Question about 2002 Chevrolet Silverado 1500

1 Answer

How to remove front wheel bearing hub 2002 silverado

All the bolts are out but I'm having trouble removing the unit. Does anyone know a trick to get it loose?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,338 Answers

Use a 3 way puller.

Posted on Oct 26, 2012

  • Delbert Carter
    Delbert Carter Oct 27, 2012

    Thanks, but I have tried that. The splined shaft is loose, so there is nothing there for support. I'm going to get a slide hammer to attach to the studs and hope that pops it loose.

×

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 333 Answers

SOURCE: Replacing front wheel hub assembly on 2006

Caliper mount bolts are 74 ft/lbs
Driveshaft axle nut is 177 ft/lbs
Hub and bearing mounting bolts are 133 ft/lbs

Posted on Sep 10, 2009

Testimonial: "The info on the torgue specs was very helpful. I couldn't find it anywhere. Thanks a bunch!"

MNfisherman
  • 11896 Answers

SOURCE: 2004 silverado 4x4 2500 left front wheel bearing

  1. Raise and support the vehicle.
  2. Remove or disconnect the following:

    Tire and wheel assembly Caliper and rotor Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle Electrical connection for the wheel speed sensor Front drive halfshaft assembly on four wheel drive models Hub and bearing assembly mounting bolts Hub and bearing assembly O-ring seal from the steering knuckle bore (2500 series)
  3. Clean and inspect the O-ring seal
To install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly.
  2. Install the O-ring to the steering knuckle (2500 series).
  3. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent.
  4. Install or connect the following:

    Hub and bearing assembly Hub and bearing assembly mounting bolts. Tighten the bolts to 133 ft. lbs. (180 Nm). Front drive halfshaft assembly on four wheel drive models Electrical connection for the wheel speed sensor Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle. Tighten to 106 inch lbs. (12 Nm). Rotor Tire and wheel assembly.
You can go to autozone.com and register for free online repair manual with everything you need.

Posted on Jan 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

Front wheel bearing replace 4x4


It's pretty simple. -Remove the tire -Install a punch into the fins of the rotor. Rotate the rotor counterclockwise until the punch hits the caliper and remove the axle nut. - I like to remove the outer tie rod end from the knuckle. This makes it easier to get at the caliper bracket bolts and the wheel hub bolts - remove the caliper and the rotor - unplug the abs harness - remove the three bolts that hold the hub to the knuckle. - remove the hub/bearing from the knuckle. The hub may be corroded and frozen a little to the knuckle. Sometimes it can take a bit of hammering to get them to pop. Also make sure you torque the axle nut to the correct torque spec. Failure to do this will causing the bearing to fail early! Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Feb 25, 2012 | 1999 Chevrolet Silverado 1500

1 Answer

Replace left front wheel bearing on 2002 yukon 4x4 abs


Remove the axle nut. Put a punch in the fins of the rotor to keep the hub from spinning. Remove the caliper and the rotor. Unplu the abs harness. Remove the three bolts that hold the hub to the knuckle. Remove the hub/bearing from the knuckle. Reverse to install. Make sure you torque the three bolts that hold the bearing to the knuckle and the axle nut to the correct torques spec. Failure to do so will cause premature bearing failure. Also use a good quality bearing. SKF is a good brand. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Feb 02, 2012 | GMC Yukon XL Cars & Trucks

2 Answers

Front wheel bearing on 2 wheel drive replacement


It's a hub style bearing assembly bolted to the steering knuckle. After you have the wheel removed, remove the brake caliper and the brake rotor. Disconnect the Wheel Speed sensor connector under the rubber inner wheel well on the top of the frame. Nice part of the two wheel drive the bolts in behind the steering knuckle are easily accessable. After the hub is unbolted, it may take some hammering to remove the hub assembly from the knuckle. they do seize in at times. After the old hub is out, clean as much of the corrosion out of the knuckle cavity and maybe a light film of antiseize to make the next time easier. Reverse the procedure for assembling.
This is simplified. Have any more questions, just drop me a line.
Good luck

Aug 05, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

2008 siverado. Front-end humming. Sounds like extremely loud tire pattern noise coming from left-front wheel area, noise stops when i turn the steering wheel to the right. replaced tire with no results.


it is your wheel bearing. the bearing is a sealed unit so you replace the hub assembly. remove wheel,caliper,brake rotor.if it is 4x4 loosen axle nut. there are three 15mm bolts on back side of spindle remove these and slide hub out replace with new one. most hubs come with new wheel speed sensor so remove harness from connectors or if no new one remove the screw holding it in place to hub and slide out.

