Question about Nissan Xterra

Open Question

Steering wheel removal 2006 nissan xterra

Multi function switch replacement removing steering wheel

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tommyboinow
  • 324 Answers

SOURCE: Steering wheel removal

first you want to unplug the air bag. you do this buy removing the plastic surround around the steering column, where the ignition is, just below the steering wheel itself, then you have to remove the air bag by removing the bolts from the back of the steering wheel...

then get a steeering wheel removal kit, autozone has a loan a tool program.

put the steering wheel tool on and turn oit with a wrench adn the wheel will pop off...

Posted on Nov 26, 2008

  • 1 Answer

SOURCE: steering wheel removal

were airbag module for passenger

Posted on May 15, 2009

wireguy212
  • 1627 Answers

SOURCE: when replacing multi-function switch on a 2004

Yes the stearing wheel must come off.

Posted on Nov 11, 2009

  • 271 Answers

SOURCE: Need to remove the steering wheel so i can replace

Disconnect the battery negative/earth/.Wait for at list 10 minutes to deactivate SRS airbags.Then remove the drivers airbag useing 5 mm allan key behing the steering wheel.There is two holes.Disconnect carefully the airbag.24mm socket to unscrew the steering wheel.Pull out the steering wheel.Disconnect the plugs of the switches.There is 3 screws/flat screwdriver/ Thats all

Posted on Jun 27, 2010

  • 3911 Answers

SOURCE: I need to replace the multi-function wiper switch

the switch is underneath the steering wheel. the steering wheel needs to be pulled to replace the switch. the airbag is in the steering wheel, and a trained tech with a puller is needed to pull that wheel off without screwing up the airbag.

Posted on Oct 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace dimmer switch on 1999olds 88


Remove airbag fuse. Disconnect battery. Remove two/4 screws (usually Torx-forget the size but rather large maybe T7) from the back side of the steering wheel. Remove airbag assemble . Carefully disconnect the harnesses. Remove the large steering wheel retaining nut. Using a steering wheel puller remove the steering wheel. At this point you may need to remove the shroud from the steering column. Usually t 10 or T15 screws. Remove retaining screws from the multi function switch. Carefully un plug and remove. Installation is reverse. Highly recommend a haynes or Chilton repair manual for this job. Steering wheel puller can be rented from most auto parts chain stores.

Jul 14, 2016 | Oldsmobile 88 Cars & Trucks

1 Answer

Steering column top bearing replacment


double posted, with 1999 added.
the FSM says dont reuse steering wheel bolts.. (unique)
here is an online quote to get to the combo switch
quote;
Removal & Installation
  1. Disconnect and isolate the battery negative cable. WARNING(bags can kill, my comment)
    Wait two minutes for the airbag system reserve capacitor to discharge before performing further diagnosis or service.
  2. From below the steering column, remove the three screws that secure the lower steering column shroud to the multi-function switch mounting housing.
  3. Using hand pressure, push gently inward on both sides of the upper shroud near the parting line between the upper and lower shrouds to release the snap features that secure the two shroud halves together.
  4. Remove both the upper and lower shrouds from the steering column.
  5. Remove the Steering Control Module (SCM) from the steering column.
  6. Remove the two screws that secure the left multifunction switch to the SCM .
  7. Disengage the two retaining tabs , next to the screw mounts that secure the left multi-function switch to the SCM.
  8. Disconnect the left multi-function switch from the SCM.
To install:
  1. Position the left multi-function switch onto position on the Steering Control Module (SCM) .
  2. Engage the two retaining tabs, next to the screw mounts that secure the left multi-function switch and firmly snap into place.
  3. Install the two screws that secure the left multifunction switch to the SCM. Tighten the screws to 22 inch lbs. (2.5 Nm).
  4. Position the lower steering column shroud to the underside of the steering column.
  5. Install the three screws that secure the lower steering column shroud to the multi-function switch mounting housing. Tighten the screws to 17 inch lbs. (2 Nm).
  6. Position the upper column shroud over the steering column with the hazard warning switch button inserted through the hole in the upper shroud.
  7. Align the snap features on the upper and lower shrouds and apply hand pressure to snap them together.
  8. Reconnect the battery negative cable.

