Question about 1994 Pontiac Trans Sport

1 Answer

I NEED A DIAGRAM OF THE SPARK PLUG CONNECTED TO THE COIL

MY WIRES IS CROSS UP

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 17,970 Answers

Hi there:
1994 Pontiac Trans Sport 3.8 liter V-6 VIN "L"

I NEED A DIAGRAM OF THE SPARK PLUG CONNECTED TO TH - 10_27_2012_2_01_40_am.gif
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Oct 27, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: 2003 Ford Taurus spark plug diagram

Have a look here.

http://www.autozone.com/N,26200242/shopping/specsSelect.htm

Posted on Feb 02, 2009

fastboyz
  • 674 Answers

SOURCE: Diagram for spark plug wires

Firing order 1-6-5-4-3-2
------------
| 2 4 6 |
front | |
| ------- |
| | 6 5 ||
of | | 1 4 ||
| | 2 3 ||
| ------- |
vehicle | |
| 1 3 5 |
------------
Distributor rotates clockwise

Posted on Sep 15, 2008

landsend
  • 1066 Answers

SOURCE: spark plug wires

the firing order is stamped on the intake manifold.  next time replace them one at a time.

Posted on Mar 26, 2009

  • 462 Answers

SOURCE: need a diagram of the firing order of spark plug wires from coil packs to spark plugs

FROM LEFT TO RIGHT, 5/2 3/6 4/1. ASSUMING YOU HAVE THE 3.1L ENGINE.

Posted on May 31, 2009

  • 158 Answers

SOURCE: spark plug wiring diagram for gm 3.4 liter v6

http://autorepair.about.com/od/enginefiringorders1/Engine_Firing_Orders.htm

Posted on Aug 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 buick spark plug diagram


If the wires are in good condition, there is no harm in crossing them along their route. What kind of diagram do you need? What is the model and engine size?

Aug 05, 2017 | Buick Cars & Trucks

1 Answer

I replaced the coil plugs and wires and it is running ruff. I need a wiring diagram to make sure the wires are on the right spot on the coil.


if your car fires up, then the spark plug wires and coil wires are properly done. if it is running rough then you may have made one of several mistakes.

you may have needed to "gap" the arc end of the spark plugs (unless they were specifically "pre-gapped" for your particular make and model).

you may have not tightened one of the spark plugs all the way in, allowing too much air to enter the combustion chamber.

worst of all, you may have cross-threaded a spark plug, which would also allow too much air into the compustion chamber. it is usually possibe to re-thread the spark plug hole, using what i believe is called a "tap-and-die", but i have never done this before, so i am not sure if its success rate or difficulty level.

Mar 26, 2011 | Ford Taurus Cars & Trucks

1 Answer

Describe your how fix my pontiac 2000 montana Problem changing spark plugs



Inspection

Inspect for the correct routing of the spark plug wires. Improper routing may cause cross-firing. Inspect each wire for any signs of cranks or splits in the wire. Inspect each plug wire boot for tearing, piercing, arcing, carbon tracking or a corroded terminal.
If there is any corrosion, carbon tracking or arcing indicated on a plug wire boot or terminal, both the plug wire and component it was connected to should be replaced.


Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the left side spark plug wires from the spark plugs.
  3. Remove the left side plug wires from the retaining clips.
  4. Rotate the engine for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. Remove the right side spark plug wires from the spark plugs.
  6. Remove the plug wires from the retaining clip.
  7. Remove the spark wires from the ignition coils.
  8. Remove the plug wire assembly from the engine.
    NOTE If you are replacing the spark plug wires, the spark plug wire conduit and retaining clips should be transferred to the replacement wires.

To install:
  1. Install the right side plug wires to the ignition coils and then the spark plugs.
  2. Install the spark plug wires to the retaining clip.
  3. Rotate the engine back to the original position.
  4. Install the left side spark plug wires to the ignition coils and then to the spark plugs.
  5. Install the spark plug wires to the retaining clips.

3.9L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the intake manifold cover.
  3. Remove the left side spark plug wires as follows:
    1. Disconnect the left side spark plug wires from the spark plugs.
    2. Disconnect the left side spark plug wires from the ignition coil.
    3. Remove the left side spark plug wire clips from the intake manifold and heater inlet and outlet pipe.
    4. Remove the left side spark plug wire assembly.

  4. If removing the right side spark plug wires, the engine must be rotated for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. After rotating the engine, remove the right side spark plug wires as follows:
    1. Disconnect the right side spark plug wires from the spark plugs and ignition coil.

  6. Remove the right side spark plug wire clip from the ignition coil bracket.
  7. Remove the right side spark plug wire assembly.

To install:
  1. Install the spark plug wire assembly.
  2. Install the right side spark plug wire clip at the ignition coil bracket.
  3. Connect the plug wires to the ignition coil and spark plugs.
  4. If the engine was rotated for access, return the engine to the original position.
  5. The remainder of the installation is the reverse order of removal.

Feb 05, 2011 | 2000 Pontiac Montana

3 Answers

1999 ford escort I changed the plugs, but broke a plug cap. Bought a generic replacement spark plug wire that had to be modified to fit into the head. I cannot get the firing order correct. The car...


