Question about Cars & Trucks

Open Question

Keyless micra k12 starting problem. Red key symbol stays red. Fob battery ok.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 54 Answers

SOURCE: clio

the key has lost its code. open the doors manually and use the central locking button inside the car. hold it down and keep pressing your key fob. this should re code the key

Posted on Jul 12, 2008

  • 57 Answers

SOURCE: jaguar s/type wont start had flat battery now replaced x.reg 2000

Yes the key needs to be reprogramed to the car. Unfortunately that will have to be done by the dealer. Make sure that you have plenty of proof that you are the owner. They will reprogram it but you will not take posession of the car until you prove it is yours.

Posted on Jan 04, 2009

onyeredson
  • 404 Answers

SOURCE: mercedes 1999 c200 key fob

Hello Haq!
Could it be the key just needs re-coding? maybe you are worrying to much as £177 would be about right as that would need coding etc., Try phoning your local Merc dealer or take the key and V5 to them for coding (Hopefully)
Good Luck!
Paul 'W'
Onyer~EDson(:0)~[><

Posted on Jan 06, 2009

  • 166 Answers

SOURCE: key fob lights up but doesn't work even with a new battery

I'm more familiar with Range Rovers and Saab's when it comes to key fobs but if you changed the battery you have to re-program the key fob. If you do not have an owner's manual that can take you through the steps you might want to try: push and hold the lock button on the key fob, put it in the driver's side door and turn to lock. With the button still depressed turn back to open, remove the key and release the button. If this doesn't work check any and all fuses associated with your system and last but not least you could take it to a dealer. Good luck!

Posted on Aug 25, 2009

Testimonial: "thanks ill try what you've suggested"

  • 2 Answers

SOURCE: my renault laguna 1999 rt remote key fob wont work?

IF YOU TYPE 1999 RENAULT LAGUNA REPROGRAMME KEY INTO A GOOGLE SEARCH, YOU WILL BE ABLE TO PRINTOFF INSTRUCTIONS TO REPROGRAMME THE KEY TO THE KEY READER.THE IGNITION NEEDS TO BE OFF TO DO THIS

Posted on Dec 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why isn't keyless entry working?


Remove the battery and have it replaced.

Feb 20, 2016 | 2011 Volkswagen Tiguan

1 Answer

My 2009 keyless entry will not start?



Nissan cars with keyless entry will display key on dashboard display if battery of key runs out. Normally it can be resolved by replacing the battery. See video above.

Emergency Start: There is a way to start the car in case of emergency. If you don't have access to new battery then you can start the car by pressing the button with your key FOB. There is a sensor in your key below Nissan logo which should be kept near the Start-Stop button when pressing it. This should work even if there is no battery in the key. You can give it a try.

Feb 05, 2013 | 2009 Nissan Sentra

1 Answer

Mercedes s420 keyless entry reprogram


What year model is youre S420 and do you have key with 3 buttons and a card with one button. More detail please

Jan 15, 2013 | Mercedes-Benz ML320 Cars & Trucks

1 Answer

Red light car symbol and engine not starting


looks like the immobilizer has been activated or the ignition key you are using either is wrong or lost the program and can not communicate with the ignition switch by not giving signal to start. Better to apply to an expert to help you.

Nov 12, 2012 | Cars & Trucks

1 Answer

USE OF THE INTELLIGENT KEY SYSTEM


yes, they can fix it in about 10 minutes

Aug 27, 2012 | Nissan Cars & Trucks

1 Answer

Key fob wont re set on my ssan yan rexton


I recently changed the battery on my key fob for my ssanyong rexton. I then did the following for the key fob to make it work. 1. Enter vehicle and close all doors.

2. Put seatbelt on (or clip it into the buckle) to shut the warning buzzer off.

3. Put key in ignition, turn to run position but don't start it.

4. Press and hold both buttons on key fob until red light on fob stays on. Then let go of both buttons. Then pressed the alarm button then the panic button, somthing like that. To be fair the button sequence after the red light came on is a bit vague. The alarm was blaring so i was happy when it just stopped.

May 23, 2012 | SsangYong Rexton Cars & Trucks

1 Answer

Sorry my car was not listed so picked Altima 2003 Micra Intelligent key fob not working properly. Can drive the car but cannot open or lock the doors. Did get fob wet. Now dried out. Worked for first few...


You are going to need to check the power lock control moduel on the inside of the door panel. If the FOB appears to be working but the doors are not unlocking, you need to check this. I would also replace all fuses that control the locks. If both of these devices check out ok, you may need to replace your FOB. To check your power lock control moduel, manually lock and unlock your doors by pressing the lock button on the inside of the door. If it does not work, it is either the fuses or the power lock control moduel. If it works, your FOB has gone bad. Hope this helps! Please rate 4 thumbs up!

Apr 18, 2011 | Nissan Altima Cars & Trucks

2 Answers

Car wont do anythin


take your fob to a dealer or locksmith,sounds like the battery's dead.

Sep 21, 2009 | Renault Sport Cars & Trucks

1 Answer

2005 key fob controls do not open locks


The key fob will have a very small opening along the seam. Use a small flat head screwdriver to prey the seam apart.

Sep 05, 2009 | 2005 Scion xB

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...