Question about 2005 Chrysler PT Cruiser

Open Question

Pt cruiser fl0007 ee18 bl01

Trouble codes ,engine revs to 3000rpm and shifts slowly won't pull hills

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
StormStrikes
  • 104 Answers

SOURCE: have a 03 pt cruiser

The P0302 Code points to a misfire detected on the # 2 cylinder. If its stumbling, I would first suspect the plug or wire is bad. I believe the ignition coil on that vehicle is a single coil pack with four terminals, so if only the P0302 code is coming up I would start with the plug and wire. May be time to do a tune up and just replace all the splugs and spark plug wires.

Posted on Dec 30, 2008

Ad
  • 38 Answers

SOURCE: check engine light on and code po108

PO108 (map circuit high input) MAP is manifold absolute pressure... a sensor normally mounted on the intake. your code is suggesting a problem with this sensor, or its circuitry.

Posted on May 11, 2009

  • 14036 Answers

SOURCE: Engine light codes P0551 and P1684

CODE PO551 -POWER STEERING PRESSURE SWITCH CIRCUIT FAILURE. CODE P1684 - BATTERY HAS BEEN DISCONNECTED.

Posted on Aug 23, 2009

  • 1 Answer

SOURCE: Check engine light comes on, car sputters, loses power

you need to change you crank shaft positioning censor

Posted on Sep 06, 2009

  • 10 Answers

SOURCE: DIAGNOSTIC code P01A4 for pt cruiser

my old amns cruiser has the same problem i'm putting it down to loss of turbo pressure as the inlet manifold is leaking when reved
i'll let you know when manifold is replaced if it cures it

Posted on Sep 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont rev above above 3000rpm


Hi Anonymous, I want to help you with your question, but I need more information from you. Can you please add details in the comment box? Such as what kind of vehicle

Sep 01, 2014 | Cars & Trucks

1 Answer

VW 2013 Golf Automatic stays in 1st gear when driving uphill. Have to pull over after hill, stop, park and then go for engine to autocorrect. VW service center mechanic says this is how it's supposed to be...


There is no problem with the revs going to 3 or 6. The revs need to climb so you have enough power to climb the hill (if the car upshifts under heavy load it may stall). But are you saying that the only way you can get it to shift out of first is to turn off the car? if so, then that is obviously not supposed to happen. It should shift shortly after you start driving down hill.

Aug 20, 2013 | Volkswagen Cars & Trucks

1 Answer

Not shifting


Any transmission trouble code will put the trans in second gear
and it won\'t shift.
Key on-off-on-off-on without starting the engine will illuminate
the check engine light .It will flash out the codes.Should see a 55
code ,5 flashes,a pause then 5 more. Any codes other than 12 and
55 need recorded for further diagnnosis.
I was thinking that turning the key on and opening the throttle wide
open 4 times within 5 seconds (engine off)clears tranny codes,not sure about that tho. You might try it then drive it and see if it shifts,although
as soon as the malfunction happens again it will go back into limp mode.
Tranny slipping or a slow shift or converter lock up malfunction along
with many other things will trigger this.

Mar 16, 2013 | 1999 Plymouth Grand Voyager

1 Answer

Won't shift properly


Your probably pulling OBD Code P0758, just like mine is. Ive changed the trans in a customers car now 3 times with the same result. Hard shift into rev and 2 but no third gear. I believe its the TCM or wiring harness. Check to have the TCM Completely flashed and re-written by the dealer, this may help, if Not replace the TCM is my only other options, because I do not believe that 3 transmissions have been bad.

Jul 15, 2012 | 2008 Ford Fusion

1 Answer

1994 gmc sierra pickup 4.3L V6 automatic transmission experiencing difficulties with ODrive = 4th gear, and Drive = 3rd gear, engine revs up to the max properties with little to no forward motion. Rev


You have internal transmission damage I expect the clutches on third and fourth gear are wiped out. Its either that or a solenoid gone bad that holds those clutches pressure get it in a transmission shop soon to avoid whole transmission replacement costs.

Mar 19, 2012 | Cars & Trucks

1 Answer

Why can't I pull trouble codes for my 1994 Buick


You need a specific adapter to scan your trouble codes. Vehicles prior to 1996 use OBD1 scanners, which are very expensive. Your best bet is to call around a few shops in your area and ask what they would charge to diagnose the code. It sounds like you may have more than 1 problem. The emissions could be due to a bad oxygen sensor and acceleration problem may be due to bad plugs, plug wires, clogged fuel filter, rotor and distributor cap, etc. Do a tune up on it, then see where you stand. At least you won't have to pay a shop to do it if that fixes your acceleration problem.

Sep 03, 2011 | 1994 Buick Regal Gran Sport

1 Answer

Mazda Sentia 929 auto failure


Rebuilt gearbox probably... unfortunately!
If the HOLD light in the in strument cluster is flashing at you, it is giving you a transmission diagnostic code (like a kind of Morse Code). A transmission specialist or a Mazda Dealer will be able to read this code and plug their computer into the cars computer, and tell you what is wrong.

Feb 28, 2009 | 1993 Mazda 929

Not finding what you are looking for?
2005 Chrysler PT Cruiser Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...