Question about 1999 Chrysler 300M

1 Answer

Need step by step on how to remove water pump on 1999 chrysler 300

Taking out water pump on 1999 chrysler 300

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chrysler Master
  • 14,417 Answers

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 51 Answers

SOURCE: 1999 chrysler t&c needs a fuel pump

yes you need to drop the tank i worked for chrysler for a few years and i tried everything to try to slip the pump out with out fulling removing the tank and in the end its just easier to take the whole thing out.

Posted on Mar 15, 2009

  • 4669 Answers

SOURCE: I need to replace water pump on 1995 Chrysler Le Baron

This will take some digging. You would be money ahead to go to a parts store and buy a haynes or chilton manual for 20 dollars. The waterpump is ran by the timing belt, so you will want to replace that to. You also need to know how to line the timing marks up to get the belt back on right. The manual will give you all the info you need.

Posted on Apr 08, 2009

  • 6784 Answers

SOURCE: The car cranks but won't start

Ok, check the following below--

1. Check the Ignition control Module for its operational value. it may be damaged.

2. Check the coils.
3. Check the plugs and wires.
4. Check the ECM/PCM/ECU(All represent the same device that is commonly known as the engine control computer)

Check these areas thoroughly for faults. I would also advise to replace the fuel filter and fuel pump as well.

Posted on May 31, 2009

  • 564 Answers

SOURCE: i need torque specs to change a water pump for a

dont know the specs but you should be ok if you tighten the bolts snuggly and then 1/2 turn this will usually suffice just be careful not to over tighten

Posted on Nov 01, 2009

  • 1654 Answers

SOURCE: Need a step by step instruction with picture if

it is threaded into the left side valve cover (front 1) you remove th hose and use a wrench. dont over tighten new part the valve cover is plastic.

The pcv valve will be right on top of the intake manifold center when you are standing

looking straight in at the engine as you raise the hood. Also, as you stand at the

front of the car looking in, follow the black hose that comes out of the front

valve cover, on the opposite side of the oil fill cap. That hose goes up to the pcv

valve. The valve is screwed into the intake manifold at that point.

very easy repair!

Posted on Dec 05, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you replace the fuel pump in a Chrysler 300m?

  1. Disconnect the Battery
  2. Drain the fuel from the Tank
  3. Raise the rear of the car and support with 2 jack stands
  4. Remove the Tank
  5. Remove the Old Pump
  6. Install the New Pump
  7. Reinstall the Tanks.
How to Remove and Replace Chrysler 300 Gas Tank And Fuel Pump

May 05, 2016 | 1999 Chrysler 300M

1 Answer

How do i reset the security system on my 1999 chrysler 300 m

sound like run battery down your water pump on the 300M driven by the timing chain.could have disturb timing.

Apr 06, 2013 | Chrysler Cars & Trucks

1 Answer

Presure test the radiator 1999 chrysler 300 can not find water leak, replased water pump

it very well could be a blown head gasket and its leaking into the piston

Dec 05, 2012 | 1999 Chrysler 300M

1 Answer

Need to know where the water pump is located on the engine 3.5

the water pump is located front vehical under a cover u have to remove ththe belt&PULLEYtensoiner to get cover off &then you see the two cam mark pullies than losin the plusher to release the belt water pump is the center it take 2.5 hour to complete the job

Jun 27, 2012 | 1999 Chrysler LHS

2 Answers

2005 Chrysler 300 Fuel pump removal replacement

There is a company that independent auto repair shops get their information from, this same information is available inexpensively for people that work on their own cars.. The information is year make and model specific, covering repair procedures, torque specifications, fluid capacities and specifications, service bulletins, component locations, wiring diagrams ect.... Alldata is very easy to navigate

Oct 14, 2011 | 2005 Chrysler 300

1 Answer

I am trying to change my oil filter on my 1999 chrysler 300, but it is secured by two bars side by side and a water hose under it. what do i need to do?

The oil filter is attached to that. what you are talking about is the oil cooler. don't take this off. The oil filter will unscrew from this.

Feb 07, 2011 | 1999 Chrysler 300M

1 Answer

How to remove waterpump?


STEP 1, You have to locate the water pump first which is located just above the air comperssor.

STEP 2. Take timing cover off.

STEP 3. Take out the motor mount.
STEP 4. Remove the harmonic balancer

Remove the water pump hosing by loosing a few bolts(about 4 oR 5)that holds it.

STEP 6 Remove the timing chain techner.

STEP 7 Loosen out the three nuts that holds the water pump in its place, pull out the water pump and replace,follow the reverse instructions to assemble.

Best of luck..

Aug 21, 2010 | 1999 Chevrolet Malibu

2 Answers

Need step by step to replace water pump on 1997 dodge caravan v-6 3,0 mits. motor...

Chrysler Caravan/Voyager/Town and Country 1996-1999 Water Pump - REMOVAL & INSTALLATION
3.0L Engine
See Figure


Fig. 3: Water pump mounting detail-3.0L engine
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the drive belts. Remove the timing belt covers and the timing belt.
  4. Remove the water pump mounting bolts.
  5. Separate the water pump from the water inlet pipe and remove the water pump.
  6. Inspect the water pump and replace as necessary.

To install:
  1. Clean all gasket and O-ring surfaces on the water pump and water pipe inlet tube.
  2. Wet a new O-ring with water and install it on the water inlet pipe.
  3. Install a new gasket on the water pump.
  1. Install the pump inlet opening over the water pipe and press until the pipe is completely inserted into the pump housing.
  2. Install the water pump-to-block mounting bolts and tighten to 20 ft. lbs. (27 Nm).
  3. Install the timing belt and timing belt covers. Install and adjust the drive belts.
  4. Reconnect the negative battery cable. Fill the cooling system to the proper level with a 50 / 50 mixture of clean, ethylene glycol antifreeze and water.
  5. Run the engine and check for leaks. Top off the coolant level, if necessary.

Hope this help (remember comment and rated this).

Apr 13, 2010 | 1997 Dodge Grand Caravan

Not finding what you are looking for?
1999 Chrysler 300M Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides