Question about Nissan Terrano

Open Question

How do i remove a steering wheel from a nissan terrano 2 2003

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jdwills
  • 15 Answers

SOURCE: nissan terrano headlight

check out
http://www.sferamydlo.com.pl/Zbyszek/Nissan/R20/el.pdf


Bulb Replacement
The headlamp is a semi-sealed beam type which uses a replacable
halogen bulb. The bulb can be replaced from the engine compartment
side without removing the headlamp body.
I Grasp only the plastic base when handling the bulb. Never
touch the glass envelope.
1. Disconnect the battery cable.
2. Disconnect the harness connector from the back side of the
bulb.
3. Pull off the rubber cap.
4. Press end of the retaining pin together to release bulb.
5. Remove the headlamp bulb. Do not shake or rotate the bulb
when removing it.
6. Install the new bulb in reverse order of removal.

Posted on Nov 11, 2008

Ad
  • 279 Answers

SOURCE: remove door trim on nissan terrano 91 4 door

The front doors of the Terrano (D21 Japanese import) are like a jigsaw puzzle, and the bits should fit and come apart without force.
First, look down into the handgrip of the doorpull and you will see a small round plastic plug. Take this out with a sharp screwdriver, and there is the first screw to undo. This allows the handgip to come off, revealing the screw holding the electric window winder switches etc to come off.
The panel of the door itself comes off by carefully pulling the doorcard and the small nylon doorstuds out of the metal frame of the door. Then lift the doorcard up and unhook the the inside door latch wire from the doorcard.
This will reveal the speakers or at least where they should be behind the wire grilles.

As for the alternator belt, may I suggest that you also replace the A/C and the powersteering belts at the same time. Theoretically if one is worn, the others will be,too.
I crawled under the front of the vehicle and took off the splash shield so I could reach up into the crankshaft pulley area.
Both the adjusters for the powersteering andf the alternator can be slackened off from the top of the engine, but I recommend removing the alternator altogether, which allows better access to the adjuster for the A/C belt.Slacken this off.
This tensioner has a roller bearing in the centre of it, take the large bolt out and the tensioner will come off. You will see a bearing in the middle of it, press this out and replace it with a new bearing, it is common and cheap, and if it wears out it will scream very loudly.
Wiggle off the three belts from their pulleys, taking note of their order, and where each drives off the main cranksharft pulley.
Buy the correct replacements (length and Section) and if the belts look like a dog's breakfast, go to someone who can measure them properly. Refit in the correct grooves and pattern, you may have to slacken off the adjusters quite a lot if the old belts have been stretched to the max. Tighten to the correct tension, too much just damages the belts and the bearings in the alternator,a/c, or powersteering; too little allows them to slip and damages belts through overheating.

This is also a good time to check that the auto trans hoses leading to the cooler in the bottom of the radiator are in good condition and the clamps are tight.
Why not replace these hoses, and while you are there, the top and bottom radiator hoses as well?
Then you'll know that it has been done.

Posted on Jan 15, 2009

  • 10 Answers

SOURCE: Removal of air bag

You should disconnect the batter and wait for 15 to 20 min before remove the bag because you want air bags to de energize

Posted on Apr 13, 2009

  • 1 Answer

SOURCE: heater plugs for nissan terrano 2

i have a nissan terrano 2.7 dti heater light not coming on some times dose and some times does'nt and it wont start

Posted on Mar 20, 2010

  • 11800 Answers

SOURCE: Front wheels not moving in

The grease seeps out when the seal is worn out or defective. In your case it appears it's defective: a bearing in the front differential broke, it locked the wheels and damaged the seal.
Repairing it will be a big job: you will have to completely dismantle the front differential. In the mean time disconnect all the shafts to it and use the truck strictly as an 2WD.

