Question about 2007 Opel Corsa 1.0

Open Question

Opel corsa 1.4 lite setting cam belt timing

Timing marks on cam and crank

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 17115 Answers

SOURCE: timing marks on engine

Use the timing marks on the damper for the crank and bring it to 0 on the cam there are marks that correspond with a mark on the head. Look on autozone dot com and put in the year make and model then look at the free repair guides.

Posted on Oct 10, 2012

Ad
alicantecoli
  • 22326 Answers

SOURCE: How to set pump, crank and cam timing on opel corsa 1.7d utility, model 2003

Not sure here as to the type as some have a bolt in the block in line with the crank and special tool is used to locate TDC ,If the timing belt broke then you have bent valves anyway so the head will have to come off .If you reply with more details then i will advise how to do it with no timing marks also is this a common rail with just a high pressure pump or is it a intermediate with injector pump but the injectors having electronic sensor on one of the injectors if that makes sense to you

Posted on Oct 19, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instruction changing timing belt 1979 Alfa Romeo Spider Veloz?


With Cam Caps loosened, FIRST loosen timing chain tensioner, press it in to loosen tension, Crank using ratchet to TDC (Top Dead Center on crank pully, (to keep from damage to pistons), align Exhaust Cam Timing Mark to mark on #1 Exhaust cam cover, then take up slack between Exhaust & Intake Cams (on top between the cams), Then align the Intake Cam to mark on #1 Cam Cap, "Now" loosen the 17mm bolt to tighten timing chain, rotate engine using rachet two times, reset TDC at the crank, and look at "Cam Timing Marks on both the Exhaust, and Intake Cams. If you did all this correctly the "Timing Marks" should be lined up so TDC,Exhaust, and Intake marks are all the same.

Oct 10, 2014 | 1979 Alfa Romeo

2 Answers

Timing belt setting


line up the marks on crank shaft gear arrow to arrow, the front cam gear the mark goes to the middle on the rear cam gear the mark goes one notch below front gear mark they line up when the tension is put on belt.

Aug 17, 2014 | 2005 Chrysler PT Cruiser

2 Answers

Problems of gm


You can rotate the cam/crank into a positon that will not move as you remove the old belt, as long as the new belt places the cam/crank in same position as the old belt had them, it don't matter where the timing marks are. Leave your old belt on, rotate to a position that will not move or have tension on belt, (no matter the marks) and replace the belt. Make sure to recheck timing marks after new belt is installed by rotating the crank/cam back to timing marks, or just trust that the belt was replaced without the cam or crank rotated. Easy off, easy on, just make sure the cam/crank are still in time as the old belt had them located. NOTE: timing marks are there in case of a broke belt, or for a car that has jumped time. As long as cam and crank are held in same positon, and car was in time before the procedure, it don't matter where the timing marks are at during belt replacement.

Dec 15, 2013 | Cars & Trucks

2 Answers

Cam Crankshaft timing


8 degrees before tdc

Mar 10, 2010 | 1983 Chevrolet Chevy

1 Answer

Changed timing chain and need to align to cam with the crang


Align the chain with the colored links on the chain over the marks on the cams.Twin cams Have a small hole on the cam gears that will align with a hole in the front of head.Crank Gear has a pip mark that goes straight up.colored links on crank go to the 5 & 7 Oclock position on the lower crank gear with pip mark on crank gear at 12:00.Hope this helps

May 22, 2009 | 1995 Saturn Sl

1 Answer

91 chevy G20


well not sure exactly why it wont line up use something to turn the crank and cam to appropiate position start sliding crank gear until cam gear is touching then start to push both at same time make sure your crank key and cam pin are bothin place On many OHV pushrod engines, the crankshaft sprocket is installed on the crankshaft nose and the crankshaft is rotated to position piston #1 at TDC. At this point, a mark stamped onto the crankshaft sprocket is pointing directly upward (toward the camshaft).
The camshaft sprocket is then temporarily bolted to the cam and used to rotate the cam until a mark stamped on the cam sprocket is pointing directly downward (toward the crankshaft). The sprocket is then removed from the cam (without allowing the cam to rotate).
The timing chain is looped over the cam gear, the mark on the cam gear is positioned directly downward, and the chain is looped around the crankshaft sprocket. When the cam sprocket is attached to the cam, the timing marks on the crank and cam sprockets should be pointing toward one another.

Feb 10, 2009 | 1992 Chevrolet G20

1 Answer

NEED TIMING MARKS 2.0L DUAL CAM FORD CONTOUR


the cam marks are on the cams under the valvecover the crank has a mark o nthe timing cover that you need to line it up to

Jan 02, 2009 | 1996 Ford Contour

1 Answer

Timing Belt Markings


Mark are on the crank and cam timing gears. Cam gear mark at 12 o"clock crank gear mark lined up with TGC mark on block when installing timing belt.

Dec 16, 2008 | Hyundai Motor 2002 Elantra

1 Answer

TIMING MARKS??


normally on most cars there is a mark indented in the cam\cams and a matching mark on the block usally a small dot. and the same on the crank on some cranks it also has a degree mark for setting the advance timing at the crank...not always though

Jul 14, 2008 | 1998 Plymouth Breeze

4 Answers

Timing marks on volvo s40


the crank has the only mark you have a procedure for the cam gear you should see if the local dealer will print this out for you

Jul 01, 2008 | 2004 Volvo S40

Not finding what you are looking for?
2007 Opel Corsa 1.0 Logo

Related Topics:

1,304 people viewed this question

Ask a Question

Usually answered in minutes!

Top Opel Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Brad Brown

Level 3 Expert

17115 Answers

The Scrivener

Level 2 Expert

154 Answers

Are you an Opel Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...