Question about 1991 Toyota Pickup

1 Answer

Clutch problem I replaces the master and slave cylindedr on my 90 toyota PU 4x4 and thought i got all the air out . The clutch worked (ok) for a while but now doesn't Is there other ajustmebt that gan be made. Thanks jason

Posted by on

  • 1 more comment 
  • shelart2u Jan 03, 2009

    You sent me to the pedal airea for a closer look where I found the problem .The left side of the bracket that the pedal is connected hase broaken so the pedal shifts to one sidenott pushing the rod infar enough.First I am going to deill through the bracket and the fire wall and with a nut and bolt see if i can draw the bracket back into position.If this works I wont have th take the whole thing apart and weld it.

    Thanks

  • Anonymous Jan 03, 2009

    my transmission will not engage no matter what what could be my problem

    engin 22 re manual shift

  • Anonymous Mar 04, 2009

    hey i have had the same prob... let me know how u fix it!!!

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 36 Answers

The rod at the end of the slave cylinder can be adjusted. make sure clutch pedal has no more than an inch and a half of free play. If free play is within the 1.5" & still have problem with clutch disengaging, chances are clutch is worn

Posted on Jan 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch not worhing


Is your clutch master cylinder about empty,your slave cylinder could be bad and leaking,also look for leakage at clutch master cylinder,go to transmission and see if leakage is at slave cylinder,here's how to replace,Here's the part.Here's my 85 Nissan 4x4.

Jan 18, 2013 | 1991 Nissan Pickup

3 Answers

Why does clutch leak off and wont go into gear 96 toyota tacoma when you push on clutch pedal goes to the floor it wont engage clutch to be able to put into gear


the most likely reason is either the clutch master cyl. needs to be replaced.or the.slave cyl. its mounted down on the transmation under the hood find the resivore for the clutch. check the fluid level.if its low , fill it back up , and look for signs of a leak
you will probally have to bleed out all of the air from the system.its done almost the same way as bleeding the brakes. Good Luck.

Nov 05, 2011 | Cars & Trucks

1 Answer

I have 1997 Toyota tacoma v6 4x4 I replaced clutch drove next day with no problems got in following and now won't engage/ disengage from gears. if turn off I can put in first or reverse but struggles....


Check the clutch master cylinder and the clutch slave cylinder for proper operation... chances are the slave is bad.. I think this is located on the passenger side of the tranny.. you may have lost fluid during the install.. or introduced air into the system.

If you needed a new clutch.. it was probably time to at least flush that system and or replace the slave cylinder.. also check the spring on the clutch pedal..

I hope you replaced the throw out bearing and pressure plate when replacing the clutch.. I suspect you did.

Best of luck

Mar 26, 2011 | 1997 Toyota Tacoma

2 Answers

Replaced whole clutch and slave cylinder on 1996 Toyota T100 2wd 2mos. ago. Today while driving the clutch hit the floor. I did'nt see any fluid leakage. Any ideas.


Sounds like you need to bleed the system again, or you have an air leak. try bleeding again and just check your fittings for tightness.

Jan 20, 2011 | Toyota T100 Cars & Trucks

1 Answer

I need help changing out the master cylinder in my '94 toyota 4x4 pickup truck. It is a 5speed, i have already changed out the slave cylinder and installed the master cylinder but i still can not get the...


did you bleed the system?? you must bleed the system from the clutch slave. if this has been done, I need more info!! How does the clutch pedal feel, is the clutch slave engaging at all??

Sep 27, 2010 | 1994 Toyota Pickup

1 Answer

1994 4X4 pickup cluch fluid line bleeding . Fliud cyliner has fluid but cluck doed not work


Check the clutch master and slave cylinders for leaks, look behind the rubber boots as the boots can trap the fluid. If all of that is good then you use normal bleeding procedures: step on the clutch, have someone open the slave bleeder to let fluid and any air out, close slave bleeder, repeat.

Feb 19, 2010 | 1994 Toyota Pickup

1 Answer

Chevy l989 4X4 5 speed manual clutch not working


Almost every time a clutch is replaced in a GM with hydraulic release system that system is replaced as well. You can try, and try, and try again to bleed it, but you will eventually replace the clutch slave and master cylinders. Once the slave is allowed to fully extend, it is then virtually impossible to make it function correctly again.

Jul 08, 2009 | 1998 Volkswagen Passat

1 Answer

Clutch issue? 89 toyota PU 4x4 V6 150,000 miles


Yep, you got it. Assuming spring tension on pressure plate feels normal (you should know with 150k mi) then the clutch disk is worn. Time for replacement.

Jun 22, 2009 | 1991 Toyota 4Runner

2 Answers

Clutch


i don't know if you went back to look at my post, but i fixed my car by putting in a new slave and new master cylinder and then tightening up the clutch petal. it does NOT grind anymore! and my baby is like new! it cost me about $90 through napa auto parts. $66 for the master and $16 for the slave and it comes with everything you need. hope this helps you!

Jan 20, 2009 | 1991 Mitsubishi Eclipse

Not finding what you are looking for?
1991 Toyota Pickup Logo

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...