Frod Fusion broken antenna

Question edited for clarity.
Question moved to Model Category.

Video in the link Bridgett

https://www.google.com/search?q=Location+of+purge+valve+on+2008+Ford+Fusion+SE

..

Locate the pipes and check if they are rubber hoses or metal pipes,tool needed will probably be pipe spanners.

2.3L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009

1. Raise and safely support the vehicle.
2. Drain the cooling system.
3. Loosen the 3 coolant pump pulley bolts.
4. Remove the accessory drive belt.
5. Remove the 3 bolts and the coolant pump pulley.
   1. To install, tighten to 15 ft. lbs. (20 Nm).
6. Remove the 3 bolts and the coolant pump.
7. Remove and discard the O-ring seal.
   1. To install, tighten to 89 inch lbs. (10 Nm).
   
   

Fig. Exploded view of the water pump-2.3L engine


To install:

1. To install, reverse the removal procedure.
2. Lubricate the O-ring seal with clean engine coolant.
3. Fill and bleed the cooling system

3.0L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009

1. Raise and safely support the vehicle.
2. Drain the cooling system.
3. Remove the coolant pump belt.
4. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley.

Fig. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley

5, Disconnect the heater hose from the coolant pump.
6. Disconnect the coolant pump-to-engine hose and position aside.
7. Remove the 3 bolts from the coolant pump assembly.
8. Reposition the coolant pump-to-thermostat housing hose clamp and remove the coolant pump and hose as an assembly.



Fig. View of the water pump and related components-3.0L engine

To install:

1. Connect the coolant pump-to-thermostat housing hose and reposition the clamp.
2. Position the coolant pump assembly and install the 3 bolts:
   1. Tighten to 89 inch lbs. (10 Nm).
   2. Tighten the 3 bolts an additional 90 degrees.
3. Connect the coolant pump-to-engine hose and the heater hose.
   NOTE
   Install the coolant pump drive pulley flush with the end of the camshaft.
4. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley.

Fig. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley

5. Install the coolant pump belt.
6. Fill and bleed the cooling system.

For the 4 cylinder, yes. For the 3.0 V6, it's on the firewall side (O2 banks are designated based on where cylinder no.1 is located).

how do you take centre console off for ford fusion because audio jack broken

2008 Ford Fusion Car Stereo Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Blue/Red
Car Radio Accessory Switched 12v+ Wire: Green
Car Radio Ground Wire: Black/Blue
Car Stereo Antenna Trigger Wire: Purple/Black
Left Front Speaker Positive Wire (+): White
Left Front Speaker Negative Wire (-): White/Brown
Right Front Speaker Positive Wire (+): White/Purple
Right Front Speaker Negative Wire (-): White/Orange
Left Rear Speaker Positive Wire (+): Brown/Green
Left Rear Speaker Negative Wire (-): Brown/Yellow
Right Rear Speaker Positive Wire (+): Brown/White
Right Rear Speaker Negative Wire (-): Brown/Blue

There should be a ring with a couple of notches in it at the base of where the antenna use to be. This ring is essentially a nut and is threaded and can be easily removed giving you better access to the broken antenna. I'm assuming that you are referring to a power antenna also.

On this website, you find fuse box diagram and description for Ford Fusion (2008)

http://www.autogenius.info/ford-fusion-2008-fuse-box-diagram-india-version

This link is from the handle to the latch. The door panel has to be removed in order for this problem to be fixed. The linkage is inside the door panel, it is a small diamater metal rod called a link. If you do the job yourself be careful not to break the door panel. In a shop, the labor is 1 hour for the job & if any, parts will be a seperate charge.