Question about 2005 Dodge Magnum

1 Answer

Need an exploded view of door latch assembly for front driver door 2005 Dodge Magnum. Cant find where rod connects to latch...

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 14,362 Answers

Remove other side to see.

Posted on Oct 26, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 2005 Dodge Magnum w/out hemi stalling

I have a 2005 Magnum and was also having this problem. Stalled out a few times and continued to idle rough and feel like it was going to die when I would slow down. At times it would feel like I would get a hesitation and then a surge. Engine light would go on for a day or so, then go out for a few days. First time I took it in, the dealership told me that it was a broken seal (I don't know where), but they replaced it and it continued to happen. The second time I took it to a mom & pop shop, and they told me that it was the oxygen sensor/altimeter, replaced it (only a $35 part), and I haven't had a problem since. That was 6 months ago. Hope this helps...

Posted on Sep 30, 2008

BCally1
  • 133 Answers

SOURCE: How do I change a EGR Valve on a 2005 Dodge Magnum STX w/3.5 engi

its a pain in the *** but it located on the right rear (pass. side) of the motor. it bolts to the cylinder head and runs up to the intake manifold

Posted on Jan 09, 2009

  • 70 Answers

SOURCE: 2005 Dodge Magnum, after replacing battery,cd player won't work

My story Dealing with Dodge

I had a 1994 Dodge Ram. The Red Dodge Ram I had it malfunctioned and my brake became the throttle. I had to put the truck in reverse then park. to stop, after it was out of control at 80 mph a hill slowed us down. Are you sure its not electrical and the curse control is not giving you trouble? Mine had multifunction switch was not working and the headlight switch burned up. I also found out that Audi had problem with the brake becoming the throttle in the 1980s Daimler Chrysler and Audi were German made. I don't think there is an easy answer. I hope you stay safe. Another man is having strange trouble also. I'm sure there are many more people with trouble with the vehicles. I wish Dodge would step up to the truth. and recall their nightmares. I saw many of their 1996 Dodge trucks at their dealers shop with all the electrical pulled out.

Posted on Mar 22, 2009

Murphybanton
  • 2004 Answers

SOURCE: unable to locate the fuel filter on my 2005 dodge magnum 2.7 liter

It's located in your fuel tank.

cheers.

Posted on May 21, 2009

  • 149 Answers

SOURCE: I need the torque specs for the connecting rod cap

Step #1 40lbs PLUS Step#2 1/4 turn 90 degrees.....this is for 3.3 & 3.8

Posted on Jan 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a magnum 05 and I have cold air coming out of the driver side and hot air coming out the passenger side, I changed all three blend doors and no charge


There is a bad blend door motor or controller/wiring problem. Worst case scenerio is a bad blend door within the HVAC assembly

May 31, 2015 | 2005 Dodge Magnum

1 Answer

How do i take off the inside drivers door panel on a 2005 dodge caravan


Hi Roberta, here's the instructions on how to remove your door panel. I have to wonder though on why you are removing it, my guess is you window doesn't roll up or down and your replacing the regulator. Any way here goes.

REMOVAL

  1. Remove the plug and remove screw attaching door pull cup to inner door panel.
  2. Remove switch bezel and disconnect power window/memory switch.
  3. Remove screws attaching trim panel to door from below map pocket.
  4. If equipped, remove window crank. (Refer to 23 - BODY/DOOR - FRONT/WINDOW CRANK - REMOVAL)
  5. Remove screw holding door trim to door panel from behind inside latch release handle .
  6. Disengage clips attaching door trim to door frame around perimeter of panel.
  7. Lift trim panel upward to disengage flange from inner belt molding at top of door.
  8. Tilt top of trim panel away from door to gain access to latch linkage.
  9. Disengage clip attaching linkage rod to inside latch release handle (INSIDE DOOR HANDLE LINKAGE).
  10. Separate linkage rod from latch handle.
  11. Disconnect the power door switch, courtesy lamp electrical connectors.
  12. Remove front door trim panel from vehicle.
Hope this helps and have an awesome day Roberta!

May 21, 2014 | 2005 Dodge Grand Caravan

1 Answer

I have a 1997 F-250 HD. Driver door latch cable is broken at the handle end. I have a replacement cable, but need help figuring out how to remove the broken cable without breaking the plastic rod...