Dec 22, 2013 | 1999 Jeep Grand Cherokee

1 Answer

Replace turn signal switch


Ensure lever is in center of off position.Disconnect negative battery cable. Disable airbag system. Remove steering wheel. Remove lower and upper column covers. Remove lock cylinder if necessary. Remove wiring harness strap. disconnect steering column electrical connectors. Disconnect turn-signal and multi-function switch Gray and Black connectors. Remove turn-signal and multi-function switch from vehicle.

Jun 05, 2011 | 1998 Chevrolet K1500

1 Answer

What are the instructions to remove and replace the combo turn signal switch, located in the steering column, for a 1999 bravada


Warning: 1995 and later models are equipped with an airbag. Always turn the steering wheel to the straight ahead position, place the ignition switch in Lock and remove key, then remove the airbag fuse and unplug the yellow Connector Position Assurance (CPA) connector at the base of the steering column before working in the vicinity of the impact sensors, steering column or instrument panel to avoid the possibility of accidental deployment of the airbag, which could cause personal injury. The yellow wires and connectors routed through the instrument panel are for this system. Do not use electrical test equipment on these yellow wires or tamper with them in any way while working under the instrument panel.
Caution: On models equipped with a Delco Loc II anti-theft audio system, be sure the lockout feature is turned off before performing any procedure which requires disconnecting the battery.

  • The turn signal switch function is incorporated into the multi-function switch, along with the wiper/washer and headlight dimming controls.
  • Disconnect the negative battery cable. Remove the steering column covers and the drivers knee bolster.
  • Remove the two Torx screws securing the multi-function switch to the top of the steering column.
  • Clip the wire-ties securing the multi-function switch harness to the other steering column wires.
  • At the bottom of the steering column, remove the bolt securing the large bulkhead electrical connector to the firewall.
  • Separate the two multi-function switch connectors from the large bulkhead connector.
  • The multi-function switch and its harness must be replaced as a unit.
  • Installation is the reverse of removal

Mar 16, 2011 | 1999 Oldsmobile Bravada

1 Answer

How do I replace the turn signal multi-function switch in my 1998 Ford Expedition


SECTION 211-05: Steering Column Switches 1998 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/11/2000 Multifunction Switch Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the ignition switch lock cylinder (11582).
    1. Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
    1. Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.
    gj0845a.gif
  1. Twist the tilt wheel handle and shank (3F609) and remove.
    gj0846a.gif
  1. NOTE: Move gear selector to lowest position to access steering column opening cover.
    Release the four clips and remove the steering column opening cover.
    gj0847a.gif
  1. Remove the upper and lower steering column shrouds.
    1. Remove the three screws.
    1. Remove the lower steering column shroud.
    1. Remove the upper steering column shroud.
    gj0976a.gif
  1. Remove the multi function switch.
    1. Remove the two screws.
    1. Disconnect the electrical connectors.
    1. Remove the multi function switch.
    gj0848a.gif
Installation
  1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
    To install, reverse the removal procedure.
    gj0850a.gif

2010&c18=modelyear&c20=n130593&c35=wsm%2cmultifunction%20switch%2cswj%2c211-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 08, 2011 | 1998 Ford Expedition

1 Answer

2001 jeep grand cherokee laredo, lights come one intermittently, horn came on unexpectedly and wouldn't turn off. How do I fix that?


Lights intermittent can be caused by switch or relay. Try swapping the Low Beam relay with another similar relay (horn relay is a good choice) to see if that resolves it. These relays are in the Junction Block--may be under the hood or in the car but not in the big box by the battery). If this doesn't fix it, the problem is likely the headlamp switch.

Horn coming on is usually caused by a broken switch or stripped wire insulation inside the steering column. You would usually have to take the steering wheel off to fix it, and this requires special tools; however, if the problem happens to be under the steering column shroud, you may be able to fix it without taking off the steering wheel. Take the shroud off and see if you can follow the black/red horn wire. Follow it as far as you can to check for stripped insulation contact with any metal. If you lights switch is bad, you can also change that while you have the shroud off.

