Question about 1984 Ford F 150

Open Question

HOW TO CHANGE REAR AXLE BEARING 1984 FORD F150

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Rear Axle Bearing

i know for a fact that the bearing comes with the hub., and if the old bearing is badly damage you may need to heat it to remove it from the axel...so this may be a rather big job if your not equipt
with torch or other ...

Posted on May 31, 2008

  • 625 Answers

SOURCE: help with repairs on my ford f150 1984

you can also try autozone.com and shoul be hable to find some info thanks

Posted on Nov 05, 2008

heavymetal77
  • 721 Answers

SOURCE: rear axle leaking

Block the front tires. Break the rear lugs loose. Jack up the rear of the truck at the center if possible. remove the wheels & brake drums. Remove the brake shoes,return springs & all the other hardware. Remove the differential cover & drain oil. If you have a posi the next step sucks. You need to remove the threaded pin from the housing & remove the axle retaining clips. All the while,being carefull of the spring in the posi unit. If no posi,then same procedure,minus the "pucker factor". After the axle is out,take a large flat blade screw driver or pry bar & pop the seal out. Keep in mind the axle bearing is probably gone too , so that's another procedure. Keep it apart,you'll be glad you did.

Posted on Jun 23, 2009

  • 506 Answers

SOURCE: rear brakes on 2006 f150 need changing

There should be two bolts that hold the caliper to the axle assembly. Remove these two bolts and slide the caliper off. At this point check the rotors for abnormal wear or grooves. Depending on how many miles you have on them I would replace them regardless. Before you insert the new pads into the caliper I like to use a C clamp and a piece of flatstock to force the pistons back to their original location. If you don't do this you will not be able to fit the caliper over the rotor. Before installing the caliper if you did buy the new rotors use some brake cleaner to remove any of the cosmoline oil that they are shipped with. Remember to chock your front wheels or use jackstands if you have enough. Good luck!

Posted on Feb 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace wheel cylinder on 1984 350 ford van rear driver side


for the axle or the brakes? Changing a brake cylinder is much easier than a wheel bearing.

Jan 11, 2015 | Ford Cars & Trucks

1 Answer

High pitch nosie from rear end of 2004 ford f-150 supercrew


Does the sound change while accelerating or decelerating?? If it does i would suspect a carrier bearing or a pinion bearing going bad..If its consistant,,and doesnt change with acceleration or deceleration,,then it may be a axle bearing..

Sep 29, 2011 | 2004 Ford F150

1 Answer

How to remove rear wheel bearings on my 1999 Ford Expedition and how do i know what pulley to rent/buy?


The 1999 Ford Expedition is built on an F150 platform. The Expedition uses a 9.75-inch rear axle. The axles are retained with C-clips at the end of the axle shaft, inside the differential carrier. The axle bearings are of the roller type. A failed axle bearing can manifest itself as a noise at the rear wheel or gear oil leaking past the oil seal. When replacing axle bearings, the oil seals must also be replaced.
Torque the caliper mounting bolts to 30 foot-pounds. Torque the bolt to 20 foot-pounds with a torque wrench and socket. Click this link below for complete detailed procedure:--- http://technoanswers.blogspot.com/2011/06/how-to-remove-rear-wheel-bearings-on.html -------------- This should help.Thanks.Helpmech.

Jun 07, 2011 | Ford Expedition Cars & Trucks

2 Answers

I have a 2002 Ford F 150 Supercrew. There is a whining noise in the rear axle. What causes this noise?


Fisrt thing to check is the differential fluid, make sure it is full up to the plug. If this is dry you could have ruined a bearing in the rear end. Next check all the rear axle bearings. Most likely it is the differential and the gears are dry and when they dry out they scorch and cause a noise like this.
If no issue found in the rear end it may possibly a bearing in the tranny. These noises travel through the steel and sometimes get confusing as to where they originate from.

May 26, 2011 | 2004 Ford F150

1 Answer

How to change the rear axel bearrings on ford f 1=150


have to pull the diff cover,remove the small bolt that holds the pin,remove the pin . With wheels off ,push the axle in remove c-clip ,slide axle out. You will need a slide hammer to remove the bearing.(or pull both sides and drive out with a long piece of rebar from the other end)
Be sure to check the axle surface where the bearing rides,if is damaged the parts stores sell a repair bearing that makes the rollers ride in a different spot on the axle.(called "axle savers")

Nov 06, 2010 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Rear differential on f150 is leaking,how do i reseal it?(1984 f150 4x4)


If its leaking from the front where the drive-shaft connects, it needs a new pinion seal. If its leaking from the rear cover you need to remove cover and replace the gasket. If its leaking at the wheels you need to replace the axle seals.

May 16, 2010 | 1984 Ford F 150

1 Answer

How do you change the bearings on the rear axle of a f150 Ford pickup? And does my year model require the bearings to be pressed on?


you have to block up the rear end then pull the cover off the rear end then pull tires and drums off then
go to the punkin and pull the center pin out its a 5/16 or 8mm bolt out slid the pin out then push axles in take the C-clips out then pull axles out
you will need a axle slide hammer to get the bearing out and
then tap the new one in just far enough to get the cyl. in
then put all back to gether

Mar 07, 2010 | 1996 Ford F150 Regular Cab

1 Answer

Feels like chatter in rear end when accelerating 2004 f150 4x4


Check the "U-Joints" on the drive shaft and or rear wheel/axle bearings.
You MAY need a little help as the wheel(s) needs to be of the ground to check axle bearing. Grasp top and bottom of the tire and wobble it in and out.

Dec 20, 2009 | 2004 Ford F150

1 Answer

Remove and replace rear wheel bearing on 1997 f150


REMOVE DIFF COVER ON 3rd MEMBER THERE WILL BE A SMALL 8mm BOLT REMOVE BOLT SLID PIN OUT PUSH AXLE IN AND REMOVE HORSE CLIP DO SAME FOR OTHER SIDE PUSH AXLE IN REMOVE CLIP. YOU'LL NEED A BEARING PULLER TO REMOVE BEARING INSTALL NEW BEARINGS WITH NEW SEAL, INSTALL BOTH AXLE WITH HORSE CLIPS INSTALL PIN AND 8mm BOLT, COVER AND REFILL.

Nov 04, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Rear seal and bearing leaking on passenger side.


Basic to get tire and hub off, remove rear diff cover remove bolt, remove clip, pull axle out, then heavy puller to pull bearing and seal. Ck axle for wear

Sep 16, 2009 | 2001 Ford F150 Styleside SuperCrew

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...