Question about Cars & Trucks

Open Question

Locaon of the crankshaft position sensor on a 2007 saturn vue with a 2.2 engine

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

FixurNissan
  • 61 Answers

SOURCE: check engine light on . engine speed sensor

The engine speed signal code is generated from the crank sensor. The crank sensor is located on the back side of the engine block. See image.

Thanks Jay!dd6b033.jpg

Posted on Jul 21, 2009

rteemon
  • 578 Answers

SOURCE: Service Engine light on Green line 2007 Saturn Vue

take the ground line of the battery and press the brake for a few minutes and if the life is still on have the vehicle scann and clear code and have the emission components for the vehicle check

Posted on Sep 12, 2009

emissionwiz
  • 75822 Answers

SOURCE: service engine soon light on 2003 Saturn Vue

Here is the definition of the code in GM manual:
P0128 - Coolant Thermostat Below Thermostat Regulating Temperature, this indicates the engine is running cold, u need a thermostat

Posted on Feb 12, 2009

csmock132
  • 4669 Answers

SOURCE: Where is the crankshaft position

It is stuck in bellhousing of the transmission near the rear head. The new crank sensor will come with a piece of gasket paper on the end of the sensor. Install the sensor all the way in against the pick-up wheel. When you crank the engine the wheel will rip off the paper and the adjustment will be correct.

Posted on Mar 10, 2009

DSMprostyle
  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It won't start. No current from crank sensor to ECM. Wiring diagram checks out.


Hey Bob how's it going ? What engine does it have 2.2 3.5 L ? An how did you test for current ? This is a AC voltage .
The crankshaft position (CKP) sensor is a permanent magnet generator, known as a variable reluctance sensor. The CKP sensor produces an AC voltage of different amplitude and frequency. The frequency depends on the velocity of the crankshaft. The AC voltage output depends on the crankshaft position and the battery voltage. The CKP sensor works in conjunction with a 7X reluctor wheel attached to the crankshaft. The CKP sensor produces seven pulses for each revolution of the crankshaft. The pulse from the 10-degree notch is known as the sync pulse. The sync pulse is used to synchronize the coil firing sequence with the crankshaft position. The CKP sensor is used for ignition timing, the fuel injector timing, misfire diagnostics and tachometer display. The CKP sensor is connected to the ECM by a signal circuit and a low reference circuit.
The best way to test is with a lab scope !
Crankshaft position sensor

Apr 30, 2015 | 2004 Saturn VUE

1 Answer

What does the crankshaft position sensor do in my 2003 saturn vue


It lets the computer know the position of the crankshaft and piston so that it can inject fuel at the proper time.

May 24, 2014 | 2006 Saturn Vue

1 Answer

What are these codes p1779, 11780,po440,po341, replaced cam position censor


Try replacing the crankshaft position sensor. I had a 1998 dodge ram that had that same issue. Thats what it was.
Its by the flywheel under the vehicle. probably on the passenger side.

Apr 05, 2014 | 2002 Saturn VUE

1 Answer

No crank signal


Change the ECM too if they can exchange. Your car controlled by ECM so see this work.

Dec 19, 2013 | 2006 Saturn Vue

1 Answer

What causes the o2 sensor to malfunction ?


Could quite possibly due to a damaged or otherwise worn out catalytic converter.

Sep 18, 2012 | 2007 Saturn VUE FWD 4

1 Answer

Good Day! i have a 2005 Saturne vue and im running in to this problem..i'll be driving down the road for a while and after and 30 min or so the engine will loose all power and die after 30sec or so when i...


Check the crankshaft position sensor. Old oil (infrequently changed) can foul them up. The sensor has to "see" certain points on the crankshaft. Dirty or bad oil can prevent the "seeing" from occuring. You can turn the key all you want, it will crank but never start. Sometimes, when the sludge settles, it will run again. If this solves your problem, you seriously need an engine flush and then frequently change your oil. Clean oil is more importaint than most people realize. hope this helps.

Sep 01, 2010 | 2005 Saturn VUE

1 Answer

2005 SATURN VUE stalling at 60mph?


Iit seems that the computer got "confused". A way is to remove the negative battery cable for about a minute then reconnect. This will try to reprogram the computer. If it is still not good, try checking the CPS crankshaft position sensor and the IPS idle position sensor.

Dec 15, 2008 | 2002 Saturn VUE

1 Answer

Crankshaft position sensor


Usually, the crank sensor sits on the bottom of the engine and usually on the drivers side. Some other places it might be is on the passeger side at the bottom and also on the transmission bellhousing near the bottom on either side. Hope this gives you some direction. Thanks for Using FixYa!

Sincerely,

JC

Nov 28, 2008 | 2003 Saturn VUE

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...