Question about 1991 Chevrolet Cavalier

Open Question

The horn in 1991 chevrolet cavalier z24 - 1991 Chevrolet Cavalier

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
csmock132
  • 4669 Answers

SOURCE: My 1991 cavalier z24 with 3.1 will not start, has

Can you unplug one of the injectors to check for injection pulse. You should be able to unplug number 1 (next to the alternator) and number 6

Posted on Mar 25, 2009

Ad
GM Elec
  • 1000 Answers

SOURCE: I need to tear down

Below is process for removing and replacing the clutch assembly.
Hope this helps, good luck.
Regards,


REMOVAL & INSTALLATION


See Figures 1, 2 and 3



0900c1528003be16.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Exploded view of the clutch disc and cover assembly

  1. Disconnect the negative battery cable.
  2. If equipped with a cable clutch (1982-84 vehicles), disconnect the cable at the clutch release lever and transaxle, as outlined earlier in this section.
  3. For 1985-94 vehicles remove the sound insulator from inside the vehicle. Disconnect the clutch master cylinder pushrod from the clutch pedal.




0900c1528003be17.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Disconnect the clutch actuator (slave) cylinder line - 1995-96 vehicles
  1. Remove the transaxle, as outlined earlier in this section.
  2. Mark the pressure plate assembly and the flywheel so that they can be assembled in the same position. They were balanced as an assembly at the factory.
  3. Loosen the attaching bolts one turn at a time until spring tension is relieved.
  4. Support the pressure plate and remove the bolts. Remove the pressure plate and clutch disc. Do not disassemble the pressure plate assembly; replace it if defective.
  5. Inspect the flywheel, clutch disc, pressure plate, throwout bearing and the clutch fork and pivot shaft assembly for wear. Replace the parts as required. If the flywheel shows any signs of overheating, or if it is badly grooved or scored, it should be refaced or replaced.




0900c1528003be18.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: You must follow the specified sequence when tightening the pressure plate retaining bolts
To install:
  1. Clean the pressure plate and flywheel mating surfaces thoroughly.
  2. Position the clutch disc and pressure plate into the installed position, and support with a dummy shaft or clutch aligning tool, tool J 29074 or equivalent. The clutch plate is assembled with the damper springs offset toward the transaxle. One side of the factory supplied clutch disc is stamped "Flywheel Side".
  3. Install the pressure plate-to-flywheel bolts. Tighten them in the sequence shown in the accompanying figure, as follows:
    1. Tighten bolts 1,2,3, then 4,5,6 in the sequence shown to 12 ft. lbs. (16 Nm).
    2. Tighten bolts 1,2,3, then 4,5,6 in the sequence shown to 15-22 ft. lbs. (22-30 Nm) plus an additional 30° turn.
    3. Remove the clutch alignment tool.

  4. Lubricate the outside groove and the inside recess of the release bearing with high temperature grease. Wipe off any excess. Install the release bearing.
  5. Install the transaxle, as outlined earlier in this section.



WARNING When adjusting the cruise control switch, do NOT exert an upward force on the clutch pedal pad of more than 20 lbs. (89 N) or damage to the master cylinder pushrod retaining ring may result.

  1. For 1985-94 vehicles, attach the clutch master cylinder pushrod to the clutch pedal and secure with the retaining clip. If equipped with cruise control, check the switch adjustment at the clutch pedal bracket. Install the sound insulator.
  2. If equipped with a cable clutch, attach the clutch cable at the transaxle and clutch release lever. Check the clutch operation by lifting the clutch pedal up to allow the mechanism to adjust the cable length. Depress the pedal slowly a few times to set the pawl into mesh with the quandrant teeth.


ADJUSTMENTS


All 1982-84 models have a self-adjusting clutch mechanism located on the clutch pedal, eliminating the need for periodic free play adjustments. The self-adjusting mechanism should be inspected periodically as follows:
  1. Depress the clutch pedal and look for the pawl on the self-adjusting mechanism to firmly engage the teeth on the ratchet.
  2. Release the clutch. The pawl should be lifted off of the teeth by the metal stop on the bracket.

