Question about Cars & Trucks

1 Answer

If you undo the battery will it reset the inspection light

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 80,637 Answers

In some models yes and others no.

Posted on Oct 26, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

This light stays on and the passenger seat belt light, the ignition is in the off position. It drains the battery. 98 Oldsmobile cutlass

it might be that the ignition backing is worn and there for not turning it all the way down although the key shows its off the backing is still in on position
u will need to take steering covers off and undo the plastic backing at the back of the ignition to inspect it

Jun 11, 2015 | 1998 Oldsmobile Cutlass

1 Answer

Reset engine light for nissan xtrail qr20 2004 model

undo battery terminals for count of ten

if engine light returns there are fault codes to be read
from the ECU

Nov 08, 2013 | Nissan Altima Cars & Trucks

1 Answer

My 92 88 royal osmobile security light came on and tried both keys wont start dont have alot of money or a dealership in my area what is the best way and cheapest way 2 by pass it

Disconnect the positive termanl on the battery for about 3 min. reconect the battery the computer should be reset. Drive the car for about 30 min. if it takes that long to get to the inspection station then drive there and it should pass as long as the light hasn't come on prior to arriving at inspection station.if so see how long it takes for light to come on go about that far away from inspection station disconnect battery and try again.

Sep 27, 2010 | 1992 Oldsmobile 88

2 Answers

2003 eclipse spyder wont idle has gas can hear fuel pump turn on starts but then stalls

Could very well be failing ( or failed ) Idle control switch. This is found on the throttle body of the engine, air in-take. When operating properly it will vibrate lightly. Typically this is held in place by two small screws, 8MM or so. It can be unplugged, removed and easily cleaned/inspected.

I hope this may have assisted,

May 21, 2010 | 2003 Mitsubishi Eclipse Spyder

1 Answer

How do i reset MY maintance light

undo the battery post and reconnect it see of this helps it might reset the computer

Apr 14, 2010 | 2000 Pontiac Sunfire

1 Answer

Reset the check ingine light

if you undo the red cable from the battery for about a minute then hook it back up it will reset all the codes on the car

Dec 15, 2009 | 2001 Volkswagen Cabrio

1 Answer

How do I reset my check engine light

try undoing the battery for 1 min that will reset the defaults like the check engine light

Aug 08, 2009 | 2006 Chevrolet Impala

1 Answer

I have a Peugot 106 Independence and the battery charger warning light comes on intermittently although this does not seem to affect running. Car had inspection but no fault was found. Does any one have...

If the battery had not been replaced, then this should have been replaced before the alternator.

The alternator belt (serpentine belt) should be well in tension, when this is not in tension, or need to be replaced you get battery warning light.

To put serpentine belt in tension you need to undo the tensioner arm bolt a bit, and move the tensioner pulley. Sometimes you need to hammer the arm with a rubber hammer to do this.

Oct 19, 2008 | Peugeot Liberte Cars & Trucks

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15427 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides