Question about 1999 Pontiac Grand Am GT

Open Question

How to program 1999 grand am gt keyless remote

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: programming new keyless entry remote

Yes...

1) Remove the "MALL PGM" fuse located in the glove compartment (see owners manul for location)

2) Turn ignition switch to "Accessory" then "Off" then back to "Accessory" witin 1 second. (accessory is opposite the forward direction key is normally turned for starting the vehicle)

3) Plug in drivers side seat belt.

4) Open and close a door (will hear a chime indicating in program mode.)

5) Press and hold both the "Lock" and "Unlock" buttons on the Fob and wait at least 7 seconds (may take longer) you'll hear a chirp or the horn will sound.

6) repeat step 5 for all other Fobs.

7) turn key to Off and replace fuse.

Posted on Jun 22, 2008

Ad
MrScary66613
  • 1990 Answers

SOURCE: Keyless Entry for 2003 Grand Am

This is a Dealer Option and they all Charge Different Prices. I have heard of Prices from 50.00 to 175.00 depending on what Options are on the Car.

Posted on Jan 23, 2009

Molson02536
  • 3854 Answers

SOURCE: How to program a keyless remote for a Pontiac

NOTE: You must have the correct part number on the remote for it to work. The part number you need is 15732803.
Transmitter programming per the GM manual:
Before entering the programming mode, verify the possession of all the transmitters you will be using on the vehicle. Once you program the transmitter, the memory erases the other transmitters. You may program up to 4 transmitters.

  1. Turn OFF the ignition switch
  2. Usa a fused jumper (3 amp is sufficient) and connect terminal 8 (back/white wire) to terminal 4 (black wire)
  3. Close all the doors
  4. Turn ON the ignition switch / the doors will lock
  5. Press and hold the following buttons on one of the transmitters for 30 seconds: lock and unlock
  6. After a 30 second delay, the doors will lock and unlock Important: 
    DO NOT turn OFF the ignition . If the switch is turned OFF the first transmitter becomes inoperative.
  7. In order to program extra transmitters repeat Step 5
  8. Disconnect the fused jumper wire from the data link connector
  9.  Turn off ignition
  10. Verify functions of all programmed transmitters.

This should work for the 1997 and 1999 Bonneville's. Good Luck. Keep me posted, be glad to answerer any other questions you may have. 

Posted on Aug 11, 2009

  • 691 Answers

SOURCE: how do you program the remotes for keyless entry

Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:

Sit in the vehicle driver's seat.
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation

Posted on Oct 21, 2009

  • 603 Answers

SOURCE: I tried the program instructions for my keyless

Here's what I found. Go to this page and select 2006 Grand Prix - http://www.programyourremote.com/classified/Browse.asp?cid=273
You can't program I guess, sorry

Posted on Dec 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u find out the keyless entry code if u buy a used 99 grand cherokee ltd without the remote


These have to be programed with a Chrysler scan tool. Most likely only a dealership will have one. You can't program one with out the scan tool. If you need another key this would be the time for that as well as it needs to be programed by the dealer too.

Jun 01, 2012 | 1999 Jeep Grand Cherokee

1 Answer

How do you program a keyless entry remote for 1998 Jeep Grand Cherokee


someof them you cant you have to take it to the dealership

Jan 17, 2012 | 1998 Jeep Grand Cherokee

1 Answer

Keyless remote instructions for 99 pontiac grand prix do not work


Is the battery good in the remote? Is the remote working? Did the car come with keyless remote?
If you stop by a big box part store they have a tester to check the remote. Sometimes when the battery is replaced there is a solder joint that brakes.

Feb 14, 2011 | 1999 Pontiac Grand Prix

1 Answer

I bought a new keyless remote for my jeep and i was wondering if i could program it myself?


yes if you have a good one that is functioning correctly you can refeer to the owners manual under remote keyless entry or alarm section and it will give you a step by step procedure every chrysler jeep dodge has a differant procedure if you cant find it send me a clarification notice and i will look into for you

Jan 10, 2011 | 1999 Jeep Grand Cherokee

1 Answer

I need to re program my key pad to my car it is a 99 grand am. how do i do it?


If your 1999 Grand Am was built late in 1999 you will have to go to a Locksmith or Dealership to get your remote programmed. If your 1999 Grand Am was built eary in 1999 you can use the programming instructions below.
1. Make sure ignition is in the OFF position.
2. Locate the programming connector in the trunk (drivers side). It is a plastic
connector with two wires leading up to it. The connector is not plugged into
anything. You may have to pull back trim to access connector.

3. The programming connector should have two terminals. Connect both terminals
with a suitable jumper wire. Make sure the terminals remain connected
throughout the programming procedure.

4. Press the LOCK and UNLOCK buttons on the remote simultaneously. In response
the Keyless Entry Module will cycle all the Door Lock Motors at once. Your new
remote has been accepted and all existing remotes have been erased.

5. Repeat the previous step for each additional remotes (including any exsisting remotes)
Do not remove jumper wire in between programming of remotes.

6. Remove the jumper wire from the Keyless Remote Connector.


Thank you for using fixya and good luck

May 10, 2010 | 1999 Pontiac Grand Am GT

1 Answer

I tried the program instructions for my keyless


Here's what I found. Go to this page and select 2006 Grand Prix - http://www.programyourremote.com/classified/Browse.asp?cid=273
You can't program I guess, sorry

Dec 18, 2009 | 2006 Pontiac Grand Prix

1 Answer

2005 pontiac grand am wont turn over. headlights and dash lights seem to work good. keyless remote does not work.


ck if you need a tune up, lights work off the battery,charge battery ck electric coil

Oct 27, 2009 | 1999 Pontiac Grand Am GT

1 Answer

How do you program the remotes for keyless entry with a 200 pontiac grand am?


Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:

Sit in the vehicle driver's seat.
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation

Oct 21, 2009 | 2000 Pontiac Grand Am GT

1 Answer

Programming new keyless entry remote


Yes...

1) Remove the "MALL PGM" fuse located in the glove compartment (see owners manul for location)

2) Turn ignition switch to "Accessory" then "Off" then back to "Accessory" witin 1 second. (accessory is opposite the forward direction key is normally turned for starting the vehicle)

3) Plug in drivers side seat belt.

4) Open and close a door (will hear a chime indicating in program mode.)

5) Press and hold both the "Lock" and "Unlock" buttons on the Fob and wait at least 7 seconds (may take longer) you'll hear a chirp or the horn will sound.

6) repeat step 5 for all other Fobs.

7) turn key to Off and replace fuse.

Jun 13, 2008 | 1999 Pontiac Grand Prix

Not finding what you are looking for?
1999 Pontiac Grand Am GT Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...