Question about 1999 Chevrolet Venture

1 Answer

Cylinder head bolts pattern for a 99 venture 3.4

I need to know the tightning sequence for the front and rear cl\ylinder head bolts. Had them marked, but something happened.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 74 Answers

Out ward spiral pattern starting from the middle

Posted on Oct 26, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1201 Answers

SOURCE: Am I having one problem or several with my Chevy Venture?

sounds like there is a short in the turn signal switch. have to pull steering wheel to fix or replace.

Posted on Jan 28, 2009

joecoolvette
  • 5660 Answers

SOURCE: cly head torque settings

There are four bolts on top, and four bolts on bottom.
At the Top, starting from the Left side, the bolts are numbered ->
6, 2, 3, and 7.
At the Bottom, starting from the Left side, the bolts are numbered ->
5, 1, 4, and 8.

Sequence for tightening, of course, is to go from 1 through 8.
The best way to torque engine head bolts, is to tighten in a three stage tightening sequence. The bolts are finally tightened to 33 Foot Pounds,
and an additional turn of 90 degrees. Not trying to insult your
intelligence in any way, but I would like the additional 90 degree turn,
to be clear.
There are 360 degrees in a circle. If you go halfway, you have gone 180
degrees. If you go one-fourth the way, you have gone 90 degrees.
When you are getting ready to torque this final 90 degree turn, look to
make sure the end of your torque wrench has a clear path, so that you
will not be stopped somewhere along the way.

I advise torquing the head bolts to 15 lbs first. Then 25, then 33. Then go back one more time, for the additional 90 degree turn. Seems like a lot of hassle, but it's easy to warp this head. Remember, if you are not using some type of permatorque head gasket that has teflon, Like a Felpro Blue for example), after the engine has reached operating temperature Once, you have to go back, and retorque the head.

Posted on May 17, 2009

  • 335 Answers

SOURCE: cylinder head bolt torque chevrolet 3.4

here is the troque spec for the cylinder heads.

Cylinder Head Bolt

  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees
Cylinder Head Bolt
  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees


Cylinder Head Bolt
  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees
first pass 44 ftlbs
second pass 95 degrees

Posted on Jun 19, 2010

  • 3640 Answers

SOURCE: i need the engine torque specs for 99 chevy malibu

99 chevy malibu v6 3.1 engine, head bolt torque is-- 98 through 2001 is step1- 37 foot lbs, step 2- rotate an additional 90 degrees (1/4 turn). the rocker arm bolts are 168-in. lbs.

Posted on Sep 07, 2010

  • 95 Answers

SOURCE: 1997 cavalier head gasket replacement with a 2.2.

Go onto Autozone.com and sign up for their online repair. It is free to use but you have to register.

Posted on Dec 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs and sequence for the intake and head gasket on a 1999 Chevy Silverado 6.0l V8 K2500


Cylinder Head Bolts (First Pass all M11 Bolts in Sequence)
30 N?·m
22 lb ft
Cylinder Head Bolts (Second Pass all M11 Bolts in Sequence)
90 degrees
Cylinder Head Bolts (Final Pass all M11 Bolts in Sequence-Excluding the Medium Length Bolts at the Front and Rear of Each Cylinder Head)
90 degrees
Cylinder Head Bolts (Final Pass M11 Medium Length Bolts at the Front and Rear of Each Cylinder Head in Sequence)
50 degrees
Cylinder Head Bolts (M8 Inner Bolts in Sequence)
30 N?·m
22 lb ft
Intake Manifold Bolts (First Pass in Sequence)
5 N?·m
44 lb in
Intake Manifold Bolts (Final Pass in Sequence)
10 N?·m
89 lb in
Intake Manifold Wiring Harness Stud
10 N?·m
89 lb in

Oct 27, 2015 | Cars & Trucks

2 Answers

I need the torque spec for the valve cover on a 06mercury malin


There is a torque spec for the cylinder head; I don't know of one for the cover.

Jul 14, 2015 | Cars & Trucks

1 Answer

I need head bolt torque specs for a 2000 cadillac deville dts..


DeVille, Eldorado, Seville 1999-2005

Cylinder Head

Print


Removal & Installation

Left Side

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Alternator Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Power steering return hose retaining bolt from the cylinder head 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket.
  5. Clean the head mating surfaces.