Door Handle/Latch Assembly NOTE: Due to the conversion from single 90-degree rod end shape to double 90-degree rod end shape, it may be necessary to remove more parts than the instructions indicate. This action will allow more maneuverability of the rod and ease the removal process.
Handle, Outside Door, Front Removal
  1. Remove the front door trim panel (23942) and front door trim shield (237A04) from the front door (20124). Refer to Section 01-05 .
  1. Disconnect the front door latch actuating rod (22152) from the handle link connector.
  1. Remove one nut and screw.
  1. Remove handle and pads from door.
----------------------
Some rods are double 90 degree rods, they require the handle or lach to be free when the rod is attached.
Some have plastic clips that slide onto the rod. they pop off sideways.

May 06, 2011 | Ford F-250 Cars & Trucks

1 Answer

Rear door latch on the inside of door is off . where does it connect???? 2005 chevy truck suicide door drivers side


remove door panel follow the rods back to the latch or if its the front that attaches to the handle remove handle will reattch on back of handle

Feb 09, 2011 | 2005 Chevrolet Silverado

1 Answer

How do you replace the regulator for the power window on the 2002 ford explorer


Regulator - Power Windows - Front Door
  1. Remove the front door trim panel as follows:
    1. Remove the front door handle bezel.
    2. Remove the front door window/lock control switch bezel.
    3. Disconnect the window/lock control switch electrical connectors.
    4. Remove the 3 front door trim panel screws.
      CAUTION To avoid damaging the trim panel, do not pull directly outward to carry out this step.
    5. Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
    6. Remove the exterior mirror control switch from the front door trim panel.
  2. Remove the front door speaker.
  3. Remove the interior molding.
  4. Disconnect the door lock actuating rod at the door handle assembly:
    1. Release the door lock actuating rod clip.
    2. Position the door lock actuating rod aside.
  5. Remove the front door weather shield.
    CAUTION Make sure the holes in the glass bracket do not become enlarged during the rivet removal process. If the holes become enlarged, the new rivets may become loose, resulting in clicking noise concern.
    NOTE Some vehicles may use rivets to attach the window glass to the window regulator assembly. Use a 4.5 mm (0.1772 in) drill bit to drill out the glass-to-regulator rivets.
  6. Remove the 2 front door window glass-to-regulator bolts or rivets.
  7. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets.
  8. Secure the front door glass in the full up position with tape.
  9. Disconnect the window regulator motor electrical connector.
  10. Remove the 4 window regulator assembly nuts.
  11. Remove the window regulator assembly.

    0b00886.jpg

    Fig. Exploded view of the front door and power window components-2005 Explorer and Mountaineer

To install:
  1. Position the window regulator assembly.
  2. Install the 4 window regulator assembly nuts. Tighten to 89 inch lbs. (10 Nm).
  3. Connect the window regulator motor electrical connector.
  4. Remove the tape securing the front door glass in the full up position.
  5. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets. Install the bolt and tighten the bolts to 62 inch lbs. (7 Nm), or install new rivets.
  6. Install the front door weather shield.
  7. Connect the door lock actuating rod at the door handle assembly:
    1. Position the door lock actuating rod into proper location.
    2. Attach the door lock actuating rod clip.
  8. Install the interior molding.
  9. Install the front door speaker.
  10. Install the front door trim panel as follows:
    1. Install the exterior mirror control switch from the front door trim panel.
    2. Position the door trim panel onto the armrest to engage the panel clips.
    3. Install the 3 front door trim panel screws.
    4. Connect the window/lock control switch electrical connectors.
    5. Install the front door window/lock control switch bezel.
    6. Install the front door handle bezel.

  1. Raise the front door window glass to the full up position.
  2. Remove the interior door handle.
  3. Support the front door window glass.
  4. Disconnect the front door window regulator motor electrical connector.
  5. Remove the equalizer bracket nuts.

    4945f24.jpg
    Fig. Remove the equalizer bracket nuts-2005 Explorer Sport-Trac
  6. Remove the front door window regulator by removing the rivets and nuts.
  7. Remove the front door window regulator motor retaining bolts and then remove the motor.

    52a6816.jpg

    Fig. Remove the front door window regulator motor retaining bolts and then remove the motor-2005 Explorer Sport-Trac
To install:
  1. Installation is the reverse of the removal procedure.
  2. Tighten the regulator motor mounting bolts to 8 ft. lbs. (11 Nm).

