Question about 1998 Toyota Tercel

Open Question

Theres a continuous beep when switching-ON my car, remain constant while driving

When I am switching-ON my car a constant beep starts, which keeps making noise till I switch-OFF the engine. There's no alarm on the panel at all and drive is also normal.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: Engine dies at idle, was slow to start

Two things that I would look at:

1.) The spark plugs should be changed at this mileage

2.) She may be having the beginnings of an Idle Control Valve ("IAC") failure.

The security LED blinking is normal

The horn issue may be a weak battery on the keyless entry remote transmitter

Posted on Oct 06, 2008

Ad
  • 11 Answers

SOURCE: car makes a clicking sound and then just dies

your car is over heating but even if you look at the temp it could be wrong if there if no water on it to tell it the temp but like motor 1258
said check your cooling system and also go to a shop that will see if you need to replace your head gasket also thermostat may be stuck. hop that helps

Posted on Nov 30, 2008

  • 54 Answers

SOURCE: Intermitant temperature

Check to make sure your thermostat works right by monitoring the warming up of your engine. With a completely cold engine, start and run the engine for a few minutes, then put your hand on the top radiator hose to monitor if and when it gets warm as the thermostat opens more and more and note the gauge reading( if it works) the top radiator hose should be unbearably hot within 5-8 minutes. If the therm. opens right it should close right aswell, staying open a little while eventhough the radiator may have cooled may be what you are experiencing causing the rapid cooling and is nothing to worry about. The Hose should not get warm very soon after starting the engine. Regarding you gauge, lets take one step at a time, verify proper op. or the therm.

Posted on Jan 20, 2009

  • 55 Answers

SOURCE: 1990 toyota camry won't start

Usually if you hear the starter solenoid click but the starter doesn't crank, its the starter. And since it was after a trip that is usually when starters are bad when they get hot.

Posted on Apr 25, 2009

  • 226 Answers

SOURCE: 2005 Toyota Corolla Car Alarm Problem

you may have to disconnect the battery for a minute or so ,this will reset the alarm. check your remote it does have a battery in it. otherwise you have to look for a fuse somewhere under the dash close to the fuse box.each one is diff. depending if it original toyota or aftermarket alarm.

Posted on Aug 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2006 Lexus rx400h check VSC system light came on and it's making a loud beeping noise continuously while driving? Help please!!!!


check your brake pud,theres sensor in your brake pud thats why the vsc system appeared in the dashboard..thats you her a sound

Sep 05, 2017 | Lexus Cars & Trucks

1 Answer

How do I eliminate constant beeping from parking sensor while driving?


What do you mean "parking sensor"?
Do you mean the parking brake is on, or is the seat belt not being used?
You should be able to tell where the sound is coming from.

Jul 29, 2015 | Cars & Trucks

1 Answer

Why i hear constant beeping in my 2012 Jetta ?


Beeping with no lights on normally means a dis-connected wire to the oil pressure sender. Check the connection to the oil pressure sender and the wire too for internal damage.

May 04, 2014 | Volkswagen Jetta Cars & Trucks

1 Answer

On unlocking car constant beeping sound, this continues even when car is running, beep however changes when ignition is touched but then returns to constant beep beep beep. the central locking failed on...


Listen for the source of noise its a relay sized speaker thingy mounted in the fuse box inside the car ,locate and pull it out its easier than trying to locate the fault

Nov 29, 2013 | Suzuki Swift Cars & Trucks

1 Answer

2004 chevy malibu I constantly hear a beep inside my car. What can it be?


The beeps happen when speeding up and passing other car

Jan 18, 2012 | 2004 Chevrolet Malibu

1 Answer

I have a 95 jeep grand cherokee, when i put the key in and start my vehicle the key in ignition signal will not stop beeping.Please help me stop the constant beep.


Seems like the vehicle is sensing that one of the doors is remaining open(the door switch may be bad and stuck open. You can also track down and disconnect that buzzer, which is located under the dash.

Aug 21, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

The "low oil pressure -


It could be. The best is just follow your instruction manual on what type the oil should used on your car. But since your car is has the year 2006, it should use specs. API... SL or SM. The viscosity will has range 5W30 -10W40. Again don't get be cheated by the newest oil products, The best oil for your car is the one recommended on your manual in many aspects.
Regards, Jay

Feb 06, 2011 | Chevrolet Impala Cars & Trucks

1 Answer

Obd2 system rediness status won't clear so I can run the smog test due to replacing the battery.


takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

Sep 15, 2010 | 1998 Mitsubishi Eclipse

1 Answer

The oil light keeps flashing with a beep beep sound. i changed the oil pressure switch and the problem still continues.


DON'T DRIVE IT !!!! DON'T START IT AGAIN UNTIL YOU PUT A TEST GAUGE ON IT. you MUST have a gauge put on it to check for pressure. flashing and beep beep mean no pressure... not good. explain in detail how/when this happened ??

Dec 08, 2009 | 2001 Volkswagen Passat

1 Answer

Stop light and handbrake warning sign keeps coming up on my dash


You need to top up your brake fluid right up to the max line - works a treat!!!

Dec 07, 2008 | 1986 Renault Sport

Not finding what you are looking for?
1998 Toyota Tercel Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...