Please let me know if you have questions.


jturcotte_35.gif
jturcotte_36.gif


Wand Removal & Installataion

  1. Disconnect and isolate the battery negative cable.
  2. Remove the knee blocker from the instrument panel.
  3. Remove the three screws that secure the lower steering column shroud to the upper shroud.
  4. If the vehicle is equipped with a standard non-tilt steering column, loosen the two upper steering column mounting nuts. If the vehicle is equipped with the optional tilt steering column, move the tilt steering column to the fully lowered position.
  5. Remove both the upper and lower shrouds from the steering column.
jturcotte_37.gif

Fig. Steering column shroud removal for the Cherokee

  1. Remove the two screws that secure the multi-function switch water shield and bracket to the top of the steering column.
  2. Remove the one screw located below the left multi-function switch control stalk that secures the multi-function switch water shield and bracket to the steering column.
  3. Gently pull the lower mounting tab of the multi-function switch water shield bracket away from the steering column far enough to clear the screw boss below the left multi-function switch control stalk.
  4. Lift the water shield and bracket with the left multi-function switch off of the left side of the steering column far enough to access the two instrument panel wire harness connectors for the left multi-function switch.
    NOTE If the vehicle is equipped with the optional tilt steering column, lifting gently upward on the tilt release lever will provide additional clearance to ease left multi-function switch removal.
  5. Disconnect the two instrument panel wire harness connectors from the left multi-function switch connector receptacles.
  6. Remove the left multi-function switch and water shield from the steering column as a unit.
  7. Gently and carefully remove the water shield from the switch by pulling it over the hazard warning switch button and the left multi-function switch control stalk.

To install:
  1. Gently and carefully install the water shield onto the switch by pulling it over the hazard warning switch button and the left multi-function switch control stalk.
  2. Position the left multi-function switch and water shield near its mounts on the steering column as a unit.
  3. Reconnect the two instrument panel wire harness connectors to the left multi-function switch connector receptacles.
  4. Position the left multi-function switch onto its mounts on the left side of the steering column.
    NOTE If the vehicle is equipped with the optional tilt steering column, lifting gently upward on the tilt release lever will provide additional clearance to ease left multi-function switch installation.
  5. Position the lower mounting tab of the multi-function switch water shield bracket to the steering column screw boss below the left multi-function switch control stalk.
  6. Install and tighten the one screw located below the left multi-function switch control stalk that secures the multi-function switch water shield and bracket to the steering column.
  7. Tighten the screw to 10 inch lbs. (1.1 Nm).
  8. Install and tighten the two screws that secure the multi-function switch water shield and bracket to the top of the steering column [Tighten the screws to 20 inch lbs. (2.2 Nm)].
  9. Position both the upper and lower shrouds onto the steering column.
  10. Install and tighten the three screws that secure the lower steering column shroud to the upper shroud. Tighten the screws to 18 inch lbs. (2 Nm).
  11. If the vehicle is so equipped, tighten the two nuts that secure the non-tilt steering column upper mounting bracket to the dash panel steering column support bracket studs. Tighten the nuts to 200 inch lbs. 22 Nm).
  12. Reinstall the knee blocker onto the instrument panel.
  13. Reconnect the battery negative cable.

Nov 04, 2010 | 2001 Jeep Cherokee

1 Answer

How to replace the multifunction switch of a 2006 Dodge Ram


REMOVAL
WARNING: To avoid serious or fatal injury on vehicles equipped with airbags, disable the Supplemental Restraint System (SRS) before attempting any steering wheel, steering column, airbag, seat belt tensioner, impact sensor, or instrument panel component diagnosis or service. Disconnect and isolate the battery negative (ground) cable, then wait two minutes for the system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the SRS. Failure to take the proper precautions could result in accidental airbag deployment.