On 1985 and later models, the hydraulic clutch system provides automatic clutch adjustment. No adjustment of clutch linkage or pedal position is required.

Posted on May 04, 2009

  • 299 Answers

SOURCE: 1999 Chevy Cavalier Horn Relay Location

should be in underhood junktion block.

Posted on Jun 17, 2009

michigan man
  • 3533 Answers

SOURCE: I NEED WIRING DIAGRAM FOR CHEVROLET CAVALIER

give these websites a try its www.autozone.com and www.alldatadiy.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Posted on Nov 04, 2009

Testimonial: "THANKS"

  • 1608 Answers

SOURCE: my 1991 cavalier z24 with 3.1 fires but wont

The fuel pressure specs.for this engine is 41-47psi.This is with the key on and engine off.If you want to make sure it is not fuel related then spray some carb.cleaner or brake cleaner into the throttle body and then see if it starts for a few seconds then it is the fuel pump.hope this helps.

Posted on Dec 15, 2009

Testimonial: "thank you.i will try a new fuel pump,"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

TRYING TO FIND THE HORN UNDER THE HOOD, HORN BEEPS INTERMITTENTLY WHILE DRIVING. 1991 CHEVY CAVALIER


LOOK UNDER FRONT BUMPER FASCIA FOR CAR HORN.HORN KEEP BLOWING COULD BE STICKING RELAY OR HORN BUTTON CONTACTS STICKING.

Aug 13, 2011 | 1991 Chevrolet Cavalier

1 Answer

I need to know my firing order for a 1991 chevy cav 4cy 2.2l


1991 Chevrolet Cavalier/Z24 2.2 liter L4 VIN "G"

zjlimited_23.gif

Hope this helps; remember to rate and comment this answer. Good luck.

Nov 17, 2010 | 1991 Chevrolet Cavalier

1 Answer

Need to know the firing order on 1991 z24 cavalier 3.1 multi port fi


1991 Chevrolet Cavalier/Z24 3.1 liter V-6 VIN "T"

a400dd8.gif


Hope this helps (remember rated and comment this).

Aug 31, 2010 | 1991 Chevrolet Cavalier

1 Answer

Where is the fuse chart for a 1991 chevy cavalier z24


on the side of dash on drivers side should be a panel

Mar 05, 2010 | 1991 Chevrolet Cavalier

1 Answer

I need to Know where the speedometer sensor is on a 1991 chevy cavalier Z24 3.1 mutiport with an Automatic transmission 2WD


The speed sensor for your 1991 Chevy Cavalier Z24 is located on the transmission just inboard of where the passenger side drive axle enters the trans-axle.

Feb 16, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

My 1991 cavalier z24 with 3.1 will not start, has fuel and spark, turns over okay, but will not start. changed the coil pack and still nothing


Can you unplug one of the injectors to check for injection pulse. You should be able to unplug number 1 (next to the alternator) and number 6

Mar 25, 2009 | 1991 Chevrolet Cavalier

1 Answer

Horn not grounded?


the clicking noise is the horn relay, this means in most cases the horn is defective and should be replaced.

Mar 23, 2009 | 1999 Chevrolet Cavalier

2 Answers

Horn won't work but, use to. Was going to check the fuse first, but no car book and fuses don't indicate which is for horn. Got any ideas?


I had the same problem eith my '90 cavalier 2.2L and all I did to fix it was replace the relay. Mine was located right behind the fuse kick panel by the driver door. There should be two relays: a round one and a square one. The square one is most likely the horn relay. Hope this helps

Aug 01, 2008 | 1990 Chevrolet Cavalier

Not finding what you are looking for?
1991 Chevrolet Cavalier Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...