Question about Cars & Trucks

Open Question

1930 model a ford tudor sedan/ vacuum wiper tubing diagram

Vacuum tubing assembly diagram/1930 model a ford tudor sedan

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
raineman_15
  • 273 Answers

SOURCE: NEED HOW TO DIAGRAM OR SCHEMATICS FOR INSTALLING

Removal

  1. Disconnect battery ground cable
  1. Remove the steering column shroud
  1. Remove two self-tapping screws that attach the multi-function switch to the steering column tube casting. Disengage multi-function switch from casting.
  1. Disconnect the two electrical connectors, using caution not to damage the locking tabs. Do not damage PRNDL cable.
    raineman_15_19.gif

1
Steering Column 2
Screw 3
Multi-Function Switch 4
Wiring to Multi-Function Switch A
Tighten to 2-3 Nm
(18-27 Lb-In)


Installation

  1. Install the two switch electrical connectors to full engagement. The wiring for the switch is to be routed under the PRNDL cable.
  1. Align the mounting holes on multi-function switch with the holes in the steering column tube casting. Install two self-tapping screws making sure to start the screws in the previously tapped holes. Tighten to 2-3 Nm (18-27 lb-in).
  1. For automatic transmission (7003), verify that the PRNDL adjustment is correct.
  1. Install the steering column shroud.
  1. NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more for powertrain control module to relearn the strategy.
  2. Connect the battery ground cable.
  3. Check the steering column tube for proper operation.

I hope this helps, if you have any questions just ask

Posted on Jan 01, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 ford 150 . wipers don't work but washer still does work . could it be a fuse or wiper motor. or what? Ted H ope you can help thanks


Do you know how to test automotive electrical circuits ! Using a wiring diagram and a volt meter ? test power to the wiper motor .
Control from the switch .
http://www.bbbind.com/free_tsb.html free wiring diagrams . Enter vehicle info. year , make , model an engine size . Under system click body & accessories , subsystem click wiper / washer . click the search button then the blue link . Look at the diagram for pin # 's an wire colors , see fuse at top of diagram . Check B+ power with volt meter . Check the inputs from the wiper switch to the motor . If all the power an inputs are good , replace the wiper motor .

Jun 12, 2017 | Ford Cars & Trucks

1 Answer

2007 Fusion 2.3L with FNR5 transmission I'm looking PCA circuit wiring diagram. Does anyone have it? Your help is very much appreciated. Thanks


Do the diagnostics on the fault code first. You have the Ford emissions system Troubleshooting repair manual correct? If not try eBay for that and a wiring diagram booklet called the Ford Vacuum and Electrical Troubleshooting guide.

Jun 22, 2016 | 2007 Ford Fusion I4 SEL Sedan

1 Answer

Vacuum hose diagram video for 1999 ford explorer


vacuum hose diagram 99 ford explorer Google Search try looking at these pictures and you could also watch some you tube video's for info

Apr 11, 2014 | 1999 Ford Explorer

2 Answers

What is body size


compact.. subcompact.. sedan..tudor.. fourdoor..wagon..coupe..suv..pickup..name one..for what..repost please..

Jan 22, 2013 | Cars & Trucks

1 Answer

Diagram_Schematic--1929 ford model a


For $12:
http://www.amazon.com/dp/B000ITH6I2/?tag=savereviews-20

There's a 1-page free color diagram at:
http://www.webjunk.com/modela/wp-content/uploads/2008/02/wiring-diagramcolor2sm.jpg

but since its a 207KB JPEG file, it exceeds FixYa's 150KB limit.

The wiring diagram of the 1929, 1930 and 1931 Ford Model A's are identical, and are so simple, the entire vehicle's wiring diagram fills just one page.

Oct 23, 2011 | Cars & Trucks

1 Answer

I need to see a picture of vacuum diagrams for the vacuum lines that are reach from the "radio cavity" the blue one is disconnected and I want to reconnect it. the vehicle is 1990 cadillac sedan...


I couldn't find a diagram of those vacuum connections. If only one line is disconnected then look for an open hose nipple on the AC control assembly and that should be where it goes. Those vac lines supply actuators which move diverters in the duct system that activate the different climate control system modes.

Jan 10, 2011 | 1990 Cadillac Deville

1 Answer

Need to replace heater core? how do i remove old one and replace new one?


Here are the instructions with a diagram. If you need to enlarge the diagram save it to your picture files and then enlarge it there.

1. Disconnect battery ground cable, then drain cooling system. See: Engine, Cooling and Exhaust\Cooling System\Service and Repair

2. Disconnect heater hoses from heater core. Plug heater hoses and core fittings to prevent coolant spillage.


3. Remove bolt located below windshield wiper motor, attaching left end of plenum to dash panel.


4. Remove nut attaching upper left corner of evaporator or heater case to dash panel.
5. Disconnect vacuum control system supply hose from vacuum source, then push grommet and hose into passenger compartment.

6. Remove all instrument panel retaining screws and pull instrument panel back as far as possible without disconnecting any wire harnesses.
7. Loosen right door sill plate and remove side cowl trim panel.

8. Disengage temperature control cable housing from bracket on top of plenum. Disconnect cable from temperature blend door crank arm.

9. On models w/Automatic Temperature Control (ATC) , remove cross body brace and disconnect wiring harness from temperature blend door actuator and disconnect ATC sensor tube from evaporator case connector.
10. Disconnect vacuum harness at vacuum connector near floor air distribution duct.

11. Disconnect white vacuum hose from outside recirculating air door vacuum motor.
12. Remove two hush panels.

13. Remove one plastic push fastener retaining floor air distribution duct to left end of plenum. Remove left screw and loosen right screw on rear face of plenum. Remove floor air distribution duct.

14. Remove two screws from rear side of floor air distribution duct to plenum. To remove right screw, it may be necessary to remove the two screws attaching lower panel door vacuum motor to mounting bracket.

15. Remove push fastener attaching floor air distribution duct to left end of plenum, then remove floor air distribution duct.
16. Remove two nuts located along lower flange of plenum.
17. Carefully move plenum rearward, so that heater core tubes and plenum case upper stud clear openings in dash panel, then remove plenum from vehicle by rotating upper portion of the plenum forward, down and out from under instrument panel. It may be necessary to carefully pull lower edge of instrument panel rearward while plenum is being removed from behind instrument panel.
18. Remove retaining screws from heater core cover, then the cover from plenum assembly.

19. Remove retaining screw from heater core inlet and outlet tube bracket.


Heater core removal and installation diagram.




emissionwiz_78.jpg

20. Pull heater core and seal assembly from plenum assembly.
21. Reverse procedure to install.

Jan 06, 2011 | 1993 Mercury Grand Marquis

1 Answer

Wipers on my 1994 Saturn SL1 (SOHC) sedan start fine, but then won't turn off. Is it more likely the motor or the switch? Is there something else to be looking at?


the wiper motor assembly has a park sensor, and if this sensor fails, it will not let wipers park or shut off. ( replace wiper motor assembly).

Aug 08, 2010 | 1994 Saturn Sl

1 Answer

I cannot find a diagram to show the pressure springs proper installation. Spring has slipped out of position and wiper will not fully contact the glass. This is for the 2002 Ford Escape rear wiper. Ray


Have you tried going to the dealership service dept. They should be able to help without charging anything granted you do the installation. If the spring has slipped out of position there is a good chance the spring and/or wiper assembly may be bent, damaged or stretched.

Apr 03, 2009 | 2002 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...