Dec 31, 2010 | 2008 Chevrolet Silverado 1500

1 Answer

REMOVAL OF FRONT WHEEL BEARINGS


Front (4 Wheel Drive) To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Tire and wheel assembly
    • Rotor (See: Disc Brake Rotor)
    • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
    • Electrical connection for the wheel speed sensor
    • Front drive halfshaft assembly (See: Halfshaft)
    • Hub and bearing assembly mounting bolts 4WD front hub 9308kg35.gif

    • Hub and bearing assembly
To Install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
  2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
  3. Install or connect the following:
    • Hub and bearing assembly
    • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
    • Front drive halfshaft assembly (See: Halfshaft)
    • Electrical connection for the wheel speed sensor
    • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
    • Rotor (See: Disc Brake Rotor
    • Tire and wheel assembly
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  4. Torque the lug nuts to specification
  5. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 03, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

2004 silverado 4x4 2500 left front wheel bearing


  1. Raise and support the vehicle.
  2. Remove or disconnect the following:

    Tire and wheel assembly Caliper and rotor Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle Electrical connection for the wheel speed sensor Front drive halfshaft assembly on four wheel drive models Hub and bearing assembly mounting bolts Hub and bearing assembly O-ring seal from the steering knuckle bore (2500 series)
  3. Clean and inspect the O-ring seal
To install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly.
  2. Install the O-ring to the steering knuckle (2500 series).
  3. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent.
  4. Install or connect the following:

    Hub and bearing assembly Hub and bearing assembly mounting bolts. Tighten the bolts to 133 ft. lbs. (180 Nm). Front drive halfshaft assembly on four wheel drive models Electrical connection for the wheel speed sensor Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle. Tighten to 106 inch lbs. (12 Nm). Rotor Tire and wheel assembly.
You can go to autozone.com and register for free online repair manual with everything you need.

Jan 19, 2010 | 2004 Chevrolet Silverado 2500 Crew Cab

3 Answers

Replace front wheel bearing is it hard to do on 2002 alero


its actually pretty easy if you have the basic tools needed and a little mechanical knowledge, because i dont think you can buy just the bearing at a auto parts store. they sell you the whole hub assembly which is great for the DIYer.

lift the car off the ground and block it from rolling and place a jack stand under it so it cant fall on anyone.


Wheel Bearings printpage_icon.gif

Removal & Installation

These vehicles are equipped with sealed hub and bearing assemblies. The hub and bearing assemblies are non-serviceable. If the assembly is damaged, the complete unit must be replaced.
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    WARNING DO NOT allow the caliper to hang unsupported from the brake hose.


    Front wheel Halfshaft nut and washer Caliper from the steering knuckle and support it aside


    Brake rotor Anti-lock Brake System (ABS) connector, if equipped 3 hub/bearing assembly bolts Halfshaft from the hub/bearing assembly Hub/bearing assembly

    0900c1528023b277.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the front hub/bearing assembly


To install:
Install or connect the following:

Hub/bearing assembly onto the halfshaft, making sure the splines engage smoothly Hub/bearing assembly to the steering knuckle. Torque the bolts to 70 ft. lbs. (95 Nm). Anti-lock Brake System (ABS) connector, if equipped Brake rotor Caliper onto the steering knuckle. Torque the bolts to 38 ft. lbs. (51 Nm). Halfshaft nut. Torque the hub nut to 284 ft. lbs. (385 Nm) on nuts colored black, or 173 ft. lbs. (235 Nm) on gray colored nuts. Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Jul 27, 2009 | 2004 Oldsmobile Alero

1 Answer

2002 chevy 1500 4X4 pickup front wheel bearing assembly


Just to make sure they are a sealed hub and bearings...remove the brakes and rotor and on the back side of the hub there is four bolts remove them, remove outer nut on CV shaft, then pull hub from housing. clean hub seating area then reinstall.
Was thinking that's what i did on mine, just becareful when you place the ABS sensor back. line it up so you don't have to take the wheel back off. Good luck and hope this helps

Apr 10, 2009 | 2002 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...