Posted on Mar 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Something is loose in the steering wheel. How do I remove the cover? Nissan Terrano 11


If you have an SRS bag in the wheel, do not try this at home. Check the web to see what happens if you stuff up. You are dealing with an explosive and it's activating mechanism. Go to an expert.
non SRS wheels, start at the back and undo the two recessed screws holding the cover to the wheel. Follow your nose from there.

Jun 24, 2014 | Nissan Terrano Cars & Trucks

2 Answers

Air bag clock spring replacement


You will have to remove your steering wheel to replace this. First disconnect your ground on your battery. Let the car sit for a couple minutes to make sure all charge is out of the wires. On both sides of the steering wheel, there will be to little square covers. Take those off. there will be a torque bolt behind these covers. Remove those. After doing this, your air bag on the steering wheel will be able to be removed. then your ill see a nut in the middle of the steering wheel. Remove this nut. The next step can be done in two ways. one you can get a steering wheel puller to remove the steering wheel, or you can grab a hold of the steering wheel on both sides and shake the steering wheel loose. This will work most of the time but may not. After removing the steering wheel your clock spring will be underneath it. There is either two or four screws holding this on. install in reverse order. When you put your steering wheel back on, there are marks on the rod and the steering wheel you will need to line up to make sure your steering wheel is straight. If you have any more questions, just ask me.

Jan 21, 2014 | 2005 Nissan Murano SL

1 Answer

I have a 1992 nissan terrano only my left rear wheel is getting power in 4WD


C clip that retains axel is broken or came off. Or the axel is bad.

Jan 12, 2014 | Nissan Cars & Trucks

1 Answer

How do you replace a blown bulb in the clocks of a nissan terrano 2


With difficulty, as you have to remove the dashboard to do so. Some say fitting LED lights means you will never have to do this job again.........

Aug 04, 2013 | 2005 Nissan Terrano 2.7

2 Answers

Hi my nissan terranos steering shakes at 60 mph at 70 mph it doesnt at 50 mph it doesnt shake,


Get the front wheels re-balanced, a balance weight may have fallen off or been knocked off, or perhaps just due to tyre wear.
Due to harmonic frequencies, it is possible to get the vibration only at certain speeds.

May 22, 2011 | 2002 Nissan Xterra

2 Answers

How to adjust the handbrake on a terrano ll


On the inboard side of the rear wheel hubs, you will find an oval rubber plug, pry this plug out, to gain access to the brake adjuster.
Pull the handbrake up two clicks.
Jack and support. Remove the rear wheel, and adjust the brake using a screw driver levered through the slot to turn the notched wheel of the adjuster, until the hub starts to drag when rotated by hand. Repeat for the other side. Note the ratchet mechanism on the adjuster will only let it turn one way.

May 03, 2010 | 1994 Nissan Pickup

2 Answers

My speed alarm is set at 105 how do i adjust this function?


have to add a comp chip to comp to over ride the gov.

May 25, 2009 | 1991 Nissan Pathfinder

3 Answers

Seized thermostat


Not always. If you have a KA24E (2.4L 4 cyl) engine, the thermostat is located where the lower hose connects to the engine. I have had to change mine. It's easiest to get to if you remove the power steering pump and set it to the side. The thermostat housing is directly below where the PS pump mounts.

Dec 04, 2008 | 1995 Nissan Pathfinder

2 Answers

Nissan terrano headlight


check out
http://www.sferamydlo.com.pl/Zbyszek/Nissan/R20/el.pdf


Bulb Replacement
The headlamp is a semi-sealed beam type which uses a replacable
halogen bulb. The bulb can be replaced from the engine compartment
side without removing the headlamp body.
I Grasp only the plastic base when handling the bulb. Never
touch the glass envelope.
1. Disconnect the battery cable.
2. Disconnect the harness connector from the back side of the
bulb.
3. Pull off the rubber cap.
4. Press end of the retaining pin together to release bulb.
5. Remove the headlamp bulb. Do not shake or rotate the bulb
when removing it.
6. Install the new bulb in reverse order of removal.

Nov 11, 2008 | 2005 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

300 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...