Question about 2006 Ford Mustang

1 Answer

I have codes 0122 0123 2104 2110 2111 2112 would it be the throttle body

It appears someone change the alternator and thermostat housing

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,398 Answers

Trouble Code: P0122

Throttle/Pedal Position Sensor A Circuit Low

Possible Causes:


Open ETC TP sensor harness.Short to ground in the ETC TP sensor harness.Damaged TP sensor.SIG RTN circuit open to the TP sensorPCM has failed


Trouble Code: P0123

Throttle/Pedal Position Sensor A Circuit High

Possible Causes:


TP sensor not seated correctly.TP sensor harness is short to voltage.TP sensor harness short to VREF.SIG RTN circuit open to the TP sensor.Damaged TP sensor.PCM has failed.Trouble Code: P2104

Throttle Actuator Control (TAC) System (Forced Idle)

Possible Causes:


Air cleaner and air inlet are not correctly seated.Check for self-test DTCs in all of the vehicle modules.Accelerator Pedal Position (APP) sensor.Throttle Position (TP) sensor.Manifold Absolute Pressure (MAP) sensor.PCM has failed.

Mustang 2006-2008
4.0L V6 VIN N Auto 12

Print


Trouble Code: P2008

Intake Manifold Runner Control (IMRC) Circuit Open (Bank 1)

Possible Causes:


IMRC monitor circuit open


Trouble Code: P2014

Intake Manifold Runner Position Sensor/Switch Circuit (Bank 1)

Possible Causes:


IMRC monitor circuit openMechanical concern - bind, seize, damage or obstruction of IMRC hardware


Trouble Code: P2015

Intake Manifold Runner Position Sensor/Switch Circuit Range/Performance (Bank 1)

Possible Causes:


Mechanical concern - bind, seize, damage, or obstruction of IMRC hardware


Trouble Code: P2019

Intake Manifold Runner Position Sensor/Switch Circuit (Bank 2)

Possible Causes:


IMRC monitor circuit openMechanical concern - bind, seize, damage, or obstruction of IMRC hardware


Trouble Code: P2020

Intake Manifold Runner Position Sensor/Switch Circuit Range/Performance (Bank 2)

Possible Causes:


Mechanical concern - bind, seize, damage, or obstruction of IMRC hardware


Trouble Code: P2065

Fuel Level Sensor B Circuit

Possible Causes:


Communication link concernDamaged Instrument Panel Cluster (IPC) (MKS)Damaged Instrument Cluster (IC)Damaged PCM


Trouble Code: P2066

Fuel Level Sensor B Circuit Range/Performance

Possible Causes:


Communication link concernDamaged Instrument Panel Cluster (IPC) (MKS)Damaged Instrument Cluster (IC)Damaged PCM


Trouble Code: P2067

Fuel Level Sensor B Circuit Low

Possible Causes:


Communication link concernDamaged Instrument Panel Cluster (IPC) (MKS)Damaged Instrument Cluster (IC)Damaged PCM


Trouble Code: P2068

Fuel Level Sensor B Circuit High

Possible Causes:


Communication link concernDamaged Instrument Panel Cluster (IPC) (MKS)Damaged Instrument Cluster (IC)Damaged PCM


Trouble Code: P2070

Intake Manifold Tuning Valve (IMTV) Stuck Open (Bank 1)

Possible Causes:


IMTV signal circuit shorted to PWR GND or SIG RTNDamaged IMRC actuatorPCM has failed


Trouble Code: P2071

Intake Manifold Tuning Valve (IMTV) Stuck Closed Bank 1

Possible Causes:


IMTV signal circuit shorted to PWR GND or SIG RTNDamaged IMRC actuatorIMTV circuit openPCM has failed


Trouble Code: P2072

Throttle Actuator Control (TAC) System (Ice Breakage)

Possible Causes:


Ice or oil in the intake air system could be the result of a Positive Crankcase Ventilation (PCV) system concern


Trouble Code: P2096

Post Catalyst Fuel Trim System Too Lean (Bank 1)

Possible Causes:


Loose connection, and damaged or corroded terminalsExhaust leaksContaminated HO2S


Trouble Code: P2097

Post Catalyst Fuel Trim System Too Rich (Bank 1)

Possible Causes:


Loose connection, and damaged or corroded terminalsExhaust leaksContaminated HO2S