Hope this help (remember rated and comment this).

Mar 24, 2010 | 2002 Ford Explorer

1 Answer

Cant get the rear bench in


The front bottom connections goes in first. You have to lift the back of the bench up and slide the u-shaped connections under the rods. Once there in, then lower the back of the bench. The back has latches that should spring open and around the rods in the floor opening. You should be able to actually drop the back of the bench and they should "seat", however it is better to place the back of the bench on top of the rods, and using the lever located on the bottom of the bench - open the latches; causing the latches to grab the rod.
Let me know if this helped, or if you have any additional information, problems, or questions. Feel free to contact me at FixYa.com!

Jan 25, 2010 | 2005 Dodge Grand Caravan

1 Answer

Sliding door problem


You probably have a burnt out door lock soleniod, it's part of the latch, stuck in the locked position, you have to pry the latch from the inside, to release the catch, just replace the latch when done. GOOD LUCK, RDJRP

Oct 02, 2009 | 2005 Dodge Caravan

1 Answer

Trying to remove door latch on 1995 thunderbird. Car has power locks.


inside or outside latch? please rate

Section 01-14A: Handles, Locks, Latches and Mechanisms 1995 Thunderbird, Cougar Workshop Manual
REMOVAL AND INSTALLATION Latch, Door Removal and Installation
  1. Remove front door trim panel (23942) and watershield from front door (20124). Refer to Section 01-05 .
  1. Mark the location of the bolt retaining front door glass run front retainer (21572). Remove the bolt.
  1. Check all rod connections against the appropriate illustration. Correct any disconnected or loose connections and check operation before replacing parts.
  1. Remove power door lock actuator (218A42).
  1. Disconnect the rods from the front door latch (21812) . The front door latch remote control link (21940) and the latch-to-lock cylinder rod cannot be removed because of the rod's end configuration. Remove wiring from clip on front door latch shield.
  1. Remove front door latch control cylinder rod (22134) from the door lock cylinder (21985).
  1. Remove front door latch remote control and link (21818).
  1. Remove the front door latch retaining screws. Disconnect the door open warning lamp switch (14018) , if so equipped. Remove the front door latch from the front door .
  1. NOTE: Do not damage anti-theft shield.
    Remove anti-theft shield from the front door latch .
  1. Remove front door latch remote control link , front door latch control cylinder rods , and door open warning lamp switches from front door latch , where applicable.
  1. To install, reverse Removal procedure. Tighten front door latch retaining screws 4-8 Nm (36-70 lb-in).
3e933ef.gif

Item Part Number Description 1 21852 Front Door Latch Push Button Rod 2 21940 Front Door Latch Remote Control Link 3 386656-S Bushing 4 21978 Door Latch Shield 5 218A42 Power Door Lock Actuator 6 22134 Front Door Latch Control Cylinder Rod 7 21812 Front Door Latch
------------------------------------------------------------------------------------
Remote Control Assembly Door Latch
Removal and Installation
  1. Remove front door trim panel (23942) and watershield. Refer to Section 01-05 .
  1. Remove screw and washer assembly retaining front door latch remote control and link (21818) to front door (20124) .
  1. Rotate front door latch remote control and link to remove from front door latch remote control link (21940) .
  1. To install, reverse Removal procedure.

Sep 27, 2009 | 1995 Ford Thunderbird

1 Answer

2000 dodge dakota door panel


There are five screws to be removed, two of which are Torx bit. One is in the center of the door panel towards the top. One is behind the door latch handle. One adjacent to the side view mirror, and two along the bottom. There is an access panel along side the door latch handle you need to pop off with a screw driver. It is triangular in shape and about 5 inches long. Once that is removed you will see the door latch linkage to latch handle. Disconnect the linkage by unsnapping the plastic retainer off of the linkag rod and swing it so the rod can be lifted out of the hole. The window crank handle is a *****, you will need a dentist's pick or similar to remove a retaining clip just behind the handle but in front of the panel. The it is just an upward and outward movement on the panel and it should come right out.

Feb 28, 2009 | 1999 Dodge Dakota

Not finding what you are looking for?
2005 Dodge Magnum Logo

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...