Question about Toyota Celica

1 Answer

What will keeping it from starting

1 wite sensour not plud to anything the red coming form to motor not plud to anything

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 75,797 Answers

The following are the general instructions on the start of diagnosing any electronically controlled engine or transmission problem.

The engine and the automatic transmission (transmission control is only for automatics, engine is still computer controlled no matter the transmission type) in this vehicle are computer controlled and in most cases when a fault occurs a fault code is stored in the memory of the computer control module. There are exception to this, such as the Mass Airflow Meter and fuel pressure problems. What must be done is to have all the basic testing done such as a scan of the system for fault codes as well as a check with a live data scanner tool for engine functions that are not within range of normal, a trained technician is required to know what is correct and what isn't, then based on careful diagnostics done from a factory repair manual the correct part is replaced or the wiring repaired or the computer replaced (known as the PCM), which is very rarely the problem. Other basic checks must be done as well such as mechanical problems with the engine as well as engine state of tune and mileage on the engine. The transmission can have mechanical issues as well such as no gear engagement at all or a failed pump or other pressure related problems. Also engine mechanical problems can and do cause many drive-ability related problem such as rough idle and other symptoms.

Posted on Oct 26, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My trailblazer wont start now i have secty syem flazer in it


Could be the anti-theft system. The chip in the key could have failed, or one of the components in the security system.
Have you tried a spare key ?

Jul 11, 2014 | 2004 Chevrolet TrailBlazer

1 Answer

Why won't my 1992 geo prizm fire at all???


1. Though the relay may be clicking test the wires coming into the coil. Use a test light to probe the auxiliary wires if it does not light up, trace the wires and look for a break. If it lights the test light refer to #2.
2. Try to start the engine while testing the wires, if no power coming into coil follow wires to fuse box.
3. If no breaks found on wites look into getting a new PCM

Nov 18, 2012 | Cars & Trucks

1 Answer

1991 pickup 22re motor starts for 2seconds and then stalls or turns over and no start. Once in a great while will start and stay running but doesnt run smooth. Acts like its running on two or three...


hav you check your plugs after it happens? a black plug will tell it has too much fuel, a wite plug no fuel at all, leads tours a faulty cold start injector, you can also try to keep it alive with carb or throtle cleaner if idles you not getting enougth fuel. keep in mind compresion test, and valve adjust, this engines require it has a regular service.
good luck

Apr 15, 2012 | 1991 Toyota Pickup

1 Answer

I have Subaru legacy 1995. When I start the engine it chokes immediedly down. There is pleanty of fuel..but have the check engine light coming on and off. The sensour was replaced 3 years ago.


Check your fuses. If you can have your car hooked up to a computer and check the code. The code will tell you where to start. Check your spark plugs and wires. Check for broken vaccum hoses or wires.

please read this may help

http://www.2carpros.com/articles/engine-misfires-or-runs-rough

Nov 22, 2010 | 1995 Subaru Legacy

1 Answer

What does o2 sensour heater circuit bank 1 sensor 1 code mean?


It means you have a bad oxygen sensorThe way you know witch one is bank 1 is the cloest o2 sensor to the front of the vehicleits in the y pipe likely on the drivers side that would be bank 1 sensor # 1 if the closest one to the front is on the other side then that would be bank 1 sensor # 1

Nov 20, 2010 | 1997 Honda Accord

1 Answer

2002 Town & Country, 3.8l engine. I am experiencing black smoke & inconsistent idling & stalling, black smoke form exhaust, air conditikon clutch not working, interior temp gage not working. ...


CHECK FUEL PRESSURE.IT SHOULD BE 53 - 63 PSI YOU COULD HAVE A BAD FUEL PRESSURE REGULATOR OR BAD MAP SENSOR.AC CLUTCH NOT WORKING.CHECK FUSE AND RELAY.IF ALL IS GOOD YOU HAVE LOW REFRIGERANT HAVE IT CHECKED.IF ALL IS GOOD AC COMPRESSOR CLUTCH OPEN OR COMPRESSOR FAULTY.THE INTERIOR TEMP GAUGE NOT WORKING COULD BE LOOSE WIRE OR ENGINE HAS A BAD OPEN COOLANT TEMPERATURE SENSOR.

Aug 21, 2010 | 2002 Chrysler Town & Country

2 Answers

Heater blower not working, comes on and off randomly...it's a 97 isuzu rodeo 2wd


find the motor unplug it them plud it back in and check the groung on the motor se if it is loose

Feb 01, 2010 | 1997 Isuzu Rodeo

2 Answers

Detected misfiring 1 3 5 cylinders on 2006 nissan pathfinder


your distrubitor might be dirty, could be time for new spark plugs

Sep 07, 2009 | 2006 Nissan Pathfinder

1 Answer

My 1996 windstar has no spark or fuel. My husband


just fixed 1 secend relay on left lost its ground in box by bat car had no spark no fuel pump look by d/s strut about 10 inc down u should see 2 wires red / wite put power to red if it starts u lost ground at that relay u have to remove bottom of relay box to fix dont just run power to red wire as repair

Jun 29, 2009 | 1996 Ford Windstar

2 Answers

Blower motor


you will need to remove your glovebox to gain access to your blower motor

Sep 10, 2008 | 1993 Ford Thunderbird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...