Question about 2004 Chevrolet Silverado 2500HD

Open Question

How to tune up my chev silverado 2500HD truck with a 6.0 engine

6.0 vortex engine what do I need to tune it up

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ajkill
  • 2035 Answers

SOURCE: need schematic for location of ECM on 2002 Chev Silverado 5.3L GAS ENGINE

Please use this link :

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152801b6773


Good luck...

Posted on Aug 14, 2008

  • 341 Answers

SOURCE: 1991 CHEVROLET SILVERADO 2500HD 7.4 Litre 4x4 tow capacity

you can pull the boat no problem. as putting in a 6.2 for the 454 you will need to change wire harness inside and out..im the brake booster...... the gear ratio in the rear ends ..fuel pump ..im guessing you have a truck you will be using for parts.. if you are doing for fuel mileage you will be disappointed you will only gain a couple of mpg .. hopes this helps

Posted on Dec 08, 2008

  • 508 Answers

SOURCE: locate the oil sending unit on a 2003 6.0 2500HD silverado

You will find it down by the oil filter.

Posted on Feb 07, 2009

  • 54 Answers

SOURCE: 96 Chev Silverado having to crank 3 - 4 times before start

Well the only thing i can think of is when your fuel is below half a tank the pressure relief valve and a rubber hose between the pump and the fuel line is exposed. Its possible your fuel is leaking back into the gas tank as it sits overnight, ect. You may want to perform a fuel pressure check when the the gas is at 1/4 tank and been sitting for awhile, pressure should hit 55 seconds after key is turned to run position.

Posted on May 13, 2009

mcgyver468
  • 710 Answers

SOURCE: how do I change the ac belt on my 2500HD Silverado.

UNDER THE HOOD IS A DIAGRAM OF HOW THE BELT IS ROUTED. TAKE NOTE OF THE WHITE STICKER ON THE FAN SCHROUD, JUST ABOVE THE FAN. THE TENSIONER PULLEY IS THE ONE YOU NEED TO ROTATE IN ORDER TO RELEASE THE TENSION ON THE BELT FOR REMOVAL. USING A 15 OR 16 MM SOCKET, ROTATE THE TENSIONER UNTIL YOU RELIEVE THE TENSION AND SLIDE THE BELT OFF ONE OF THE SMOOTH PULLEYS. THEN RELEASE THE RATCHET EASY SO IT DOESN'T SPRING BACK UP. UNRAVEL THE BELT AND INSTALL THE NEW ONE USING THE DIAGRAM. JUST A HINT: IF THE PULLEY HAS RIDGES THEN THE BELT HAS TO BE ON THE RIDGED SIDE OF THE BELT, IF IT HAS A SMOOTH PULLEY, THEN IT RIDES ON THE OUTSIDE OF THE BELT. WHEN YOU ALMOST HAVE THE BELT ON THE LAST PULLEY, ROTATE THE TENSIONER AGAIN AND SLIDE THE BELT ON THE LAST PULLEY. IT HELPS IF THE LAST PULLEY IS A SMOOTH ONE. HOPE THIS HELPS ENOUGH TO FINISH THE JOB. PLEASE KEEP ME POSTED. THANKS FOR AN HONEST RATING AND FOR USING FIX-YA. GOOD LUCK.

Posted on May 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 chev 1500 w/6 cyl vortex, started running rough, then smells like gas, now engine light comes on and white smoke


Either your fuel injector assembly or fuel pressure regulator has gone bad. The intake cover (upper plenum) needs to be removed to inspect both. This motor has an internal pressure regulator that is prone to leaking, should be pretty obvious (puddles of fuel under and around regulator). If you remove the cover and see no fuel then suspect fuel injector assy. It has been updated to a new design so don't be alarmed if it looks different than the old one. Good luck

Oct 02, 2013 | 1999 Chevrolet Silverado 1500

1 Answer

Need firing diagram for 1998 Chev S-10 vortex V-6


sitting in truck right side of engine is, 2,4,6 & left side is 1,3,5

May 21, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

I need the diagram for the vortex distributor that shows the numbers of each wire. I have a 99 Chev 1 Ton 454 vortex


1,3,5,7 are the driverside front to back
2,4,6,8 are the passenger sider front to back

hope it helps

Apr 12, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Power steering pump replacement on 2002 chev


u will need 2 special tool to remove and reinstall the powersteering pully
it must be removed to acess the bolts to replace the pump and a new pump dose not come with pully

Nov 26, 2009 | 2002 Chevrolet Silverado 2500HD

1 Answer

2004 chev silverado 2500 4x4 engine light keeps coming on. First time re tightened gas cap and went out now its back?


try disconnecting the battery cable and wait 10 min.then reconnect, may reset the light,allso check the fuel lines metal and rubber lines,you may have a bad connection somewhere.allso gas cap may need to be replaced,that worked on my truck, try the simple thing first to save money on something you don"t need,

Sep 05, 2009 | 2004 Chevrolet Silverado 2500HD

1 Answer

2006 gm rds radio is locked need to unlock it


I have a 6 disc AM/FM RDS Radio from a 2003 Chev Suburban that I purchased used and installed it into my 2003 Chev.Silverado and it went into lock up after I Installed it.How do I unlock it

Mar 29, 2009 | 2006 Chevrolet Silverado 2500HD 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...