1. Disconnect and isolate the battery negative cable.
2. Remove the screw (2) that secures the tilt steering column knob (1) and remove it from the tilt actuator (3) on the left side of the column.
3. From below the steering column, remove the two outboard screws that secure the upper column shroud (1) to the lower shroud (3).
4. Using hand pressure, press inward on both sides of the upper shroud above the parting line of the lower shroud to release the snap features that secure the two shroud halves to each other.
5. Remove the upper shroud from the lower shroud and the steering column.
6. Remove the one center screw that secures the lower shroud to the steering column (4).
7. Remove the lower shroud from the steering column.
8. Disconnect the wire harness connector (2) from the back of the multi-function switch housing (1).
9. Rotate the steering wheel far enough to access and remove the two screws (4) that secure the switch to the multi-function switch mounting housing (3).
10. Grasp the switch control stalk and pull it toward the left side of the vehicle to remove the switch from the mounting housing.

INSTALLATION
1. Slide the multi-function switch (1) into the multi-function switch mounting housing (3) from the left side. Be certain that the alignment pins on the top and bottom of the switch are properly engaged in the channels of the mounting housing.
2. Rotate the steering wheel far enough to install and tighten the two screws (4) that secure the switch to the mounting housing. Tighten the screws to 2 N·m (20 in. lbs.).
3. Reconnect the wire harness connector (2) to the back of the switch housing.
4. Position the lower shroud (3) onto the steering column (4).
5. From below the steering column, install and tighten the one center screw that secures the lower shroud to the steering column. Tighten the screw to 2 N·m (20 in. lbs.).
6. Position the upper shroud (1) onto the steering column over the lower shroud. On vehicles equipped with an automatic transmission, be certain to engage the gearshift lever gap hider into the opening in the right side of both shroud halves.
7. Align the snap features on the upper shroud with the receptacles in the lower shroud and apply hand pressure to snap them together.
8. Install and tighten the two outboard screws that secure the upper shroud to the lower shroud. Tighten the screws to 2 N·m (20 in. lbs.).
9. Position the tilt steering column knob (1) onto the tilt adjuster actuator (3) on the left side of the steering column, then install and tighten the screw (2) to secure the knob to the actuator. Tighten the screw to 2 N·m (20 in. lbs.).
10. Reconnect the battery negative cable.

Sep 14, 2010 | 2006 Dodge Ram 1500

3 Answers

I am remove heater core from nissan xterra 2000 do i need to remove the evaporator


2000-02 Frontier And Xterra
  1. Disconnect both the negative (1st) and positive (2nd) battery cables.
  2. Remove the steering wheel by performing the following procedure:
    1. Turn the ignition switch to the OFF position.
CAUTION Wait 3 minutes after disconnecting the battery cables and turning the ignition switch to the OFF position before servicing the air bag system.
  1. Remove the lower lid and disconnect the driver-s air bag module connector.
  2. Remove both side lids.
  3. Using the Tamper Resistant Torx® Wrench size T50, remove the special bolts from both sides of the steering wheel and discard them.
  4. Remove the SRS module from the steering wheel.