Trouble Code: P2098

Post Catalyst Fuel Trim System Too Lean (Bank 2)

Possible Causes:


Loose connection, and damaged or corroded terminalsExhaust leaksContaminated HO2S


Trouble Code: P2099

Post Catalyst Fuel Trim System Too Rich (Bank 2)

Possible Causes:


Loose connection, and damaged or corroded terminalsExhaust leaksContaminated HO2S


Trouble Code: P2100

Throttle Actuator Control (TAC) Motor Circuit/Open

Possible Causes:


TAC motor has an open windingTAC motor is damagedTAC motor harness is openTAC motor harness is short to PWRTAC motor harness circuits are short togetherTAC motor harness connector is unplugged


Trouble Code: P2101

Throttle Actuator Control (TAC) Motor Range/Performance

Possible Causes:


TAC motor circuits are cross-wired


Trouble Code: P2104

Throttle Actuator Control (TAC) System (Forced Idle)

Possible Causes:


Air cleaner and air inlet are not correctly seatedCheck for self-test DTCs in all of the vehicle modules.Accelerator Pedal Position (APP) sensorThrottle Position (TP) sensorManifold Absolute Pressure (MAP) sensorPCM has failed


Trouble Code: P2105

Throttle Actuator Control (TAC) System (Forced Engine Shutdown)

Possible Causes:


Air cleaner and air inlet are not correctly seated.Check for self-test DTCs in all of the vehicle modules.Accelerator Pedal Position (APP) sensor.Throttle Position (TP) sensor.Manifold Absolute Pressure (MAP) sensor.PCM has failed.


Trouble Code: P2107

Throttle Actuator Control (TAC) Module Processor

Possible Causes:


TAC motor harness circuit short to ground.TAC motor harness circuit short to voltage.Damaged Electronic Throttle Body (ETB).PCM has failed.


Trouble Code: P2110

Throttle Actuator Control (TAC) System (Forced Limited RPM)

Possible Causes:


Air cleaner and air inlet are not correctly seated.Check for self-test DTCs in all of the vehicle modules.Accelerator Pedal Position (APP) sensor.Throttle Position (TP) sensor.Manifold Absolute Pressure (MAP) sensor.PCM has failed.


Trouble Code: P2111

Throttle Actuator Control (TAC) System (Stuck Open)

Possible Causes:


Binding throttle body, stuck open.TAC motor circuit open.TAC motor circuits are cross-wired.TAC motor harness circuits are shorted together.PCM has failed.


Trouble Code: P2112

Throttle Actuator Control (TAC) System - Stuck Closed

Possible Causes:


Binding throttle body, stuck open.TAC motor circuit open.TAC motor circuits are cross-wired.TAC motor harness circuits are shorted together.PCM has failed.

Posted on Oct 26, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Where is thermostat located 4.3 liter chevy s10, 2003


The thermostat is located inside the steel thermostat housing, which is located on the front of the engine right in front of the throttle body housing and halfway between the alternator and a/c compressor. Remove the air intake assembly and remove the front bracket connected to the front two bolts of the throttle body. Then remove the two main bolts of the thermo housing. Lift up the thermo housing and you will see the thermostat sitting there.
25887031-4lgilslwfm41o0t5ittchrga-2-0.jpg

Sep 30, 2015 | Cars & Trucks

1 Answer

Removing thermostat housing


my son is electrical engineer,he can answer

Feb 27, 2014 | Oldsmobile Cars & Trucks

1 Answer

Engine diagram 1997 buick skylark/thermostat


follow the water inlet pipe to water pump the thermostat housing connects to water pump this is for 2.4l engine you have to remove exhaust manifold heat shield.you will see the water inlet pipe going to water pump inlet thermostat housing.for the 3.1 engine follow top radiator hose to thermostat housing you have to remove air filter air duct and filter housing , you have to remove throttle body unit with coolant hoses, you have to disconnect accelerator cable, transmission down shift cables at the bracket bolts to throttle body.once you remove throttle body unit then you can see and remove the thermostat housing to replace thermostat.you need to buy new throttle body gasket,and new small coolant hoses connects to the throttle body unit.have extra gallon antifreeze dexcool on hand.

