Question about 2004 Hyundai Santa Fe

Open Question

2004 santa fe automatic stalls when put in gear

Car stalls when taken out of park or pushing on brake

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 21 Answers

SOURCE: 2003 santa fe

It needs a new pruge valve. The purge valve is sticking open allowing fuel vapors into the intake manifold causing a rich hard start condition.

Posted on Jul 02, 2008

Ad
  • 1 Answer

SOURCE: 2002 HYUNDAI SANTA FE

I had the same problem with a 2003 Hyundai Santa Fe. While driving to work as I pressed on the gas the brake and battery light would come on. When I applied the brake, the lights would go off. When I got to work I turned the car off and then tried to start it, nothing. The car made a funny sound while running and I could smell somethig smoking. I replaced the alternator and all is good again. When removing the alternator the bottom lifts off the mounting bracket, you cannot drive the bottom bolt back through the mount as I tried to. Simply remove the nut on the bottom bolt and remove the top bolt, then lift the alternator out.

Posted on Oct 26, 2008

  • 8 Answers

SOURCE: 02 Santa Fe brake and battery lights wet conditions only

sounds like you got the altenater wet which can cause oxidiseation .yo should check this at a auto electricions

Posted on Jul 07, 2009

SOURCE: How to remove rear brake rotors

THE REAR BRAKE ROTOR IS A LOOSE ROTOR AND SHOULD COME OFF EASILY. IF NOT, IT IS POSSIBLE THAT THE ROTOR IS HELD BY RUST ONTO THE HUB OR THE BRAKE SHOES IS STILL EMBEDDED INTO THE ROTOR. REMOVE THE HANDBRAKE CABLE TO ENSURE THAT THE BRAKESHOES COLLAPSE AND TRY TO LOSEN IT AGAIN. IF SEASED ONTO THE HUB BY RUST, KNOCK THE ROTOR WITH A COPPER HAMMER TO BRAKE THE RUST WITH A RUST REMOVER.

Posted on Jul 15, 2009

  • 84 Answers

SOURCE: Change serpentine belt 2004 Hyundai Santa Fe

it uses a spring loaded tensioner.use a breaker bar to rotate the tension and it should just come off.if u need a pic or anything else to do it let me know,

Posted on Oct 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

5 Answers

2009 Hyunda Santa Fe stalls while driving


I had a similar problem with my Santa Fe. It occurred intermittently but after I turned the steering wheel to the left. After much screwing around by the dealer and trying to baffle me with BS we heard about a strange solution. I am not a mechanic but the problem somehow related to a spring in the Airbag on the steering wheel. Changed the spring and "Stone the flame'n crows" problem solved. Never had a problem since.

Jul 27, 2012 | 2003 Hyundai Santa Fe

1 Answer

2004 Hyundai Santa Fe stalls everytime you put gas in it. You have to wait approximately 5 minutes, then it will start. Doesn't stall any other time. What could possibly cause this?


Did some research and found quite a few people with the same problem. All solutions were the same. Replace the Purge Control Valve, Hyundai part number 28910-22040. It is covered under warranty.

Jan 04, 2011 | 2004 Hyundai Santa Fe

1 Answer

Check engine problem


plug it into a scan tools .it could be a camshaft sensor or crank sensor ,,scan tool can deside this

May 11, 2010 | 2004 Hyundai Santa Fe

2 Answers

2004 santa fe hyundai


it is probably going into a fail safe mode, get it to a dealer and have it scanned for dtc's

Apr 24, 2010 | 2004 Hyundai Santa Fe

1 Answer

Change the back disc Santa Fe 2004 Hyundai


if it has the to screws like the front remove those.then rotate til the plug is at 6 oclock sn remove the plug;insert a screw driver through the hole and rotate the adjuster to back the parking brake shoes away from the drum surface in the disc.

Sep 25, 2009 | 2004 Hyundai Santa Fe

1 Answer

My 2001 santa fe doesn't crank when I turn the key on. Battery is fine, brand new, panel lights and internal lights are ok.


If your car is stick, you have to make sure that the sensor in the brake pedal is ok. It can either be replaced or eliminated.
If it is automatic, make sure it is in Parking and that the indicator light for such is on. If it is not, then the sensor on the lever has to be replaced.
Otherwise, the carbons on the starter engine may be worn and will need to be repalced.

May 11, 2009 | 2004 Hyundai Santa Fe

1 Answer

Parking brake


I just replaced rotors on my 2003 Santa Fe, There are 2 phillips screws in the rotor that must be removed. There is an auto adjuster on bottom of brakes. That inspection hole is very small! Sometimes you must tap a hammer around the drum to loosen the rust. Hope this helps.

Sep 14, 2008 | 2003 Hyundai Santa Fe

Not finding what you are looking for?
2004 Hyundai Santa Fe Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...