Question about Cadillac Escalade

Open Question

I can not get my brakes bleed my 2000 escalade

I have replaced my pads, capilars, and drums on 2000 escalade and they still wont bleed. what else can I do

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 231 Answers

SOURCE: 2000 Silvrado z71 4wd Brake Pad Replacement

crawl underneath the front and look at the caliper if it has a duel piston caliper you will see 2 circles about 3 inches across and if it is a single piston caliper it will only have one of these circles in the middle this iswhere the pistons are. yes those pads are suitable. As for bleeding the brakes you need to start at the passengers side rear wheel and bleed it first then go to the drivers side rear wheel then go to the passengers side front wheel and then finally the drivers side front wheel. If you are only replacing the brake pads and shoes then you don't need to bleed the brakes. If you are bleeding the brakes then you will want to be sure to top up the brake fluid as you are doing thebleeding process as if you don't you will end up having to start all over again. as for special tools you may need a 3/8 hex bit and a 8 inch " C " clamp to compress the calipers after you remove the brake pads. If you are replacing the rotors you may require a special socket fo dis-assebleing and re-assembly of the front hubs.

Posted on Oct 09, 2008

SOURCE: how to Remove rear brake drum to replace pads.

hi! the pads will be rutted into the drum, you need to release them first with the cables backed off and the cams wound down, then just tap off the drums!

Posted on Dec 20, 2008

  • 82 Answers

SOURCE: 1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks

have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Posted on Mar 11, 2009

  • 1861 Answers

SOURCE: cant fit drums over pads

You need to retract the brake shoes, via the center adjuster mechanism. As your old brake wore, the adjuster moved the shoes outward. Simply move the adjuster to retract the shoes, then slide the drum on. Then, readjust the rear shoes.

Posted on Apr 06, 2009

  • 334 Answers

SOURCE: I need a diagram on how to replace rear brake pad

get a haneys repair manual. at the auto parts. the book has what your looken for

Posted on Aug 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 cadillac escalade brake problem


did you bleed the brakes after changing the pads?

Jul 28, 2013 | Cars & Trucks

1 Answer

I have a F150 p/u 2000 for 10yrs. Each year I change the brake pads. But the rear pads still looks like new. The front pads are worn down. What can be causing the problem?


normally, you replace the rear brake pads every other change in the front brake pads. for your case, it seems that the front brakes are the only ones working.

bleed your brakes to check if rear brakes are still working. after bleeding, check your brake master if it puts pressure equally to the 4 brakes.

Aug 05, 2011 | Ford F-150 Cars & Trucks

1 Answer

How to trouble shoot the brake system?


To trouble shoot the brake system you have to check:AntiLock Brake System ABS:
Hydraulic Modulator
Basically this unit holds steady or bleeds off pressure in brake line, as necessary, when the Electronic Brake Control Module (EBCM) detects an abnormal deceleration in the speed of the wheel. On 2000 and later models the EBCM and Brake Pressure Modulator Valve (BPMV) are mounted on a bracket attached on the left strut tower.
Wheel Speed Sensors, brake fluid level, brake hoses and lines, inspect and replacement, Brake hydraulic system-bleeding, Brake light switch, check, adjustment and replacement.
Disk brake caliper, disk brake pads, drum brake shoes, master cylinder, master cylinder reservoir, O-rings replacement, parking brake adjustment, parking brake cables inspect and replacement, parking brake shoes-replacement, power brake booster, check or replacement, wheel cylinder inspect and replace.

Oct 10, 2010 | 2000 Chevrolet Venture

1 Answer

I drive a honda accord v6 2000 model. the engine is in good shape but the braking is very poor. It is very dull to response and at times i fear it may fail.. i have changed the brake pads but still it is...


Bleed the brakes on all four wheels, and if the rear brakes are drums, adjust the shoes so they are tighter against the drum for better braking overall.

Aug 22, 2010 | 2000 Honda Accord

1 Answer

Video for replacing front brakes pads and rotors on a 2004 ford e


Hello,
ccr20011001bb00.jpg Brake Bleeding
Purging air and moisture from your binders
CarCare - Maintenance - Brakes

ccr20030701as00.jpg ABS Speed Sensor Service
A clean sensor is a happy sensor
CarCare - Maintenance - Brakes

ccr20030701db00.jpg Drum Brakes - Rear Brake Drum Adjustment
It's stupid not to adjust your rear drum brakes
CarCare - Maintenance - Brakes

ccr20050201rr00.jpg Replacement Rotors
Friction, brake rotors, and you
CarCare - Maintenance - Brakes

ccr20050501pb00.jpg Power-Bleeding Brake Systems
Air today, gone tomorrow
CarCare - Maintenance - Brakes

ccr20050701bp00.jpg Replacing Brake Pads
How to replace worn pads
CarCare - Maintenance - Brakes

ccr20071101bs00.jpg Bleeding Power Steering
Getting rid of that air in there
CarCare - Maintenance - BrakesThanks

May 29, 2010 | 2004 Ford Escape

2 Answers

1999 Chevy Tahoe- Soft Brake Pedal


Try having the dealer flush and bleed your system. It is very hard to bleed ABS systems yourself and have safe brakes that still work afterward. Bleeding non-ABS brakes yourself is easy not the same for ABS brakes. Valving, sensors and what-not require a tech and the correct equipment in my opinion. You do it wrong and you could ruin your ABS system. Do that and see if they firm up. I replaced my brake shoes/pads at the same time all new everything in back, drums/springs everything and new rotors up front. then I had the chevy dealer flush, refill and bleed system. Stiffer pedal and brakes work better. Keep in mind the brakes on 99 Tahoes are inaedequate, require new rotors often, heat up and fade/glaze pads regularly. I replace my pads long before they wear down because they glaze up and start fading early. I'll rough em up once maybe, next time, new ones. Every two brake jobs, new rotors for me. Just how it is. They will stiffen a bit and work better but they will never be awesome brakes. Just how it is on 99 and earlier Tahoes. Hope it helps. Very important to bleed correctly though. I'll bleed my 83 Toyota 4x4 myself but not the Tahoe.

Aug 06, 2009 | 1999 Chevrolet Tahoe

1 Answer

Replced front brake pads and calipers adjusted


Bleed the master cylinder first. You have to do that before you belled any calipers or wheel cylinder.

Feb 22, 2009 | 1994 Toyota 4Runner

1 Answer

2000 Silvrado z71 4wd Brake Pad Replacement


crawl underneath the front and look at the caliper if it has a duel piston caliper you will see 2 circles about 3 inches across and if it is a single piston caliper it will only have one of these circles in the middle this iswhere the pistons are. yes those pads are suitable. As for bleeding the brakes you need to start at the passengers side rear wheel and bleed it first then go to the drivers side rear wheel then go to the passengers side front wheel and then finally the drivers side front wheel. If you are only replacing the brake pads and shoes then you don't need to bleed the brakes. If you are bleeding the brakes then you will want to be sure to top up the brake fluid as you are doing thebleeding process as if you don't you will end up having to start all over again. as for special tools you may need a 3/8 hex bit and a 8 inch " C " clamp to compress the calipers after you remove the brake pads. If you are replacing the rotors you may require a special socket fo dis-assebleing and re-assembly of the front hubs.

Oct 05, 2008 | 2000 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...