To install:

0996b43f80231662.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Left cylinder head bolt torque sequence-4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees
    2. Step 2: Turn an additional 60 degrees
    3. Step 3: Turn an additional 60 degrees (total 190 degrees)

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm)
  4. Install or connect the following:

    Power steering return hose retaining bolt to the cylinder head and tighten to 37 ft. lbs. (50 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Right Side
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Electrical connector from the Engine Coolant Temperature (ECT) sensor Nut attaching the coil cassette ground wire to the cylinder head Bolt attaching the exhaust crossover pipe to the cylinder head Bolt attaching the right transaxle mount bracket to the cylinder head Bolt attaching the rear transaxle brace to the transaxle Nuts attaching the rear transaxle brace to the cylinder head Rear transaxle brace 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket
  5. Clean the head mating surfaces.

To install:

0996b43f80231663.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Right cylinder head bolt torque sequence- 4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees.
    2. Step 2: Turn an additional 60 degrees.
    3. Step 3: Turn an additional 60 degrees (total 190 degrees).

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm).
  4. Install or connect the following:

    Rear transaxle brace over the studs located at the rear of the right cylinder head Nuts attaching the rear transaxle brace to the cylinder head, loosely Bolts attaching the rear transaxle braces to the transaxle and tighten to 37 ft. lbs. (50 Nm) Nuts attaching the rear transaxle brace to the cylinder head and tighten 37 ft. lbs. (50 Nm) Electrical connector to the ECT sensor Bolt attaching the exhaust crossover pipe to the cylinder head and tighten to 18 ft. lbs. (25 Nm) Nut attaching the coil cassette ground wire to the cylinder head and tighten to 13 ft. lbs. (17 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Apr 16, 2013 | 2000 Cadillac DeVille DTS

1 Answer

Whats the bolt pattern for my 1995 ford escort head?


1.8 liter..NOTE: Lubricate the cylinder head bolts using the specified engine oil.

Install the cylinder head bolts. Tighten the cylinder head bolts in 2 or 3 steps in the sequence shown to 76-81 Nm (56-60 lb-ft).

b064be7.gif
1.9 liter
Apply a light coating of engine oil to the threads of the new cylinder head bolts. Install the new cylinder head bolts to the cylinder head. Following the sequence shown below, tighten the cylinder head bolts to 40-60 Nm (30-44 lb-ft). Loosen all cylinder head bolts approximately two turns, then retighten the cylinder head bolts to 60 Nm (44 lb-ft) following the sequence shown. After tightening, turn all bolts 90 degrees, in the same sequence. Complete bolt tightening by turning them an additional 90 degrees, in the same sequence. 398246b.gif

Aug 21, 2010 | 1995 Ford Escort

1 Answer

What is the right Torque Specification of the cylinder head bolt,main bearing and connecting rod bearing for a 1997 Ford F 150 4.2 liter? Thank you...


Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

May 17, 2010 | 1997 Ford F150 Regular Cab

2 Answers

Head gasket torque specifications and sequense


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence—3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence—3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Mar 06, 2010 | 2001 Chevrolet Venture

    1 Answer

    What is the bolt torque settings for an intake manifold on a 1973 Ford Mustang Mach 1 with a 351C and 2-barrel heads? Also, Where can I find a diagram showing the sequence or pattern for placing the intake...


    Intake Manifold 5/16 Bolts Non-Hardening sealers 25 ft-lbs
    Cast Iron Heads 3/8 Bolts 30 ft-lbs

    The torque sequence is snug all down then just star left rear then right front then right rear then left front and so on

    Nov 27, 2009 | Ford Mustang Cars & Trucks

    2 Answers

    What is the tension on cylinder head bolts for a jeep grand cherokee 307935 4 litre, 6 cylinder, 1999, petrol motor.


    Coat threads of left hand front bolt with sealant: 1st - step; - 22 ft./lbs. 2nd - step; - 45 ft./lbs. 3rd - step, all bolts except L.H. front bolt; - 110 ft./lbs. 4th - step, L.H. front bolt; - 100 ft./lbs. fig100.png

    Sep 05, 2009 | 1999 Jeep Grand Cherokee

    1 Answer

    Need to know cylinder head bolt torque specs


    Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

    Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

    1 Answer

    1994 cavelier


    Which of the two engines?
    2.2L - cylinder head bolts: long (back) bolts 46 ftlbs; short (front) bolts 43 ftlbs starting from center back in spiral pattern; then tighten bolts an additional 90 degrees in same sequence.
    3.1L - cylinder head bolts: coat threads with sealer tighten to 33 ftlbs starting from center front in spiral pattern; then tighen bolts an additional 90 degrees.

    Aug 02, 2008 | 1994 Chevrolet Cavalier

    Not finding what you are looking for?
    1999 Chevrolet Venture Logo

    114 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8152 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...