005 and 2009.

Happy motoring!

Posted on Jun 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the radiator fan switch on a 2002 Honda CR-V located?


this should help, it locates most of the components related to the cooling fan with the switch included
f5b7279d-accb-47df-ba97-f1c4fc57e744.gif

Aug 21, 2014 | 2002 Honda CR-V

1 Answer

05 Honda crv knock sensor, is it hard to replace?


http://www.k20a.org/upload/k20aorgspecmotor/build/thumbnails/tn_Picture%20993.jpg
right by the stater under the intake manfold, google: k20a3 knock sensor location

Feb 11, 2013 | 2003 Honda Odyssey

1 Answer

Where is the knock sensor located on a 2003 honda crv engine


Just done this on a 2002 (mk2) CR-V with 2 litre ivtec petrol engine. The knock sensor is screwed into the engine block underneath the inlet manifold. The best access to it is by removing the inlet manifold but this takes time. I replaced it from below by:

1) remove the undertray that is fastened to the front bumper, to do this its two bolts and lots of plastic rivets - lever the centre pins out of the rivets and they will come out.
2) from underneath the car you can now see the knock sensor in the centre of the engine block, it has a 27mm AF hex and a cable going to it.
3) disconnect the cable from the knock sensor, it has a latch on the plug that needs to be pressed, if like me you can't reach to press the latch don't worry move on to the next step.
4) Get a large 27mm open end spanner and undo the knock sensor, if you wern't able to disconnect the cable in the previous step it is possible to take the sensor all the way out of the block with the cable still attached. It is then much easier to unlatch the cable.
5) to refit the new one you need small hands or better access - there is a plastic clip holding a cable to the engine on the left hand side of the engine I found that by removing this clip (a single 10mm bolt) I could move the bundle of cables and get better access to refit and connect the new knock sensor.
6) Fit the new knock sensor into the block, tighten it to the recommended torque (can't get a torque wrench in so just nip it up, do not overtighten).
7)reconnect the cable.
8) refasten the cable clip holding the bundle of cables you removed to get access.
9) refit undertray.
10) I don't have a code reset device and the check engine light was still on after this work but it went out after three complete engine cold,hot,cold cycles. and has stayed out since.

Mar 24, 2012 | 2003 Honda CR-V

1 Answer

I have a honda 2002 crv, i got this the malfunction light on, and was diagnosed to be P1166 - air fuel ratio sensor (sensor 1) heater circuit malfunction P1167 - air fuel ratio sensor (sensor 1) heater...


in the fuse box, it may be marked, or in your owners manual. Chefk them all, then you will know if any fuses are bad. Usually its the sensor if the fuses are good.

Aug 26, 2011 | 2002 Honda CR-V

3 Answers

Where is the fuel filter located honda crv 2002


normally for honda it should be located to the firewall close to the battery...

Jun 12, 2010 | 2002 Honda CR-V

1 Answer

CRV has knocking sound coming from rear passenger side


inspect the braking system for warped or uneven rotor surface, as this may cause this noise and uneven pad wear. CV joints also could cause this if the boots are torn, have insufficient grease, are damaged,or have worn bearings. Hopefully this helps

Jul 22, 2009 | 2002 Honda CR-V

2 Answers

WHERE DOES THE KNOCK SENSOR, AND OXYGEN SENSOR GO?


The knock sensor is located on the side of the engine block. And the oxygen sensors are located in the exhaust system. There will be one oxygen sensor (upstream) screwed into either the exhaust manifold or the exhaust pipe before the catalytic converter. The other oxygen sensor (down stream) will be screwed into the exhaust pipe just after the catalytic converter.

May 12, 2009 | 1999 Isuzu Rodeo

2 Answers

Code 1167 - Honda CRV 2002


Check all fuses, then check the wiring of the two 02 sensors on either side of the cat. converter. If the fuses and wiring are fine, it is likely one of the oxygen sensors; one is about $50 and the other is $200 (parts only). Use only Honda recommended parts, not BOSCH. 

Jul 22, 2008 | 2002 Honda CR-V

Not finding what you are looking for?
2002 Honda CR-V Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...