Remove the plugs from the head. Insert into the coil wires. Make sure they are properly earthed on the engine. Crank the motor and check for spark at each of the plugs.
Refer to the diagram. Cylinders are connected as shown on the diagram in blue. 1 goes to cylinder 1(sparkplug furthest from coil pack), 2 to 2, 3 to 3 and 4 to 4(closets to coil pack).
To test the coil pack use a digital volt meter. Measure resistance between coil towers for coil 1(marked 1 in red on diagram) Value should be between 12000 and 14500 ohm. Do the same for coil towers 2.
Measure resistance between I and C1. If the measurement is more than 5 ohm the coil is defective. Do the same for I to C2.
Measuring voltage at I(Ignition start/run) to ground should be 10V.
I is connected to the 15A engine fuse. The radio interference capacitor is connected between this line and earth at the coil. Disconnect it to see if it cures the problem.
C1 and C2 connect to the powertrain control module.
Bear in mind that aftermarket coil wires may cause problems with misfiring, so see if you cant find an OEM coil wire to replace the broken one before replacing anything else.

suzman_16.jpg

Nov 15, 2010 | 1989 Ford Escort

1 Answer

Putting plug wires on a 1997 ford explorer awd that has no wires need diagram for placement


You dont need diagram. If you will notice there is seperate coils for each spark plug. you need 9/32 socket to remove each coil. Theres a small screw that holds the coil in place, Remove the srew, remove the coil, once you remove the coil take a spark plug socket and extension to remove the plug.On the end of each coil is a boot that looks like the end of a spark plug wire . You can buy a set of those boots.Do these one at a time. You can gat a book a auto parts store that could help for about twenty bucks. Hope this helps Leave comment

Apr 07, 2010 | 1997 Ford Explorer AWD

1 Answer

Diagram of the motor


Don't need a diagram for that!

Just follow any of the spark plug wires, one end goes to the spark plug and the other to the coil.

Good Luck.

Mar 09, 2010 | 2005 Ford Freestar

1 Answer

Engine diagram for a 2000 toyota corolla


remove the spark plug wires one by one.. remember the connection from no. 1 spark plug to the distributor. the wire from the coil is connected to the center of the distributor.

Sep 17, 2009 | 2000 Toyota Corolla

1 Answer

Need a diagram of the firing order of spark plug wires from coil packs to spark plugs


FROM LEFT TO RIGHT, 5/2 3/6 4/1. ASSUMING YOU HAVE THE 3.1L ENGINE.

May 31, 2009 | 1998 Chevrolet Lumina

3 Answers

Coil pack. what and where is it? what does it look like?



 
 
Ignition Coil
Removal & Installation
4.2L Engine
1997-2000
To Remove:

Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The radio ignition interference capacitor connector
The locking tabs
The six ignition wires, marking for reinstallation
The brackets
The spark plug wire set
CAUTION
Spark plug wires must be connected to the proper ignition coil terminal. Mark spark plug wire locations before removing them.
The accelerator cable bracket nut
The accelerator cable bracket bolt
The accelerator cable bracket and position it aside.
The two ignition coil nuts
The ignition coil stud bolt
The ignition coil
To Install:
Install or connect the following:
The ignition coil
The two ignition coil nuts
The ignition coil stud bolt
Torque to: 71-98 inch-lbs (8-11 Nm)
The accelerator cable bracket
The accelerator cable bracket nut
The accelerator cable bracket bolt
Torque to: 71-98 inch-lbs (8-11 Nm)
The ignition coil electrical connector
The radio capacitor connector


CAUTION
The Spark plug wires must be connected to the proper ignition coil terminal.
Squeeze the locking tabs and connect the six ignition cables.
2001-2003
To Remove:

Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The spark plug wires, marking for reinstallation
CAUTION
The sparkplug wires must be connected to their correct ignition coil terminal.
The ignition coil
The bolts
Inspect the ignition coil for carbon tracks or damage.
To Install:
Inspect the ignition coil for carbon tracks or damage.
Install or connect the following:
The ignition coil
The bolts
Torque to: 53 inch-lbs (6 Nm)
The ignition coil electrical connector
The spark plug wires, in their original positions
4.6L Engine
1997-1999
To Remove:

NOTE: This procedure is for either RH or LH ignition coil.
Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The radio capacitor electrical connector
The spark plug wires by squeezing the locking tabs (four each side)
CAUTION
The spark plug wires must be connected to their proper ignition coil terminal. Mark spark plug wire locations.
The bolts
The ignition coil
To Install:
NOTE: The procedure is for either LH or RH ignition coil
Install or connect the following:
The ignition coil
The bolts
Torque to: 44-62 inch-lbs (5-7 Nm)
The ignition coil electrical connector
The radio capacitor electrical connector
The spark plug wires (four each side), into their original positions by squeezing the tabs


CAUTION
The spark plug wires must be connected to their proper ignition coil terminal.

 
Top of Form 1
Bottom of Form 1

Mar 28, 2009 | 1998 Ford F150 Regular Cab

1 Answer

Replacing spark plug wires on 1995 Buick Riviera


You need to drain some coolant. Loosen and disconnect water lines by the firewall- the ones in the way of your wire change. u need to get a diagram of the firing order of the engine so that those wires are correctly connected to the coil packs.

Mar 21, 2009 | 1995 Buick Riviera

Not finding what you are looking for?
1994 Pontiac Trans Sport Logo

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8547 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...