CAUTION Always store the SRS module face up.
  1. Position the steering wheel in the straight-ahead position.
  2. Disconnect the horn connector and remove the steering wheel nut.
  3. Using a steering wheel puller, press the steering wheel from the steering column.
  1. Remove the passenger-s side air bag by disconnecting or removing the following items:
    1. Turn the ignition switch to the OFF position.
CAUTION Wait 3 minutes after disconnecting the battery cables and turning the ignition switch to the OFF position before servicing the air bag system.
  1. Open the glove box door.
  2. Working inside the glove box, open the lower instrument panel lid.
  3. Remove the passenger-s air bag module connector clip from the lid.
  4. Disconnect the passenger-s SRS module connector.
  5. Remove the glove box and the lower passenger-s side instrument panel.
  6. Using the Tamper Resistant Torx® Wrench size T50, remove the SRS module-to-instrument panel special bolts and discard them.
  7. Remove the 4 SRS module-to-instrument panel mounting nuts.
  8. Release the SRS module-to-instrument panel clips and remove the SRS module.
CAUTION Always store the SRS module face up.
  1. Drain the cooling system into a clean container for reuse.
  2. Working inside the engine compartment, disconnect the 2 heater hoses from the heater core.
  3. Discharge and recover the air conditioning system refrigerant.
  4. Disconnect both refrigerant lines from the evaporator core. Plug the lines to prevent moisture from entering the system.
  5. Remove the glove box and the mating trim.
  6. Disconnect the thermal amp connector.
  7. emove the air conditioning housing assembly from the vehicle.
  8. Remove the instrument panel assembly by performing the following procedure:
    1. Remove the 4 steering column cover screws; then, separate and remove the steering column covers.
    2. Remove the 2 driver-s side lower instrument panel screws and the lower instrument panel.
    3. Remove the 4 cluster cover screws and the cluster cover.
    4. Remove the 6 combination meter screws; then, disconnect the combination meter electrical connector and remove the meter.
    5. Remove the 2 glove box screws and the glove box.
    6. Remove the 2 instrument stay cover screws; then, disconnect the electrical harness connectors and remove the stay cover.
    7. Remove the 2 cluster lid -C- screws; then, disconnect the electrical harness connectors and remove the cluster lid -C-.
    8. Remove the 4 audio and deck pocket screws; then, disconnect the electrical harness connectors and remove the audio and deck pocket.
    9. Disconnect the ASCD main switch connector.
    10. Remove the 2 meter cover screws; then, disconnect the electrical harness connectors and remove the meter cover.
    11. Remove the 4 air conditioning-heater control screws; then, disconnect the control cables and remove the air conditioning-heater control.
    12. Remove the front pillar garnish.
    13. Remove the 3 instrument panel assembly nuts and 2 bolts; then, remove the instrument panel.
  9. Remove the heater housing assembly.
  10. Remove the heater core from the heater housing assembly.

continue...

Jul 16, 2010 | 2000 Nissan Xterra

1 Answer

How to replace the multi function switch on my 2004 optima kia...any demonstration/illustrations will be appreciated


Kia_Sephia_Rio_Spectra_Optima_1998-2006
Multi-Function Switch - Removal & Installation

  1. Disconnect the negative battery cable.
  2. Remove the steering wheel, as outlined earlier in this section.
  3. Remove the steering column upper and lower shrouds.

    29391c9.jpg
    Fig. Remove the steering column upper (A) and lower shrouds (B)
  4. Detach the multi-function switch electrical connector(s).

    0b41ec5.jpg
    Fig. Detach the multi-function switch (A) electrical connector(s)
  5. Remove the 3 bolts, as shown, then remove the multi-function switch assembly (B).
  6. Installation is the reverse of the removal procedure.

    4bfd90f.jpg
    Fig. Remove the 3 bolts, as shown, then remove the multi-function switch assembly (B)

Hope this help (remember rated this post).

Mar 28, 2010 | 2004 Kia Optima

1 Answer

How do I install headlight switch on 95 mercury tracer?


  • Headlamps Inoperative
  • Fuse.
  • Headlamp switch.
  • Headlamp relay.
  • Circuit.
  • Bulbs.

Section 11-05: Steering Column Switches 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Multi-Function Switch
Removal
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR AIR BAG DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY GROUND CABLE MUST BE DISCONNECTED PRIOR TO SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS.
    Disconnect the battery ground cable (14301) and wait one minute for the backup power supply to be depleted.
  1. Remove the steering wheel (3600). Refer to Section 11-04 for the removal procedure.
  1. Remove the four screws from the lower steering column shroud (3530).




  1. Remove the ignition switch lock cylinder illumination lamp socket from the lower steering column shroud.
  1. Remove the lower steering column shroud.
  1. Remove the upper steering column shroud.
  1. Disconnect the three multi-function switch electrical connectors.
  1. Remove the multi-function switch screws.
  1. Remove the multi-function switch electrical connectors and the multi-function switch (13K359).

Jan 16, 2009 | 1995 Mercury Tracer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

723 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...