Question about 2001 Chevrolet Blazer

1 Answer

MY 01 4WD Blazer power side mirrors will not move / not working

The controls on the doors are not resetting the sid view mirrows

Posted by on

  • Gary Jacobson
    Gary Jacobson Mar 11, 2009

    I have the same problem with my 2002 mercury grand marquis. POWER SIDE VIEW MIRRORS QUIT WORKING.

  • Anonymous Mar 18, 2009

    My side mirrors are not working with the control buttons.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 188 Answers

You might have a bad switch or a broken cable to the mirrow???? I would lean more toward the bad switch. try cleaning it with contact cleaner or spray it with WD-40.

Posted on Feb 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Knocked rear view mirrow off


if you are talking the rear view mirror on the windscreen then use Loctite 406 or 401 super glue to refit it. care with the glue as it will stick skin together real quick. have a bottle of nail polish remover or acetone on hand in case of accident.

Dec 19, 2013 | 2003 Kia Rio

1 Answer

Install side mirrow


To replace your side mirror, disconnect the battery's negative cable. Take off the interior door panel. Unplug the wiring harness if you have power-controlled mirrors. Take out the mirror bolts with either a socket wrench or a nut driver. Separate the actual mirror from the mirror assembly. Use a torx driver to extract the screws, and then pry the plastic tabs on the backing until the two pieces separate. Attach the new mirror to the assembly by snapping it onto the backing with the tabs.-----------------------------------------------------------------------------------------
Super VAG K+CAN V4.8

Apr 03, 2013 | 1998 Chevrolet Cavalier

1 Answer

Electrical problem with p/w p/l and mirrows 99 corvette


The most common issue is a broken wire or wires inside the plastic insulator of the wiring harness that runs through the rubber boot from the door to the body.

Feb 19, 2012 | Chevrolet Corvette Cars & Trucks

1 Answer

How to install side view mirrow


You can blame it on your significant other, blame it on the kids or blame it on someone hitting it in the crowded parking lot. Whatever the reason, the side view mirror on your car is broken, missing or hanging by a thread. It's not that hard to replace. With a few common household tools, you can replace it yourself in less than 30 minutes. Forget the body shop or service station; they're going to charge you more in labor than you paid for the part online.

How to Install Side View Mirrors
1.Open the door wide and roll the window all the way down so you don't damage it.
2.Locate the plastic molding on the opposite side of the rear view mirror at the very front corner of the door's window. It'll probably be black plastic triangular-shaped molding, but it may have the same hue as the interior of the vehicle.
3.Gently but firmly pry that triangular molding off with the screwdriver. It's only snapped into place and there's usually a small ridge or lip that seats down into the window cavity. This ridge/lip should be no more than a quarter of an inch into the cavity. Pry it from a couple of spots until it comes free.
4.Locate the wire harness and unplug the mirror if it is an electric-powered mirror.5.Locate the three nuts inside the cavity of the door. There may be some foam plugs or insulation you'll need to move out of the way, but you can replace them after you install the new mirror.
6.Remove the nuts with the ratchet, extension and appropriate-sized socket. Be careful not to drop them into the door cavity.
7.Remove the old mirror and install the new one.
8.Tighten all three nuts. Plug the mirror into the harness if it is a powered one and test it before you close everything upThank you for using FixYa hope this will help your problem and don't forgetto rate me.thanks,Josefina

Oct 19, 2011 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Need a diagram for installing a drivers side electric power mirror on a 1995 mercury villager van


here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal
  1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).




  1. Remove the wire clip.
  1. Disconnect the power outside rear view mirror electrical connector.




  1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.




Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal
  1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws.


    Remove the outside rear view mirror mounting hole cover.
Installation
To install, reverse the removal procedure. Mirror Control
Removal
  1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).


May 13, 2010 | 1995 Mercury Villager

1 Answer

Replace drivers side mirror on 94 s-10


Take off door panel..it has plastic retainers so give it a good yank. May have to take screws out of arm rest and be easy with the door handle not to force it and break. The mirrow will be held on with a couple bolts/perty easy once you get the cover off..

Dec 17, 2009 | 1994 Chevrolet S-10 Blazer

2 Answers

How to remove/replace driver's side mirror on 96 blazer


remove door panel.. there should be access hole to get to the bolts.

Jul 31, 2009 | 1996 Chevrolet Blazer

1 Answer

Need instructions to install replacement side view mirrors for 95 chevy blazer


You will have to remove the door panel, behind the triangle piece on the top right of the drivers side door panel you will see 3 nuts which hold the mirror in place. Remove the nuts and the mirror should come right off the door. Same on the passenger side.

Jun 03, 2009 | 1995 Chevrolet Blazer

1 Answer

How to ajust wing mirrows on audi tt


If your tt is equipped w/ power mirrors the switch is on the driver door panel behind the master window switch.  Just twist knob either left or right.  then move knob up or down, or side to side.  Do this with the vehicle on or running.  If switch is in middle it will not do anything.

Mar 22, 2009 | 2000 Audi TT

Not finding what you are looking for?
2001 Chevrolet Blazer Logo

Related Topics:

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...