Question about Toyota Cars & Trucks

Open Question

How do i change prado inner cv boot - Toyota Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: drive axle and cv joint

the shaft and the ball cage are already off. the inner piece that goes into the gearbox is not coming out. the boot was changed and I now need to reassemble the parts.

Posted on Aug 30, 2008

  • 740 Answers

SOURCE: HOW DO I REPLACE THE INNER CV JOINT BOOT ON A 2001 BUICK CENTUR

I would recommend that you replace the complete axles instead of just the boots. The boots may be busted/worn and when the get torn/busted they allow sand/dirt inside the CV joint and the bearing inside the CV joint become worn, it all depends on how long the boot has been ripped, its easier and a lot less messy to R/I new axle. For the wheel bearings they need to be pressed in by a hydraulic press. As far as the procedure goes you have to elevate the two front wheels and secure by a lift of jack stands, then take off tires and take off brakes/caliper and caliper chair along with the rotors. You have to remove center nut on axles and remove lower ball joint from knuckle assemble/ hub. Then remove bolts holding knuckle/hub to the struts. Pull knuckle from axles and the hub is out. If you don't have a press and the proper tool you can take the two hubs and the bearings to a machine shop and they will press out and pressing new bearing for you. As for the axles they both can then be pulled/pryed out of the transmission at this time and be fixed or replaced. caution look out for leaking transmission fluid when you pull axles out. The axles are only held by licking rings and can be easily pulled or pryed out. Have something ready to catch fluid. Replace axles in the reverse of taking out. use a piece of wood on the end of axle if there is need to tap it back in with a hammer, listen for a click or snap when its goes back in to transmission. Good Luck

Posted on Dec 12, 2008

michigan man
  • 3533 Answers

SOURCE: toyota prado how to change boot ruber on cv joint.

try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Posted on Mar 21, 2009

468 Chevelle
  • 81 Answers

SOURCE: trying to get the bearing off of the cv axle 1994 camry

I think you mean cv joint. If so, a new axle cost $59. You are doing alot of extra work and the joints could be damaged. The outer joint comes off, but it takes a large hammer. The inner joint usually has an inboard ring clip that you pop out with a screwdriver.

Posted on Mar 27, 2009

  • 416 Answers

SOURCE: when replacing a outer C.V joint boot , do you

you can replace just the outter but you may want to replace the whole axle alot easier

Posted on Jan 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace rubber cv boot on 1999 Isuzu rodeo


how to , who can, what are all steps. are there special tools?
sure. if the boot is bad, so be the joint, Yah think?
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Halfshaft from the vehicle
    • Snapring and bearing
    • Snapring and oil seal
    • Mounting bracket
    • CV-joint boot
    • Circlip and inner joint housing
    • Snapring and spacer
    • Inner joint balls
    • Snapring and inner CV-joint
    • To install:
    • Install or connect the following:
      • Inner CV-joint and snapring
      • Inner joint balls
      • Spacer and snapring
      • Inner joint housing and circlip. Add 150 grams CV-joint grease.
      • CV-joint boot
      • Mounting bracket
      • Oil seal and snapring
      • Bearing and snapring
    • Install the halfshaft and mounting bracket to the vehicle.
    • Check the wheel alignment and adjust as necessary.

Jun 30, 2014 | 1999 Isuzu Rodeo

2 Answers

How to change cv joints


I would replace the complete axle assembly,
it would be cheaper and come with a warranty.

Instructions
  1. Remove the CV Joint
    • Remove the boot straps from the CV joint using a standard screwdriver or a pair of diagonal cutting pliers.
    • Slide the boot back over the interconnecting shaft.
    • Get Chevrolet Info at InsideLine Free News, Videos, Photos & More!
      Detach the stop ring at the base of the CV joint assembly using a pair of snap ring pliers.

    • Pull the CV joint assembly from the interconnecting shaft to force the snap ring at the top of the shaft through the CV joint assembly.
    • Tilt the inner cage (the cage holding the balls in place inside the housing) in different angles to remove the six balls. Use your thumb or a hammer and a wooden dowel, if necessary.
    • Tilt the inner cage enough to remove it from its housing.
    • Rotate the race inside the cage--the part that holds the balls against the inner cage--and remove the race from the cage.
      Replace the CV Joint
      • Apply a thick coat of grease to the new CV joint race using special high temperature/high pressure grease (see Tips below).
      • Install the race inside the new cage. Then install the cage/race assembly inside the CV joint housing.
      • Tilt the cage at different angles and fit the new balls in place.
      • Slide a new CV joint rubber boot over the interconnecting shaft.
      • Install a new snap and stop ring on the interconnecting shaft.
      • Push the interconnecting shaft through the CV joint assembly to force the snap ring through the assembly.
      • Apply a thick coat of CV joint grease to all moving parts of the assembly.
      • Apply a coat of CV joint grease to the inside of the rubber boot. Then slide the boot over the CV joint assembly.
      • Install the boot straps at each end of the boot, and tighten the straps using a clamp tool or screwdriver, depending on the type of clamp.


Mar 22, 2012 | 1997 Chevrolet Cavalier

1 Answer

Im trying to replace the driver side cv. the inner boot came off with the whole drive axcel, except for the inner spine. it looks lkike the previous owner removed the inner cv joint and replaced the boot...


YOU HAVE TO REMOVE WHOLE AXLE AN INSTALL AXLE IN INNER CV JIONT THEN MAKE SURE IT CLIPS IN,INSTALL BOOT AN RECLAMP CV BOOT WITH SPECIALLTY PLIERS

Dec 21, 2010 | Mazda 323 Cars & Trucks

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

3 Answers

When replacing a outer C.V joint boot , do you


you can replace just the outter but you may want to replace the whole axle alot easier

Jan 17, 2010 | 1993 Ford Festiva

1 Answer

Toyota prado how to change boot ruber on cv joint. can you send me some kind of an instruction manual etc. something that can help me replace my boot rubber.


try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 19, 2009 | Toyota Land Cruiser Cars & Trucks

2 Answers

Inner cv joints


inner cv joints are the joints on the inner half of the axle shaftswhere they go into the transmission. sometimes the easiest thing to do is replace the axle shafts

Jan 05, 2009 | 1996 Chrysler LHS

2 Answers

Drive axle and cv joint


Have you already removed the axle from the car?

Aug 30, 2008 | 1990 Subaru Legacy

1 Answer

Front Axel


you have to undo inner cv boot and remove clip inside cv then pull out outer cv with shaft and inner bearing of inner cv,leaving inner cv outer section in diff.If you want to get out inner cv end, diff assembly must come out of vehicle then unbolt plate retainer on diff tube.

Jul 06, 2008 | 1999 Isuzu VehiCROSS

1 Answer

Inner cv boot


go to the advanced auto parts store and purchase the Haynes manual for the car and it will tell you how to change everything on there.

Jun 25, 2008 | 2002 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...