Question about 1992 Toyota Celica

1 Answer

Mounts on side of engine - 1992 Toyota Celica

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 75,797 Answers

Duplicate question.

Posted on Oct 26, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install the alternator belt in a 2008 Suzuki xl-7?


which engine option, you do know belts are not same on all engines right? fact.
2.7L V6 or bigger? IDN.

same on all cars. (answering in generic form do to above)
loosen the tension-er.
take off old
put back new
and if not a spring tension-er,set proper tension
the fSM cover all this.
why not read the manual, RTM?

here is one example (get the book, RTM or see alldata.com)

2008 xl7 engine


Removal Procedure

Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .

Install the engine support fixture. Refer to Engine Support Fixture .

Remove the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

Remove the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Remove the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Lower the vehicle


Rotate the drive belt tensioner clockwise to release the drive belt tension.

Slide the drive belt off of the belt idler pulley (1).

Slowly release the drive belt tensioner.

Remove the drive belt from the accessory drive pulleys.

end remove
beg, install



Install the drive belt to the crankshaft pulley, the tensioner and the generator.

Rotate the drive belt tensioner clockwise.

Install the drive belt to the idler pulley (1).

NOTE

Important: Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.

Slowly release the drive belt tensioner.

Raise the vehicle.

Install the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Install the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Lower the vehicle.

Install the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Remove the engine support fixture. Refer to Engine Support Fixture .

Install the the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .
end.

Sep 07, 2014 | 2008 Suzuki XL7

2 Answers

I want to know how many engine mounts a 1997 sl2 saturn uses and if there is a diagram where I can see their locations in the car. Tanks


4 total. Two on the passenger side (upper and lower) and two on the driver's side, upper and lower. The "dog bone" type strut mount is the same for either side.


Jul 04, 2011 | Saturn SL2 Cars & Trucks

2 Answers

How do i replace my spark plug wires in the rear of my 97 chevy lumina? do i have to take the engine mounts off and pull it back?


No, you don't have to remove the engine mounts and pull the engine back, and this is inadvisable. It can be a challenge to get to the plugs on the firewall side of the engine. Here are some suggestions.

1. You can try to reach the plugs blindly by feel. This can be frustrating and time consuming, but patience and persistence can pay off.
2. You can remove obstructing components such as the coil/ignition module assembly, alternator, vacuum hoses, etc. as applicable.

Feb 24, 2011 | Chevrolet Lumina Cars & Trucks

1 Answer

Trying to remove an alternator from an 06 altima


Removal and Installation L4-2.5L (QR25DE) Engines To Remove:
nis_alt_l4_alt.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Engine cover
    • Front/right-side engine undercover
    • Drive belt
    • Alternator harness connector
    • Engine ground wire from top mount
    • Alternator upper and lower mounting bolts
  3. Set the alternator aside and remove the top mount.
  4. Remove the alternator.
To Install:
nis_alt_l4_alt1.gif

  1. Slide alternator in place.
  2. Install or connect the following:
    • Alternator top mount
    • Alternator upper and lower mounting bolts
    • Engine ground wire from top mount
    • Alternator harness connector
    • Drive belt
    • Front/right-side engine undercover
    • Engine cover
    • Negative battery cable
V6-3.5L (VQ35) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Drain coolant from the radiator into a suitable container.
  4. Remove or disconnect the following:
    • Radiator
    • Front/right-side engine under cover
    • Drive belt
    • Idler pulley
    • Alternator adjustable top mount
    • Alternator lower mount bolt and nuts
    • Alternator lower front bracket bolt
    • Alternator harness connectors
    • Alternator
To Install:
nis_alt_chg_v6.gif

  1. Install or connect the following:
    • Alternator in place
    • Alternator harness connectors
    • Alternator lower front bracket bolt
    • Alternator lower mount bolt and nuts
    • Alternator adjustable top mount
    • Idler pulley
    • Drive belt
    • Front/right-side engine under cover
    • Radiator
  2. Replace the engine coolant.
  3. Connect the negative battery cable.
  4. Start the engine and check for leaks.
  5. Recheck coolant level and top off as needed.
prev.gif next.gif

Oct 15, 2010 | 2006 Nissan Altima

1 Answer

Where is the starter located on a 98 cadillac deville?


