Question about 1996 Chevrolet Caprice

Open Question

Where is the a/c drain tube for a 2002 Chevy Venture

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 65 Answers

SOURCE: Help changing thermostat 2002 chevy venture

THERMOSTAT REPLACEMENT

Removal Procedure
1.Remove the air cleaner and duct assembly.
2.Drain the coolant until the coolant level is below the thermostat. Refer to Draining and Filling Cooling System .
3.Remove the crossover exhaust pipe.
4.Remove the radiator hose from the thermostat housing
5.Remove the thermostat housing bolts and clean any sealer from the bolt threads.
6.Remove the thermostat housing and gasket.
7.Remove the thermostat.
8.Clean the mating surfaces.

Installation Procedure
1.Install the thermostat.
2.Install the thermostat housing and gasket.
3.Install RTV sealer, GM P/N 1052366 or the equivalent, to the thermostat housing bolt threads. .
4.Install he thermostat housing bolts.
Tighten
Tighten the bolts to 25 N.m (18 lb ft).
5.Install the radiator hose to the thermostat housing.
6.Install the crossover exhaust pipe
7.Install the air cleaner and duct assembly.
8.Fill the cooling system. Refer to Draining and Filling Cooling System .
9.Inspect the cooling system for leaks. Repair as necessary.


http://www.2carpros.com/forum/automotive_pictures/99387_Graphic2_59.jpg

http://www.2carpros.com/forum/automotive_pictures/99387_Graphic3_26.jpg

http://www.2carpros.com/forum/automotive_pictures/99387_Graphic4_13.jpg

Posted on Mar 30, 2009

grendelynn
  • 5 Answers

SOURCE: fault code p0440 CHevy venture

I had that exact code a couple weeks ago. Mine needed new oxygen sensors. They(there are 2, only one was throwing a code, but I had both replaced) cost a little over $100 to have replaced.

Posted on Apr 23, 2010

  • 5252 Answers

SOURCE: why does oil turn pinkish on chevy venture 2002

Is it synthetic blend? I've never heard of regular oil ever turning pink, not even when contaminated with other fluids. Have it looked at by someone. If it's synthetic, maybe it's normal?

Posted on Jul 09, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the heater core in my 2002 chevy venture van


Look for smaller coolant lines coming off the back of the block or going into the firewall pretty sure it's in the dash

Mar 04, 2015 | Cars & Trucks

1 Answer

Pulling off oil pan 2002 Chevy venture


First drain your oil. This does not mean it is totally empty and make sure you do this when your car is cooled down. Hot oil sucks. From there loosen the bolts. There will be 12 to 16 of them. Pull the pan off and there you go. If you do pull this off, plan on replacing the gasket. When putting it back on it is very important to tighten these evenly going back and forth from side to side and not all in a row.

Feb 17, 2015 | 2002 Chevrolet Venture Passanger

1 Answer

CAN 1999 CHEVY VENTURE PARTS BE USED IN 2002 CHEVY VENTURE


A lot of the parts can be used. Not all though, when it comes to engines and transmission.

Sep 08, 2014 | 1999 Chevrolet Venture

1 Answer

Location of orifice tube in 2000 chevy venture


best advice is the method i would use to located the orifice tube in the 2000 chevy venture. check the automotive repair book section in your local library. Most libraries have repair manuals on their automotive shelf section. find the a/c manual for your year and model car. make a copy of the page that has the information you need. you will need to make a copy because the library will not let those manuals be checked out. you might want to google for the location of the orifice tube location. I hope this helps.

Jun 18, 2014 | 2000 Chevrolet Venture

1 Answer

2005 Chevy venture van evaporator coil drain clogged..what's the easiest way to get to it?


dreain is located under the hood in engine compartment on firewall area on passenger side of vehicle, look for a rubber looking hose down low on the firewall, normally you can remove hose and clean drain by blowing air in tube or sometimes crrap collects in the rubber tube, tube should pull right off, i have sneeped off end of the rubber tube so it has a bigger hole to drain and not plug up again

Sep 03, 2012 | Cars & Trucks

1 Answer

Where is the evaporator coil drain on a 2005 Chevy venture van, and the easiest way to get to it?


under the hood on passenger side of firewall, down low where fire wall curves back, will have a rubber tube attached

Sep 03, 2012 | Cars & Trucks

1 Answer

How do reset the security system on a 2002 chevy venture van? and it will not start


Good morning, I am having a problem starting my 2000 chevy venture. I believe its the security system acting up, can anyone tell me how to reset the vechile's security system?

Jul 16, 2010 | 2000 Chevrolet Venture

2 Answers

Fault code p0440 CHevy venture


I had that exact code a couple weeks ago. Mine needed new oxygen sensors. They(there are 2, only one was throwing a code, but I had both replaced) cost a little over $100 to have replaced.

Sep 19, 2009 | 2002 Chevrolet Venture Passanger

2 Answers

Help changing thermostat 2002 chevy venture


THERMOSTAT REPLACEMENT

Removal Procedure
1.Remove the air cleaner and duct assembly.
2.Drain the coolant until the coolant level is below the thermostat. Refer to Draining and Filling Cooling System .
3.Remove the crossover exhaust pipe.
4.Remove the radiator hose from the thermostat housing
5.Remove the thermostat housing bolts and clean any sealer from the bolt threads.
6.Remove the thermostat housing and gasket.
7.Remove the thermostat.
8.Clean the mating surfaces.

Installation Procedure
1.Install the thermostat.
2.Install the thermostat housing and gasket.
3.Install RTV sealer, GM P/N 1052366 or the equivalent, to the thermostat housing bolt threads. .
4.Install he thermostat housing bolts.
Tighten
Tighten the bolts to 25 N.m (18 lb ft).
5.Install the radiator hose to the thermostat housing.
6.Install the crossover exhaust pipe
7.Install the air cleaner and duct assembly.
8.Fill the cooling system. Refer to Draining and Filling Cooling System .
9.Inspect the cooling system for leaks. Repair as necessary.


http://www.2carpros.com/forum/automotive_pictures/99387_Graphic2_59.jpg

http://www.2carpros.com/forum/automotive_pictures/99387_Graphic3_26.jpg

http://www.2carpros.com/forum/automotive_pictures/99387_Graphic4_13.jpg

Mar 30, 2009 | 2002 Chevrolet Venture Passanger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...