Question about 1997 Mercury Villager

1 Answer

Acceleration not showing a diagnostic code but wont accelerate over 10 mph

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 74 Answers

Those vans are really bad for input and output shaft sensors on the transmission

Posted on Oct 26, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Throttle position sensor


Check the fuel pressure under load and also have the exhaust system checked for excessive back pressure.

Mar 16, 2017 | 2006 Toyota RAV4

1 Answer

Blazer will not accelerate over 3000 RPM will drive 15 MPH but no more


run fault codes to determine why the CPU placed the engine in limp mode. Check oil and coolant levels.

Jan 01, 2014 | 1991 Chevrolet S-10 Blazer

1 Answer

I have a 2004 Saturn Ion. The car will not accelerate beyond 35 mph with the gas pedal totally to the floor. The car is making a wheezing like sound as she goes. The check engine light came on and the...


Have the cat converter check for failure and blocking the exhaust pipe. No codes will show . Test by hitting the cat converter with the heel of your hand and if it rattles get a new one.

Aug 21, 2013 | 2004 Saturn ION

1 Answer

04 saturn L300


Next time the engine light comes on, get the codes pulled and get back to me

Apr 15, 2013 | Cars & Trucks

1 Answer

Accelerator wont accelerate


Hello
The engine and automatic transmission in this vehicles drive train are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPENDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM

Aug 07, 2012 | 2006 Toyota Avalon XLS

1 Answer

Looking for adaptor to scan trouble codes 1990 maxima v6


How to read the engine codes without a Nissan CONSULT or scan tool. (Set ECM in Diagnostic Test Mode II)
  1. Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.
  2. Repeat the following procedure quickly five times within 5 seconds.
    1. Fully depress the accelerator pedal.
    2. Fully release the accelerator pedal.
  3. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the MIL starts blinking.
  4. Fully release the accelerator pedal.
  5. ECM has entered to Diagnostic Test Mode II (Self-diagnostic results).

Aug 10, 2010 | 1990 Nissan Maxima

2 Answers

Not Ready for Smog test


it is not how many miles but the type of driving.

here is a OBD2 drive cycle test.

Generic OBD II "Drive Cycle" Most OBD II ("On-Board Diagnostics II") diagnostic monitors will run at some time during normal operation of the vehicle.
However, to satisy all of the different Trip enable criteria and run all of the OBD II diagnostic monitors, the vehicle must be driven under a variety of conditions. The following drive cycle will (theoretically) allow all monitors to run on (??) vehicle. (Note: Drive cycle specifics vary by vehicle!)
  1. Ensure that the fuel tank is between 1/4 and 3/4 full.
  2. Start cold (below 86°F /30°C) and warm up until engine coolant temperature is at least 160° F (typically requires at least one minute; up to 3 minutes).
  3. Accelerate to 40-55 MPH at 25% throttle and maintain speed for five minutes.
  4. Decelerate without using the brake (coast down) to 20 MPH or less, then stop the vehicle. Allow the engine to idle for 10 seconds, turn the key off, and wait one minute.
  5. Restart and accelerate to 40-55 MPH at 25% throttle and maintain speed for two minutes.
  6. Decelerate with using the brake [or the clutch!] by coasting down to 20 MPH or less, then stop the vehicle. Allow the engine to idle for 10 seconds, turn the key off, and wait one minute.

Jun 04, 2010 | 2001 Kia Sephia

1 Answer

1992 ford tempo 2.3L diagnostic code 10, what does it mean


10 means you do not have a code problem. Could have a computer problem.

Jun 28, 2008 | 1992 Ford Tempo

Not finding what you are looking for?
1997 Mercury Villager Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

fordexpert

Level 3 Expert

5467 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...