3.0L Engine

6b5e9da.jpg

Fig. Typical starter mounting on early models

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle securely on jackstands.
  3. Remove the terminal nuts, washers, and electrical leads from the starter motor.
  4. Remove the passenger side catalytic converter.
  5. Remove the passenger side engine mount nuts, and lower the vehicle.
  6. Disconnect the resonance chamber-to-throttle body ducts.
    1. Detach the electrical connector for the Mass Air Flow (MAF) and the Intake Air Temperature (IAT) sensors.
    2. Disconnect the resonance chamber air intake hose from the air cleaner housing and MAF sensor.
    3. Remove the (IAC) inlet hose and the intake plenum air inlet hoses.
    4. Detach the electrical connector from the switchover valve and the remaining vacuum connections.
  7. Install the engine support fixture J28467-A with adapters J28467-450 or equivalents and raise the passenger side of the engine.
NOTE Passenger side of the engine must be raised approximately 1.5 inches (38 mm).
  1. Raise and safely support the vehicle securely on jackstands.
  2. Remove the engine mount from the engine mount bracket and cradle.
  3. Remove the engine mount bracket bolts and reposition the bracket.
  4. Remove the starter motor from the vehicle.
To install:
  1. Install the starter motor to the vehicle and tighten the bolts to 44 ft. lbs. (60 Nm).
  2. Position the engine mount bracket and install the bolts. Tighten to 30 ft. lbs. (40 Nm).
  3. Install the engine mount to the engine mount bracket and cradle. Partially lower the vehicle.
  4. Lower the engine. Have an assistant guide the engine mount into place while lowering the engine. The engine mount locator tab must engage the slot in the cradle.
  5. Reinstall the resonance chamber-to-throttle body ducts.
  6. Raise the vehicle.
  7. Install the passenger side engine mount nuts. Tighten the upper nut to 30 ft. lbs. (40 Nm). Tighten the lower nut to 41 ft. lbs. (55 Nm).
  8. Install the passenger side catalytic converter.
  9. Plug in the electrical leads, install the washers, and terminal nuts to the starter motor. Tighten the battery cable terminal nut to 115 inch lbs. (13 Nm). And the solenoid terminal nut to 35 inch lbs. (4 Nm).
  10. Lower the vehicle.
  11. Connect the negative battery cable.

Good luck (remember rated this post).

Apr 12, 2010 | 1998 Cadillac DeVille

1 Answer

How do you remove and replace engine mounts on 2000 E320


Remove the electric fan. Remonve the drive belt. Lower the AC compressor by removing the three bolts. Do not disconnect the gas lines. Raise vehicle and remove the engine panel. remove upper engine mount bolts. Raise engine and remove lower engine mount bolts. Then remove engine mount.
These instructions are for removing the engine mount on the left side. I haven't done the right side .

Jan 14, 2010 | 2000 Mercedes-Benz E-Class

3 Answers

Location of motor mounts on 94 saturn sl1 where are they and how do you replace them? (all of them) or at least the major ones


There are four total mounts.

1. Upper engine mount located on the passenger side of the engine. Get this at the dealer, aftermarket, especially Anchor brand are garbage.

2. Lower engine mount, often refered to as a "dog bone" mount because of its shape. This one is located on the lower passenger side. You'll have to remove some splash shields to get to it. Aftermarket is OK.

3. Upper transmission mount, also refered to as a "dog bone" mount. Located under the battery.Aftermarket is OK.

4. Lower transmission mount. Located under the transmission. As with the top engine mount, dealer is better quality.

The two dogbone mounts usualy last a very long time, its the others that fail over time. Especially the upper one.

Jun 17, 2009 | 1999 Saturn SL

1 Answer

93 buick park ave Ultra. replacing water pump...must I remove the front passenger side motor mount??


Yes. Put a jack under the motor and remove 3 bolts from side of engine and the long center pivot bolt in mount and the 2 bolts that go top down into the frame and loosen the 2 bolts below mount. Jack up the motor until you can separate the mount, leaving the engine side in and removing the frame side. The engine side can be moved out of the way without completely removing.

May 06, 2009 | 1993 Buick Park Avenue

1 Answer

Removal and installation of an auto trans in 2002 toyota camry


  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the transaxle fluid.
  3. Remove or disconnect the following:

    Negative battery cable. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding Battery Air cleaner assembly Throttle cable from the throttle body Cruise control actuator cover and connector, if equipped Ground wire Starter Speed sensor connectors, direct clutch speed sensor, and the park/neutral position switch connector on the transaxle Solenoid connector on the transaxle Shift control cable Oil cooler hoses Front side transaxle mounting bolts Front engine mounting bolts Oil cooler line mounting bolts from the front frame Upper transaxle to engine mounting bolts

    0900c15280197a59.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Tie the steering rack to the engine support fixture components, as shown-Avalon and Camry
    Front exhaust pipe Engine side covers and undercovers Both halfshafts Front side engine mounting nut Rear side engine mounting bolts (remove hole plugs) Left side transaxle mounting bolts Steering gear housing Front frame assembly Rear end plate mounting bolts Torque converter cover Torque converter retaining bolts Remaining transaxle mounting bolts Transaxle

Apr 09, 2009 | 2002 Toyota Camry

1 Answer

Engine mounts


The engine mounts are found one on each side about the center of the engine at the bottom at the frame. There is a long bolt with a nut that holds the engine side of the mount to the frame side of the mount.

Jun 20, 2008 | 1998 Chevrolet Blazer

Not finding what you are looking for?
1992 Toyota Celica Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...