Nov 15, 2011 | Cars & Trucks

1 Answer

Change thermostat on 2004 chevy impala?


first you need drain engine coolant down below thermostat. what engine type 3.8 or 3.4 need to know.the 3.8 engine thermostat housing on top intake follow top radiator hose to thermostat housing.the 3.4 engine you have to remove air filter housing with air inlet duct with mass air flow sensor.you have to remove throttle body with coolant hoses.go to auto parts store buy new throttle body hoses old ones will be hard to remove might have to cut two small hoses also buy new throttle body gasket also. before you can remove throttle body unit you have to remove accelerator cable and downshift cable from bracket bolted to throttle body.once throttle body remove then you can remove thermostat housing bolt remove replace thermostat.

Nov 11, 2011 | 2004 Chevrolet Impala

1 Answer

How do i change the themostat on a 1998 olds silouhette


the thermostat is under the throttle body
1 remove the air inlet tube from the throttle body to air box
2 drain the coolant
3 remove the throotle body
4 the top bolt is easy remove 13mm bolt from thermostat housing
5 the bottom bolt not so easy remove 3/4 of the way out bottom hole on housing is slotted
6 remove thermostat housing
7 replace thermostat and reassemble
hope this helps

Nov 11, 2009 | 1998 Oldsmobile Silhouette

2 Answers

Where is the thermostat housing on a 1006 Buick Regal?


The thermostat in the 3.1 engine is in the thermostat housing. Follow the upper radiator hose towards the engine, where the hose connects to the engine is the thermostat housing which leads under the throttle body. Yup, it's not the easiest thing to get to unless you have small hands and a few socketextensions and swivel. If you have small hands you can remove the thermostat housing without removing the throttle body. Just remove cross over exhaust heat shield to give you enough room to get the socket with an extension and swivel to the two bolts to the thermostat housing under the throttle body. Remove front bolt and the second one just needs to be loosen and you can wiggle out the thermostat housing to replace the thermostat. If you need more room, your going to have to remove the throttle body and replace the throttle body gasket also to give you more room to get the thermostat housing out. Good luck and hope this helps and take care not to damage the temperature sensor on the manifold just in front of the housing. Keep me posted if you have any more questions and take your time.  

Jul 15, 2009 | 1996 Buick Regal Olympic Gold

2 Answers

Where is the thermostat


The thermostat in the 3.1 engine is in the thermostat housing. Follow the upper radiator hose towards the engine, where the hose connects to the engine is the thermostat housing which leads under the throttle body. Yup, it's not the easiest thing to get to unless you have small hands and a few socket extensions and swivel. If you have small hands you can remove the thermostat housing without removing the throttle body. Just remove cross over exhaust heat shield to give you enough room to get the socket with an extension and swivel to the two bolts to the thermostat housing under the throttle body. Remove front bolt and the second one just needs to be loosen and you can wiggle out the thermostat housing to replace the thermostat. If you need more room, your going to have to remove the throttle body and replace the throttle body gasket also to give you more room to get the thermostat housing out. Good luck and hope this helps and take care not to damage the temperature sensor on the manifold just in front of the housing. Keep me posted if you have any more questions and take your time. 

Jul 15, 2009 | 1997 Oldsmobile Cutlass Supreme

1 Answer

Change thermostat on gm 3400 v6


Drain coolant at the radiator drain. Remove air intake hose and MAF sensor assembly. remove throttle cable bracket and disconnect cable linkage. Remove throttle body bolts and disconnect coolant hoses to throttle body. Loosen heater hose pipe and remove heater hose from rear of pipe. Remove radiator hose from thermostat housing. Remove top thermostat housing bolt. Loosen and almost remove lower thermostat bolt. You will need to slide your wrench and hand under the exhaust crossover pipe to gain access. Loosen the bolt until you can remove the thermostat housing, it should be slotted to clear the bolt. Replace the thermostat and reassemble. Bleed cooling system using the two bleed screws (one on thermostat housing and the other on the passenger side of the engine where the heater hose pipe comes out above the water pump.

Jan 23, 2009 | 2003 Pontiac Montana

1 Answer

Engine wants to stall


You need to Clean the throttle body bore and the throttle valve plate using a clean shop towel and some carb cleaner. The DTC P0128 is Engine Coolant below the minimum thermostat regulating temperature. You need to replace the thermostat, it comes as an outlet housing assembly. You will have to remove the alternator to gain access to this housing.

Jul 20, 2008 | 2003 Chevrolet TrailBlazer

Not finding what you are looking for?
2006 Ford Mustang Logo

661 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5623 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...