Question about Cars & Trucks

Open Question

Alarm and imobilaser remove control not work. how to replace new remove control?

Posted by on

  • yadayada
    yadayada Oct 26, 2012

    how do you replace remove control, makes no sense.

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Truck wont start


You can try inserting the key into the ignition, turning it to the run position (without trying to start it), and switch the valet switch on. Turn the ignition off and try to start the SUV. If that doesn't work the remote will need to be fixed. Either replace the battery or have the remote replaced. If the problem is within the alarm control module. you may need to have it removed or replaced. The system can not be bypassed. If you have other questions, please feel free to write back. Good luck.

Jan 15, 2014 | 1997 GMC Yukon

1 Answer

Problem is: Truseal model car alarm system TS2 - doors not locking, LED light not flashing on dash. how is this fixed


does alarm turn on off? sounds like several relays in alarm controller are not working, might be able to get new controller or have to replace it. if no clicks relays are gone

Jun 09, 2012 | Cars & Trucks

2 Answers

I have a ford explorer 1994 i lost the control remote, Installed a new alarm, but technician can not uninstall the factory alarm How can I do this? when new alarm is on, and opened the doors whit new...


Why not just get the factory PATS System working correctly. You can't remove the factory system,it's an integral part of you vehicles systems and processors

You can get new remotes and program them!!

May 26, 2010 | 1994 Ford Explorer Limited

1 Answer

Cobra alarm


After market alarms are horrible on MB's as they have built in alarms. If you mean the remote your going to have to get the frequency code from the manufacturer or have the dealership program it to control the alarm if the last 1 did.

If you dont know how the system works I would suggest removing it as most systems dont work well with the pneumatic central locking and fail by burning up wiring it is connected to.

May 03, 2010 | 1990 Mercedes-Benz Mercedes Benz Sl Class

1 Answer

My alarm button wont work even with a new batterey in it, can I still open the door with the key without the alarm going off?


only if it a factory alarm, if its aftermarket you will need a new control,try it with the key and see if that works, if not then i think your better off removing that alarm,it may be to old to get a control or the module may have gone bad.

Mar 10, 2010 | 1994 Toyota Celica

1 Answer

Car sat for six months. Battery went dead and replaced with new one. Got it started after new battery, now it won't start, the alarm led is either flashing bright or very dim flashing fast. I'm sure that...


When alarm goes off,put key in ignition and turn,the alarm should go off and alarm should be reset.Or,remove positive battery cable,wait 10 minutes,reconnect,when you open door,alarm will sound,insert key in ignition and turn key and alarm should go off and alarm should be reset.

Aug 14, 2017 | 1994 Toyota 4Runner

3 Answers

Alarm goes off intermittently and has run the battery down. It is happening every other day or.


Your Alarm sensor is set to high *sensitivity level*...either have sensor adjusted or disconnect

Aug 28, 2009 | 2003 BMW 5 Series

1 Answer

Replace my control remote for my ignition started & alarm system


there should be a button some where that you can push while the key is in the on position and it will stop the alarm for that ignition cycle. Then i reccomend taking the alarm out or take it to a reputable electronics shop and they can tell you what manufacture and model is.

Jul 28, 2009 | Mitsubishi Lancer Cars & Trucks

1 Answer

Does any body know how to reset the ML350 alarm??....The remote control doesn't work after i replaced a new battery to the remote control. I couldn't even use the remote to lock/unlock the car. I was


SOME OF THE REMOTES REQUIRE THAT THE KEY BE IN THE IGNITION, IN THE ON POSITION. TAKE THE BATTERY OUT AND WAIT 10 MINUTES. THEN PUT THE KEY IN THE IGNITION AND INSTALL THE BATTERY WHILE THE KEY IS TURNED TO THE ON POSITION. HOPE THIS HELPS YOU. PLEASE KEEP ME POSTED. THANKS FOR AN HONEST RATING AND FOR USING FIX-YA. GOOD LUCK

May 18, 2009 | 2007 Mercedes-Benz ML350

1 Answer

Alarm system not working


A friend of ours did some research and discovered it was the ECU (fuse?) that needed to be reset. We removed the ECU (which controls the cruise control, and "learns" the driving patterns of the driver and adjusts the fuel economy) and the car is running fine. To reset the ECU you need to remove the negative cable from the battery, turn the car to "A/C On" (don't crank the engine) for 10 seconds, then shut it off. Replace the negative battery cable. This should reset the ECU. The car does run much better with the new battery. The previous battery was the original and was approximately 6 1/2 years old so it needed to replaced anyway.

Nov 09, 2008 | Hyundai Motor 2002 Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...