Question about 2002 Honda Odyssey
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
open the rear hatch. Between the tail light housing and the rear hatch opening there is a trim strip with two flush fitted flap doors. Insert a small straight blade screwdriver into the small slot on the tail light side of the flap. Pry gently inboard and the small flap will open (the hinge side of the flap is on the side of the rear hatch opening.) Now you can remove the screws that hold the tail lamp assembly in place. Finally, there is still a "spear point" clip that fits into a socket near the front outboard corner of the assembly. Gently pry with a tape wrapped screwdriver (avoids scratches) and force the assembly straight back. The clip should release and free the assembly so you can change the bulb(s).
Posted on Jan 24, 2009
open the rear hatch. Next to the brake light assembly, between it and the hatch there are two flap doors in the brake light trim. Take a small flat blade screwdriver and open these doors. The hinge side of the flap is nearest the hatch opening. when opened, the flaps will reveal two screws. Remove these. then wrap a flat blade screwdriver with some tape (protects the paint) and put the blade at the front outside corner of the brake light assembly. Pry gently rearward and a plastic spear point clip will release. With the assembly off, you can see how to twist out the bulb sockets and replace the bulbs. to replace, put the spear point clip in first, replace the screws, and close the flaps in the trim.
Posted on Mar 05, 2009
you need a haynes repair manual . it save you time. it shows you step by step . what to remove to get to timing belt or chain . show you photos how to set timing chain cam and crank timing marks.
Posted on Apr 04, 2009
Try looking here for general removal/replacement info... http://autorepair.about.com/library/a/1i/bl830i.htm
Posted on Jul 02, 2009
the procedure is as follows:--
You have to do it from underneath the vehicle. Take off the rivets to the two plastic covers, and then you will be able to see the tensioner for the belt. Use a 3/4 inch wrench on the tensioner (don't put it on the bolt that holds the tensioner on), and pull it toward the vehicle. The belt will loosen, and you can take it off.
As a car owner, you know how important the belt tensioner is for your 2002 Honda Odyssey. However, internal parts wear and damage will loosen or seize the tensioner wheel, causing the belt to slip and make noise. Eventually, the belt may break, shut down the engine and lead you into a serious traffic accident. Before that happens, replace the tensioner on your Honda model and save yourself a lot of problems:----
Remove the Drive Belt:--
1)Look for the drive belt routing diagram on your vehicle's engine compartment. This is a black and white label, about 4 by 6 inches, usually attached to the radiator shroud or near the strut towers inside the engine compartment. This diagram will be your guide when reinstalling the drive belt. If cannot find one, make a simple sketch on a piece of paper.
2) Insert a belt-tension release tool, or similar tool, into the auto-tensioner arm.
3)Rotate the auto-tensioner arm counterclockwise and slip the belt off the tensioner pulley.
4) Release the auto-tensioner but do not let it snap back in place.
5) Remove the drive belt from the engine compartment.
Replace the Belt Tensioner
1) Unscrew the two auto-tensioner mounting bolts using a ratchet, ratchet extension and socket. Note the location of each bolt because they are of different size.
2) Remove the old auto-tensioner from the engine compartment.
3) Set the new auto-tensioner in place and start the two mounting bolts by hand. Make sure you install the bolts in their original place.
4) Start tightening the bolts until they hit the stop using the ratchet, ratchet extension and socket.
5) Torque the two bolts using a torque wrench. Torque the small bolt to 16-foot pounds [22 Nm] and the large bolt to 47-foot pounds [64 Nm].
will help. Thanks please keep updated.please do rate
the solution positively .thank you for using fixya
Posted on Mar 01, 2010
Tips for a great answer:
Jan 13, 2013 | 2002 Honda Odyssey
Jun 21, 2012 | 2002 Honda Odyssey
Jan 31, 2010 | Honda Odyssey Cars & Trucks
Sep 19, 2009 | 2002 Honda Odyssey
Jul 02, 2009 | 2005 Honda Odyssey
Jun 21, 2009 | 2001 Honda Odyssey
Mar 22, 2009 | 2002 Honda Odyssey
Jan 24, 2009 | 2002 Honda Odyssey
Feb 07, 2017 | 2002 Honda Odyssey
149 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: