Question about 1998 Mazda Millenia

1 Answer

98 mazda mallinia no heat controller seems to be working i can turn knob and it will go from 90 to 65 degrees but wil not turn air to hot just stays cold

Also should you be able to adjust the ambiant also ?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 88 Answers

Heater theromstat is faulty, it is located near the heater core in most vehicles, It monitors the temperature of the core or in some vehicles the inside cabin temperature and open or closes allowing heated water to flow through your heater core. Look on your heater hoses and you will find it. Most of the time its a DIY job and not that expensive but don't bet on it being cheap, they are proud of some of those things. Just have to check with your local parts house and find out. Used to be a common problem but I guess technology has caught up with them. Hope this helps.
Gillight

Posted on Oct 27, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Murphybanton
  • 2004 Answers

SOURCE: water leak inside car

Try check the AC water outlet hose there must be a leak from there.

Posted on Apr 30, 2009

  • 1986 Answers

SOURCE: Can't find the adjustment knob for the headlights on a 2008 Mazda

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 30, 2009

  • 1 Answer

SOURCE: 2004 Mazda RX8 Heater problem

There is a well known problem that is a manufacturer's defect with the soldered connection on the circuit board behind the temperature knob. There is a fix to re-solder the connections but the dealer will gladly take $450 to replace it with the same bad board that will last you a while. Look for the link to show you how to fix it yourself.

Posted on Dec 19, 2009

wracefans24
  • 1985 Answers

SOURCE: heat not blowing hot in 2003 mazda mpv (tepid

you need to try replacing the thermostat first to make sure the engine water gets up to 195 degrees.

Posted on Dec 29, 2009

  • 369 Answers

SOURCE: My heater wont work on my mazda, the temperature knob broken?

try replacing your thermostat

Posted on Jan 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 sonoma air temperature stays hot when i turn the control knob. A/C works fine,but the air does'nt get cooler when I turn the knob


Easiest place to start is checking for a broken control knob. Pull the knob off and see if it is cracked/broken on the back side. You can turn the metal control rod then by hand to see if it works. If no problem found there, you will have to check for a blend door motor/actuator that controls heat/cooling attached to the heater box under the dash for proper operation

Jan 06, 2016 | 2002 GMC Sonoma Extended Cab

1 Answer

2003 dodge ram 4.7 heat/air trouble


if you have a tilt wheel,you may have a broken wire,replace the whole colunmb also,,,,,,,,,,,,,(pics)look for 2 and 7 ,,blend door actuators,,
25683800-dbg1d4nweydockjpekf2wtox-1-0.png

25683800-dbg1d4nweydockjpekf2wtox-1-2.gif

25683800-dbg1d4nweydockjpekf2wtox-1-5.gif

25683800-dbg1d4nweydockjpekf2wtox-1-9.gif

May 07, 2015 | 2003 Dodge Ram Pickup 1500

1 Answer

No heat / heater not working


not blowing air or when switch is on blows cold air when you have climate control knob turned over to heat? it could be a switch or blower motor or fuse if its not blowing any air. if its blows cold air when knob is on heat then is can be thermostat or low on coolant or it could be climate control module or it could be a air filter in dash.

Apr 05, 2013 | 1993 Mazda Protege

1 Answer

No heat in my 98 expedition ,fan works,blend door works,but blows cool air


Make sure coolant (Water Is full)
The system is clog. Or Heater valve is not open when you slide the control knob to hot or cold.
-Check the heater valve by moving the control knob to hot and cold. The valve turns or not. If it turns then the system is clog. If not turn at all then the valve is not function. (the cable might be slip off/Hook or connect it back to the valve)
*If it turn then the system is clog.>>>Need to flush.
-Disconnect the heater hoses from engine (Both hoses) and flush it with garden water hose from both direction for couple minute.
Reconnect, fill or add more water to radiator to full then run.
You should be good to go.

Mai Lor

Feb 25, 2013 | Ford Expedition Cars & Trucks

2 Answers

2005 RX8 heater is blowing cold air. Fluids are topped up.


You need to repair the heater core with a soldering gun.

If you do not have heat, or only have heat, IMHO it is most likey the AC/heater control unit. This is the part which has the AC/heat control buttons and knobs.

Easy Diagnosis:
The easiest way to verify this is to turn on the radio, press and hold the power on/off button and press and hold the scan-up button for a second (full second). The word "A/C TEMP" should appear on the left of the display and a number from 0 to 16 on the right. I suspect yours will have the number 0 (or 16 if heating only problem) displayed no matter where you turn the temperature control knob. If this is the case you could turn the temp. knob to full heat and see if it goes to 16 after pushing down or to the right on the knob.
In a working system, the number moves evenly in increments of 1, from 0 to 16 as you turn the temperature knob.

Easy Fix:
I was able to take mine out and solder 3 loose connections to fix it.

The beginning steps are the same as for any radio removal procedure and check for loose connections.

Dec 14, 2009 | 2005 Mazda RX-8

2 Answers

1995 Chevy k1500 heater problems.


For a 95 Chevy Silverado....I replaced the Blend Door Actuator on the passenger side. Just behind the slide out cup holder. Yo ucan acces easily by removing the ash tray piece and the glove box....Or just the glove box and work like hell to get a socket in a tight place.

There are 2 actuators....one controlling the (Mode and Temp 89018681) and the other the (Air Inlet 89018367). I called the dealer and the parts were 85-125. I got it From TBA Auto (local store) for 39.00. A 20 min job at most.

May 27, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

98 Ford Experdition V8-281 4.6L SOHC-the heat will not get hot.


Have you tried replacing the heater core ? If the flushing of the heater core did not work, the heater core may be bad. Very clogged with gunk and residue. did you try to check the valve that opens the hoses to the heater core. This valve can be vacuum, opened by cable or electric. Check to see if the hoses get hot at the firewall. they should be hot.

Feb 07, 2009 | 1999 Ford Expedition

2 Answers

I have a 98 ford experdition and the heat will not get hot.


I would say that it is probably the water pump. I have run into 3 of these on these models this year. They do not overheat however when hooking flow meter up to measure the coolant flow they barely move the meter. Pulled the pump of and found the fins either loose from the pump or the fins worn out.

Feb 07, 2009 | 1999 Ford Expedition

1 Answer

Cold Am . I turned the left knob 45 degree . All i get is HEAT,knob moves


Hi rafis1234,
if you are handy, you can remove the small dash panel where the a/c control knobs are and then you'll access the lever mechanism and most of the time you'll find a rusty lever or someting has jammed the lever.
Cheers

Oct 28, 2008 | 2004 Nissan Sentra

Not finding what you are looking for?
1998 Mazda Millenia Logo

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...