Question about 2005 Chevrolet Silverado 1500 2WD

Open Question

2004 chevy silverado 4.3 p0016 code replaced distribuator before code

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 328 Answers

SOURCE: 2004 Chevy Silverado Heater Switch

It could be the switch or your blower motor resistor.

Posted on Jan 16, 2009

  • 59 Answers

SOURCE: 4-wheel drive won't shift into gear

I take it you have the manual t-case shifter on the floor. If so check all your linkages from the shifter to the t-case, if all appears well, simply disconnect the linkage from the t-case and see if it moves if it does your problem is in the shift mechanism in the t-case. if it still wont move even while disconnected clean and lube the linkage. If this still doesn't do the trick. replace your linkage

Posted on Mar 15, 2009

robslac24
  • 2 Answers

SOURCE: 01 Chevy Silverado 4 X 4 not working. 4WD light

Having the same exact problem but with my 1999 escalade. Thought it was the actuator bought a new one installed it transfer case would engage but front end wouldnt lock. Took it out of housing left it plugged in got a friend to go through all the 4wd for me and the plunger never moved out the actuator. Checked my wiring harness which is a four prong ann it had one hot prong like it is suppose to. Traced wires even replaced dash switch same problem. Taking it to local dealership tom to have it checked for codes. I was told it could be the transfercase actuator even though its workin that actuator is what sends power to the front to engage the actuator to lock the differential.

Posted on Sep 16, 2009

  • 49 Answers

SOURCE: i have a 2004 chevy silverado and the 4 wheel

the most likely cause is the front axle shift motor if bad your your front axle shaft will not lock in.if there is no shifting of transfer case there is also a electric motor that engages that in .

Posted on Oct 19, 2009

  • 310 Answers

SOURCE: none of the selector buttons are lighted and my

check all fuses if good then actautwaiter

Posted on Feb 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you fix a fan speed switch that won't blow until it's on 4 or 5 in a 2004 z71 Chevy Silverado 1500


you need to replace the fan resistor located by fan motor if not there then trace red and black power wires to locate resistor behind or under dash it wont be mounted far from fan motor

Mar 13, 2016 | 2004 Chevrolet Chevrolet Silverado 1500...

1 Answer

2011 Chevy Malibu lt. P0016 code. Replaced both cam sensor.and crank sensor still won't start


If you have the V6, they have a history of timing chain problems. The tensioner can go bad allowing the chain to rattle and jump time. This weill set the P0016 code since the cam and crank are not sync'ed and will result in a no-start condition.

Dec 06, 2015 | Cars & Trucks

1 Answer

How to change the oil pump on 2007 chevy 4.8


Remove oil pan.
Mark and Remove distribuator.
Remove bolts to oil pump and remove.
Install new oil pump.
Reinstall oil pan with new gaskets.
Put in new engine oil.
With a large straight screwdriver. Rotate oil pump (clockwise for top) through the distribuator hole until a huge anount of resistance is felt.
Reinstall distribuator where marked. ( you may have to rotate tang on oil pump to get distribuator to go down. .

Start and run.

Jul 01, 2014 | Cars & Trucks

1 Answer

2004 chevy tb with 4200 motor have codes pop up p0014 n p0016


ck timing , have you had a head gasket replaced before this issue? I have seen clogged cats cause to much back pressure and making timing jump a tooth . or you have timing out due to timing gears or stretched chain . Do you have any bearing noise coming from the motor ?

Apr 08, 2013 | 2004 Chevrolet TrailBlazer

2 Answers

Ml350 replaced a/b cam position sensor reset computer & and erra codes p0016/p0016 check engine ligth is reset car drives with light off when engine is turn off and started the light goes out if you...


P0010....'A' Camshaft Position Actuator Circuit (Bank 1)

P0011....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0012....'A' Camshaft Position - Timing Over-Retarded (Bank 1)

P0013....'B' Camshaft Position - Actuator Circuit (Bank 1)

P0014....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0015....'B' Camshaft Position -Timing Over-Retarded (Bank 1)

P0020....'A' Camshaft Position Actuator Circuit (Bank 2)

P0021....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0022....'A' Camshaft Position - Timing Over-Retarded (Bank 2)

P0023....'B' Camshaft Position - Actuator Circuit (Bank 2)

P0024....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0025....'B' Camshaft Position - Timing Over-Retarded (Bank 2)

I think your sensors are pattern parts and the readings /resistances are not the same as the original parts ,try some bosch units is my first suggestion ,

Nov 02, 2010 | Mercedes-Benz ML350 Cars & Trucks

2 Answers

2004 chevy silverado 1500 4 wheel drive wont work..


try selecting from nutreul or less then 3km

Feb 02, 2010 | 2003 GMC Sierra

1 Answer

I have a 2004 chevy silverado and the 4 wheel


the most likely cause is the front axle shift motor if bad your your front axle shaft will not lock in.if there is no shifting of transfer case there is also a electric motor that engages that in .

Oct 17, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

2 Answers

After changing the camshaft censor and the car still wont start what could be the problem also is there a fuse that needs to be replaced this is a 2004 pt cruiser the code say its the camshaft censor also...


P0016 crankshaft/camshaft timing misalignment
p0340 camshaft sensor

intermittent crankshaft sensor

PCM detects an error when the camshaft position is out of phase with the crankshaft position

Sep 26, 2009 | 2004 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...